Résumé du contenu de la page N° 1
P Please read this manual and save it Please read this manual and save it lease read this manual and save it
with your original sales receipt. w with your original sales receipt. ith your original sales receipt.
T T To ools needed for assembly: Phillips acrewdriver ools needed for assembly: Phillips screwdriver ols needed for assembly: Phillips acrewdriver
( (not included); Assembly Wrenches (included). (not included); Assembly Wrenches (included). not included); Assembly Wrenches (included)
Résumé du contenu de la page N° 2
TABLE OF CONTENTS TABLE OF CONTENTS Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Parts Picture . . . . . . . . . . . . . . . . . . . . . .
Résumé du contenu de la page N° 3
IMPORTANT INFORMATION ELECTRICAL HAZARD DANGER To prevent electric shock, do not immerse in water; wipe clean with a damp cloth. WARNING • Battery can fall out and injure a child if vehicle tips over. Always use the battery retainer. • PREVENT FIRE - Ne ver modify the electrical system. Alterations could cause a fi re resulting in serious injury and could also ruin the electrical system. - Use of the wr ong type battery or charger could cause a fi re or explosion resulting in serious injury.
Résumé du contenu de la page N° 4
PARTS • If you experience a problem with this product, or are missing a part, please call us at 1-800-348-0751, rather than return this product to the store. • Please identify all parts before assembly and save all packaging material until assembly is complete to ensure that no parts are discarded. • Metal parts have been coated with a lubricant to protect them during shipment. Wipe all metal parts with a paper towel to remove any excess lubricant. Seat Vehicle Hood Pretend Motor Windshield St
Résumé du contenu de la page N° 5
PARTS Steering Column Steering Wheel Cover 2 Side Mirrors 4 Wheels 4 Hubcaps Steering Wheel 4 Hubcap Covers Rear Axle 2 Rear Wheel Drivers 2 Side Windows R1500pr-0920 5
Résumé du contenu de la page N° 6
PARTS 2 Bushings 3 /8" -16 Hex Nut - 5 Key 7 /16" Washer - 2 Wrench - 2 3 #8 x /4" Screw - 11 1" Bolt - 2 6 Volt Battery 1 #12-32 x 1 /4" Screw - 2 For your convenience, we included extra fasteners! Note: Tighten and loosen all screws with a Phillips screwdriver. Do not over-tighten the screws. Super 6 Volt Charger Part not shown: Label Sheet - 2 Fasteners Shown Actual Size R1500pr-0920 6
Résumé du contenu de la page N° 7
PARTS PICTURE Note: Some parts shown are assembled on both sides of the vehicle. 2 14 4 22 3 15 13 21 1 18 19 5 12 17 6 22 10 16 23 11 7 9 12 22 8 10 11 20 Parts Not Shown 1 Vehicle 9 Bushing - 2 17 Side Window - 2 2 Seat 10 Wheel - 4 18 Rear Axle 3 #8 x / " Screws - 11 Assembly Wrench 4 3 Hood 11 Hubcap - 4 19 Rear Wheel Driver - 2 1" Bolt - 2 Label Sheet - 2 4 Windshield 12 Hubcap Cover - 4 20 Super 6 Volt Charger 1 #12 x 1 / " Screws - 2 4 5 Pretend Motor 13 Steering Wheel 21 Motor (Ins
Résumé du contenu de la page N° 8
BATTERY CHARGING ELECTRICAL HAZARD CAUTION WARNING • Battery can fall out and injure a child if Use the charger in dry locations only. vehicle tips over. Always use the battery retainer. About Thermal Fuses • PREVENT FIRE ® Your Power Wheels 6 volt battery is equipped with a built-in - Never modify the electrical system. thermal fuse. The thermal fuse is a self-resetting safety device Alterations could cause a fi re resulting which automatically “trips” and shuts down operation of the i
Résumé du contenu de la page N° 9
BATTERY CHARGING ASSEMBLY WARNING Power Children can be harmed by small parts, Indicator sharp edges and sharp points in the vehicle's unassembled state, or by electrical items. Care should be taken in unpacking and assembly of the vehicle. Children should B not handle parts, including the battery, or help in assembly of the vehicle. CAUTION A In the unassembled state, this package contains Battery Charger small parts. Adult assembly is required. Connector Connector GAP NO GAP INCORRECT
Résumé du contenu de la page N° 10
ASSEMBLY Motors Seat Vehicle Hole in Motor Rear Axle Assembly 3 FRONT VIEW • Rotate the seat back and lift to remove from the vehicle. 5 • Slide the rear axle assembly through the hole in one motor, the Motors back end of the vehicle and then out through the other motor. Rear Wheel Driver (Ring Side Out) Rear Axle Wheel (Rib Side In) 4 TOP VIEW Motor Hubcap • Locate the motors inside the vehicle. (Peg Side In) • Make sure each motor is positioned in the rectangular recesses inside the vehicle
Résumé du contenu de la page N° 11
ASSEMBLY Steering Linkage Wrench Assembly 3 /8" -16 Hex Nut Rear Wheel Assembly 7 3 • Fit a /8" -16 hex nut onto the end of the rear wheel assembly. 9 • Tighten the hex nuts on both sides of the rear wheel assembly with the wrench. • Turn the vehicle so that the front end is toward you. Hint: An extra wrench has been provided to hold the hex nut • Fit the steering linkage assembly to the front end of the vehicle. on one side of the rear axle while tightening the hex nut on 1 • Insert two #12 x
Résumé du contenu de la page N° 12
ASSEMBLY Front Axle Hubcap (Peg Side In) Hubcap Wheel Cover 13 (Rib Side In) 11 • Fit and snap a hubcap cover to the hubcap. • Fit a wheel, rib side in, onto the front axle. • Repeat Assembly steps 10-13 to assemble a washer, bushing, • Slide a hubcap, peg side in, onto the front axle. wheel, hubcap, hex nut and hubcap cover to the other front axle. Front Axle Seat Tabs Wrench 3 /8" -16 Hex Nut 12 3 14 • Fit a /8" -16 hex nut onto each end of the front axle. Tighten both FRONT VIEW hex nuts wi
Résumé du contenu de la page N° 13
ASSEMBLY Label #8 Dashboard 17 DASH VIEW 15 • Lower the front end of the vehicle. 3 • Insert four #8 x /4" screws into the seat. • Apply label #8 to the dashboard, as shown. • Tighten the screws with a Phillips screwdriver. Straight End of Steering Column Steering Wheel Hole Steering Wheel Column Steering Steering Steering Cur C Cur urved ved ved Linkage L Linkage inkage E End End nd H Hole Hole ole 18 16 BOTTOM VIEW • Fit the steering wheel onto the end of the steering column and • Lift th
Résumé du contenu de la page N° 14
ASSEMBLY Key Wrench 3 /8" -16 Hex Nut Hole in Steering Column Dashboard 21 19 • Insert and “snap” the key into the hole in the dashboard. 3 • Fit a /8" -16 hex nut on the end of the steering column. • Tighten the hex nut with the wrench. Steering Wheel Cover Steering Wheel B A Side Window 22 FRONT VIEW 20 • First insert the tabs on the bottom edge of the side window into • At an angle, fit the tabs on one side of the steering wheel cover the slots on the side of the vehicle . A into the slot
Résumé du contenu de la page N° 15
ASSEMBLY Slots Windshield Side Mirror 23 25 FRONT VIEW • Fit a side mirror to the side of the vehicle. • Insert and “snap” the tabs at the top of the windshield into the slots in the top edge of the vehicle. 3 #8 x /4" Screws 24 RIGHT SIDE VIEW 3 • From the inside of the vehicle, insert two #8 x /4" screws 26 through the vehicle and into the side mirror. • Tighten the screws. 3 • Insert three #8 x /4" screws into the windshield. • Repeat Assembly steps 23 and 24 to assemble the other • Tighte
Résumé du contenu de la page N° 16
ASSEMBLY VEHICLE CARE • Check all screws, hex nuts and their protective coverings regularly and tighten as required. Check plastic parts on a regular basis for cracks or broken pieces. Pretend • During snowy or rainy weather, the vehicle should be stored Engine inside or under a protective cover. Remember to charge the battery at least once per month while your vehicle is not in regular use. • Avoid operating the vehicle in wet or snowy conditions, and do not spray the vehicle with a hose
Résumé du contenu de la page N° 17
DECORATION • Before applying the labels, wipe the surface of the vehicle with a clean, dry cloth to remove any dust or oils. • Place the labels exactly as shown in the illustrations. For best results, avoid repositioning a label once it has been applied to the vehicle. • After applying a label, rub the label firmly with a clean, dry cloth to make sure the label is adhered to your vehicle. Start at the center of a label, and smooth towards the outer edges to remove air bubbles. 1 16 15 17 14 20
Résumé du contenu de la page N° 18
DECORATION 5 6 22 3 31 27 27 32 32 34 33 34 33 RIGHT SIDE 7 35 2 4 31 27 27 32 32 34 33 34 33 LEFT SIDE R1500pr-0920 18
Résumé du contenu de la page N° 19
BATTERY INSTALLATION ® IMPORTANT! Use only a Power Wheels 6 volt lead-acid rechargeable battery. Use of any other battery will damage your vehicle. Make sure you charge the battery for at least ® 18 hours using the enclosed Power Wheels Super 6 volt charger before operating your vehicle for the first time. Charge the battery for at least 14 hours after each use of the vehicle. Never charge the battery longer than 30 hours. Failure to follow these instructions may damage your battery an
Résumé du contenu de la page N° 20
BATTERY CARE AND DISPOSAL Care Disposal ® If a battery leak develops, avoid contact with the leaking acid and • Your Power Wheels battery is a non-spillable, sealed lead-acid place the damaged battery in a plastic bag. See information below battery. It must be recycled or disposed of in an environmentally for proper disposal. sound manner. If acid comes in contact with skin or eyes, flush with cool water • Do not dispose of a lead-acid battery in a fire. The battery may for at least 15 min
