Résumé du contenu de la page N° 1
Thank You….
…for purchasing an Edelbrock Nitrous Oxide Injection System.
Nitrous Oxide injection is one of the most exciting performance enhancements, for the dollar invested, on the market today. With the use of nitrous
oxide come some important safety considerations. This manual has been written to help you during the installation and use of your Edelbrock
Nitrous System. Please read it completely before you install and use your system. Please pay close attention to the safety information at t
Résumé du contenu de la page N° 2
MERCURY MARAUDER PERFORMER EFI SERIES NITROUS SYSTEM Catalog #70406 Table of Contents Page # a. Before You Install Your Edelbrock Nitrous System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 b. What is Nitrous Oxide? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 c. Safety Tips for Working with Nitrous Oxide . . . . . . . . . .
Résumé du contenu de la page N° 3
Caution!! Before You Install Your Edelbrock Nitrous System… Please read this installation manual fully before installing this system. You will need to have available the following tools: Hand Tools ❑ Socket set including ratchets and extensions ❑ Screwdrivers ❑ Pliers ❑ Bench vise ❑ Wire crimping pliers, wire strippers ❑ Floor jack ❑ Vehicle jackstands ❑ Safety glasses Power Tools ❑ Power drill ❑ Drill bits (1/4”, 1/2” and 3/8”) You should understand the following skills: ❑ Power tool safety pro
Résumé du contenu de la page N° 4
WHAT IS NITROUS OXIDE? Nitrous Oxide is a cryogenic gas composed of nitrogen and oxygen molecules. It is stored as a “gas over a liquid” which means that both liquid and gaseous nitrous oxide is delivered into your engine. It is 36% oxygen by weight, which is what produces the added horsepower. By injecting more oxygen (and a corresponding fuel signal), we create the additional power much like a supercharger or a turbocharger does. Nitrous Oxide is considered an “oxidizer” and not a fuel. Nitrou
Résumé du contenu de la page N° 5
1.0 Introduction to your Edelbrock Mercury Marauder Performer EFI Nitrous System Within the pages of this manual is information, safety tips and operation instructions for your new Edelbrock Nitrous System. Watch for these symbols to know where to go for information. ….There is safety related information here. ….shows where technical information about your vehicle or specific skills that may help during installation. ….call Edelbrock Technical support hotline for more information. ℡ 1.1 Genera
Résumé du contenu de la page N° 6
1.2 Jet Map Information Edelbrock engineering has conducted dyno testing with the Edelbrock Mercury Marauder Performer EFI system to ensure the horsepower increase the nitrous system is as intended. On a typically stock 4.6L engine, you can expect the following approximate power gain: Nitrous / Jetting Approx. HP Gains 32/30 (Both Nitrous) 70 The dyno tests were conducted at Edelbrock using a stock 4.6L DOHC engine. These tests were conducted with 950 psi nitrous b
Résumé du contenu de la page N° 7
1.4 Mercury Marauder Performer EFI Series Bill of Materials QTY. DESCRIPTION QTY. DESCRIPTION Nozzle and Nozzle Hardware Fuel Pressure Safety Switch and Hardware 1 90º Nitrous fan spray nozzle 1 30 psi Fuel pressure safety switch 1 Straight Nitrous fan spray nozzle 1 Fuel Rail Hobbs adapter 2 Nitrous fan spray nozzle bulkhead body bolt 2 Nitrous fan spray nozzle bulkhead concave nut Bottle and Bottle Hardware 1 10-lb. Nitrous bottle Solenoids and Solenoid Hardware 1 Nitrous bottle bracket set (1
Résumé du contenu de la page N° 8
2.0 Performer System Installations 2.1 Nitrous Bottle Mounting The nitrous oxide storage cylinder is typically called a “nitrous bottle”. It is an aluminum cylinder, designed and manufactured to withstand very high pressures. The valve on top of the bottle is a high-flow design that allows easy opening and closing which controls the nitrous flow to the engine compartment. Accurate calibration of your nitrous system depends on the bottle remaining at a stable temperature. In vehicles (such as Cor
Résumé du contenu de la page N° 9
2.2 Bottle Mounting Instructions Accurate calibration of your nitrous system depends on the bottle remaining at a stable temperature. Choosing the proper location and orientation for your bottle can greatly affect the overall operation of the nitrous system. Please read the entire bottle mounting instruction section before making your final bottle location decisions. 2.3 Bottle Orientation Bottle placement is critical to the performance of your nitrous system. It is important to understand how t
Résumé du contenu de la page N° 10
2.4 Nitrous Bottle Installation After you have determined the location and orientation of the nitrous bottle, use the following procedure to install the bottle: 2.4.1 Street Car Installations 1. Disconnect vehicle’s battery. 2. Determine the location of the bottle within the confines of the rear of the vehicle. 3. Once a mounting location has been determined, raise the vehicle (following all safety practices involved in working on a vehicle from under the vehicle) and verify that there are no fu
Résumé du contenu de la page N° 11
2.5 Nitrous Feed Line Mounting 1. Determine the route your main nitrous feed line will follow. Ensure the path does not route the nitrous feed line too close to the exhaust system, suspension, electrical lines/components or tires. 2. Attach nitrous supply line to bottle. 3. Feed nitrous line along proposed route. 4. Secure nitrous supply line to underside of vehicle. Note: Stainless steel covering of the main nitrous feed line is very abrasive. Shield painted components or sensitive system comp
Résumé du contenu de la page N° 12
2.6.2 Nitrous Solenoids Mounting (Continued) 7. Install solenoid assembly in desired location. 8. Leave all wiring loose for electrical systems installation. 9. Connect main nitrous feed line to inlet fitting (4AN x 1/8 NPT nitrous filter fitting) of the first nitrous solenoid and 3AN 90º lines to 3AN Outlet Flare Tee. Here is a typical EFI solenoid assembly, mounted in the engine compartment of our Mercury Marauder, using a 1/8” NPT Plug non-modified EFI solenoid bracket. Modifications performe
Résumé du contenu de la page N° 13
Nozzle 2 Installation (Continuation) 1. Determine nozzle mounting location in the intake boot just before the throttle body. 2. Remove the intake boot. 3. Wearing safety glasses, drill a 7/16” hole in the intake boot where nozzle placement has been determined. 4. Install the nozzle mounting nut and collar into the intake boot. 90-degree 5. Using Teflon Paste, install the 90º outlet nitrous nozzle Nitrous into the intake boot being sure that the exit is facing into Nozzle Outlet the throttle bod
Résumé du contenu de la page N° 14
3.0 Electrical System Installation 3.1 Nitrous Electrical Components Bill of Materials (BOM) Item # Quantity Description 1 1 ea. Activation microswitch 2 1 ea. Activation microswitch bracket (not shown) 3 2 ea. Activation microswitch mounting nut 4 2 ea. Activation microswitch mounting screw 5 1 ea. 30 amp relay 6 1 ea. Wire harness with integral relay/fuse holder 7 1 ea. Red lighted toggle switch 8 2 ea. 18/22g female spade connector, Nylon insulated 9 2 ea. 14/16g female spade connector, Nylo
Résumé du contenu de la page N° 15
3.3 Nitrous Electrical System Wiring Diagram 11 Switched +12V 12 16 Relay 7 Fuse 5 ON GROUND SUPPLY Arming +12v ACC - Red Socket Switch Battery 11 6 Socket Red 8 White (2) WARNING! 9 10 BLUE DO NOT CONNECT TO THIS TERMINAL Black 14 (2) 13 Microswitch Solenoid Solenoid 15 13 1 13 2 (2) 3 13 4 (2) Fuel Pressure Ground Ground Safety Switch Ground ©2002 Edelbrock Corporation Page 14 of 21 Brochure No. 63-0144 Rev. 9/02 Catalog #70406
Résumé du contenu de la page N° 16
3.4 Nitrous Electrical System Installation Procedures Determine the location of the Relay and Fuse Holder wire harness. Most common installations locate these components inside the driver’s compartment and close to the fuse panel under the dash. You can also mount the Relay and Fuse Holder and harness close to the battery. However, these connectors are water-resistant not waterproof, so care is required when mounting this assembly under the hood of your vehicle. Wire Color System Origin Destina
Résumé du contenu de la page N° 17
3.6 Arming Switch and Installation The arming switch is a red, lighted switch that is a "MASTER" arming switch for your nitrous system. Without it, your nitrous system would be "on" all of the time and capable of engaging anytime you go to wide-open throttle conditions with your vehicle. The switch, when in the "armed" position, is well lit. Therefore, it should be placed in an obvious position well within the line of sight and easy reach of the driver. Please refer to the procedures below for t
Résumé du contenu de la page N° 18
3.7 Microswitch Installation and Wiring (Continued) The bolts used to attach the microswitch have extra length to allow for spacing the microswitch away from the bracket if necessary. After determining the position of the microswitch, we recommend trimming the bolts for a clean installation. Due to the wide variety of throttle linkage combinations in use, it is impossible to supply a microswitch bracket custom-tailored to each application. The universal bracket-supplied will need to be modified
Résumé du contenu de la page N° 19
4.0 Before You Run Your Vehicle Using Your Edelbrock Nitrous System You have just completed the installation of your Edelbrock Nitrous System. It is time to perform some basic system checks to ensure all of the work you have done is correct and ready to operate properly. The following procedure is designed to validate the operation of your nitrous system before operating your vehicle: Note: Before performing steps 1 through 5, make sure that the nitrous bottle is closed and main nitrous supply l
Résumé du contenu de la page N° 20
5.0 Troubleshooting and Routine Maintenance How to use our Troubleshooting Flowchart: The troubleshooting of a nitrous system is basic and straightforward. The symptom chart is divided by symptom, cause and action required. Determine your problem (symptom), identify the potential problem (cause) and correct the problem (action required). Symptom #1… Change in engine speed when nitrous bottle valve is opened. 1. Malfunctioning nitrous solenoid. a. Refer to the section entitled 6.0 Solenoid Inspec
