Résumé du contenu de la page N° 1
SyncMaster 400UX,460UX
LCD Monitor
User Manual
Résumé du contenu de la page N° 2
Safety Instructions Notational Note These safety instructions must be followed to ensure your safety and prevent property damage. Make sure to read the instructions carefully and use the product in the correct manner. Warning / Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment. Notational Conventions Important to read and under- Prohibited stand at all times Disconnect the plug from the Do not disassemble outlet Ground to prevent
Résumé du contenu de la page N° 3
Safety Instructions Do not forcefully bend or pull the power plug and do not place any heavy material on it. • Otherwise, this may result in fire. Do not connect multiple appliances to the same power outlet. • Otherwise, this may cause fire due to overheating. Do not disconnect the power cord while using the product. • Otherwise, this may result in damage to the product due to electric shock. To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, there
Résumé du contenu de la page N° 4
Safety Instructions Do not install it in a badly ventilated location such as a bookcase or closet. • Otherwise, this may result in fire due to an increase in the internal temperature. When putting the product down, make sure to put it down softly. • Otherwise, this may result in damage to the screen display. Do not place the front of the product on the floor. • Otherwise, this may result in damage to the screen display. Ensure that an authorized installation company installs the wall mount. •
Résumé du contenu de la page N° 5
Safety Instructions When cleaning the product, make sure to disconnect the power cord. • Otherwise, it may result in electric shock or fire. When cleaning the product, disconnect the power cord and clean it softly with a dry cloth. • (Do not use chemicals such as wax, benzene, alcohol, thinner, mos- quito repellant, lubricant, or cleaner.) These may change the appear- ance of the product surface and peel off the indication labels on the product. Since the product housing is easily scratched,
Résumé du contenu de la page N° 6
Safety Instructions Do not try to move the monitor by pulling only the wire or the signal cable. • Otherwise, it may fall and result in electric shock, damage to the product or fire due to damage to the cable. Do not lift or move the product back and forwards or right and left while only holding the power cord or signal cables. • Otherwise, it may fall and result in electric shock, damage to the product or fire due to damage to the cable. Make sure that the ventilating opening is not blocked
Résumé du contenu de la page N° 7
Safety Instructions Take a rest for at least five (5) minutes after using the monitor for one (1) hour. This reduces the weariness of your eyes. Do not install it in an unstable location such as an unstable rack or uneven surface or a location exposed to vibrations. • Otherwise, it may fall and cause personal injury and/or damage the product. • If you use the product in a location exposed to vibrations, it may damage the product and result in fire. When moving the product, turn the power off a
Résumé du contenu de la page N° 8
Safety Instructions Do not place the product in a location exposed to direct sunlight or near any heat such as a fire or heater. • This may reduce the lifetime of the product, and may result in fire. Do not drop any objects onto the product or cause any impact to the product. • Otherwise, this may result in electric shock or fire. Do not use a humidifier or kitchen table near the product. • Otherwise, this may result in electric shock or fire. When there is a gas leak, do not touch the produ
Résumé du contenu de la page N° 9
Introduction -- 400UX -- Package Contents Note Please make sure the following items are included with your LCD Display. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Note This stand is not for the Floor Standing Type. Unpacking LCD Display Manuals Quick Setup Guide Warranty Card User's Guide (Not available in all loca- tions) Cables D-Sub Cable Power Cord
Résumé du contenu de la page N° 10
Introduction Others Remote Control Batteries (AAA X 2) BNC to RCA Adaptor Jack (Not available in all loca- tions) Sold separately DVI Cable Wall Mount KIT Semi Stand KIT Calibrater BNC Cable For more information on the use of the calibrater, see Nat- ural Color Expert Help. -- 400UX -- Your LCD Display Front MENU button [MENU]
Résumé du contenu de la page N° 11
Introduction Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu or return to the previous menu. Navigate buttons (Up-Down buttons) Moves from one menu item to another vertically or adjusts selected menu values. Adjust buttons (Left-Right buttons) / Volume buttons Moves from one menu item to another horizontally or adjusts selected menu val- ues. When OSD is not on the screen, push the button to adjust volume. ENTER button [ENTER] Activates a highlighted menu item. SO
Résumé du contenu de la page N° 12
Introduction Note See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your LCD Display OFF when it is not needed or when leaving it unattended for long periods. Remote Control Sensor Aim the remote control towards this spot on the LCD Display. Rear Note For detailed information concerning cable connections, refer to Connecting Cables under Setup. The LCD Display 's configuration at the back may vary slightly depending o
Résumé du contenu de la page N° 13
Introduction REMOTE OUT/IN You can use a wired remote control by connecting it to your LCD Display. RS232C OUT/IN (RS232C Serial PORT) MDC(Multiple Display Control) Program Port DVI / PC / HDMI IN [PC/DVI/BNC AUDIO IN] (PC/DVI/BNC/HDMI Audio Connection Ter- minal (Input)) DVI / PC / HDMI IN [HDMI] Connect the HDMI terminal at the back of your LCD Display to the HDMI terminal of your dig- ital output device using a HDMI cable. DVI / PC / HDMI IN [RGB](PC Video Con- nection Terminal) Using a
Résumé du contenu de la page N° 14
Introduction AV AUDIO IN [L-AUDIO-R] (LCD Display Audio Connection Terminal (Input)) AV OUT [VIDEO](VIDEO Connection Ter- minal) AV mode (Output) AV IN [VIDEO](VIDEO Connection Termi- nal) (Input) AV OUT [S-VIDEO] (S-VIDEO Connection Terminal) S-VIDEO mode (Output) AV IN [S-VIDEO](S-VIDEO Connection Terminal) (Input) EXT SPEAKER(8 Ω)[- - L - +, - - R - +] (EXT Speaker Connection Terminal) AUDIO OUT [L-AUDIO-R] (LCD Display Audio Connection Terminal (Output))AUDIO OUT is the terminal for s
Résumé du contenu de la page N° 15
Introduction ON / OFF MagicInfo MDC LOCK MagicInfo buttons +100 DEL VOL MUTE TTX/MIX MENU ENTER P.MODE AUTO ENTER/PRE-CH CH/P SOURCE INFO EXIT Up-Down Left-Right buttons S.MODE STILL FM RADIO P.SIZE SRS DUAL/MTS PIP SOURCE SWAP SIZE REW STOP PLAY/PAUSE FF 1. ON / OFF Turns the LCD Display On/Off. 2. MagicInfo MagicInfo Quick Launch Button.
Résumé du contenu de la page N° 16
Introduction 3. MDC MDC Quick Launch Button. 4. LOCK Activates or deactivates all function keys on both the remote con- trol and the LCD Display except for the Power and LOCK buttons. 5. MagicInfo buttons MagicInfo Quick Launch Button. • Alphanumeric: Used to enter the Internet address. • DEL: Functions as the backspace. • SYMBOL: Used to enter the symbols. (.O_-) • ENTER: Used to enter values. Press to select channels over 100. For example, to select channel 6. +100 DEL 121, press "+100", then
Résumé du contenu de la page N° 17
Introduction - This fuction does not work for this LCD Display. Changes the video source. 16. SOURCE The current picture information is displayed in the top left corner 17. INFO of the screen. Exits from the menu screen. 18. EXIT 19. Up-Down Left-Right but- Moves from one menu item to another horizontally, vertically or tons adjusts selected menu values. When pressing this button, the current mode is displayed at the 20. S.MODE bottom centre of the screen. The LCD Display has a built-in high
Résumé du contenu de la page N° 18
Introduction Switches the PIP Picture Size. 29. SIZE 30. REW Rewind Stop 31. STOP Play/Pause 32. PLAY / PAUSE 33. FF Fast forward -- 400UX -- Mechanical Layout Mechanical Layout NETWORK MODEL SIZE
Résumé du contenu de la page N° 19
Introduction LCD Display Head NETWORK MODEL SIZE Installation VESA Bracket • When installing VESA, make sure to comply with the international VESA standards. • Purchasing VESA Bracket and Installation Information : Please contact your nearest SAMSUNG Distributor to place an order. After your order is placed, installation professionals will visit you and install the bracket. • At least 2 persons are needed in order to move the LCD Display. • SAMSUNG is not responsible for any product damage or an
Résumé du contenu de la page N° 20
Introduction Dimensions Notice For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12 mm length. Wall Bracket Installation • Contact a technician for installing the wall bracket. • SAMSUNG Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer. • This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood. Components Only use the comp
