Instruction d'utilisation Audiovox Prestige APS-45B

Résumé du contenu de la page N° 1

Model APS-45B
Installation Manual
Keyless Entry System
With Two Auxiliary Outputs
Installation Instructions
This Unit Is Intended For Installation In Vehicles With
12 Volt Negative Ground Electrical Systems Only.
Kit Contents:

(1) Control Module

(2) - Three Button Transmitters

4 Channel Code Learning Receiver

On Board Antenna

(1) - Multi Pin Input/Output Harness

(1) - Three Pin Door Lock Harness

(1) - Two Pin LED Indicator

(1) - Two Pin Valet / Override Switch

(1) - 15 Amp In-

Résumé du contenu de la page N° 2

The APS-45B Keyless Entry System is designed to provide a convenient electronic means to gain access to the vehicle by providing RF remote control over the vehicle's power door lock system. The unit also includes outputs to control the vehicle's dome lights, as well as exterior parking lights. Although not an alarm system, this unit also incudes a starter interrupt circuit output. It also includes two additional auxiliary outputs designed to allow for control over optional devices such as a p

Résumé du contenu de la page N° 3

directly to the vehicle's positive parking light circuit. Once the wire is located, confirm that all the vehicle's parking lights will illuminate when +12VDC is connected to it. NOTE: Some vehicles, (mostly European) have isolated "left" and "right" side parking lights. To connect to the parking light systems in these vehicles, you must use separate SPDT relays to connect to each side in order to keep them isolated. Attach the WHITE wire of the system to this point. BROWN Wire: Negative (-) D

Résumé du contenu de la page N° 4

GREEN/BLACK Wire: Immediate, 300mA Duration of Transmit, Channel 4 OutputThe Green/Black wire supplies a 300mA switched output whenever Channel 4of the receiver is accessed. Pressing A combination of thetransmitter Lock/ UnLock buttons simultaneously will access Channel 4 and will remain active for as long as the transmitter button(s) is held. This is a low current output and must be connected to a relay to supply power to the device you intend to control. Connect Green/Black Trace wire to t

Résumé du contenu de la page N° 5

the red wire to the wire that provides a low current positive signal from the factory door unlock switch to the factory door lock control relay. The green wire provides a positive pulse during locking, or the pulsed + 12 volt lock output. Connect the green wire to the wire that provides a low current positive signal from the factory door lock switch to the factory door lock control relay. 3 Wire Positive Switched 2 Step Door Locks The green wire provides a positive pulse during locking, or the p

Résumé du contenu de la page N° 6

Programmable Features: Features 1 Chirp 2 Chirp 3 Chirps Default First Passive Arming Active Arming Active Arming Second Ignition D/L ON Ignition D/L OFF Ignition D/L OFF Third Ignition D/UL ON Ignition D/UL OFF Ignition D/UL OFF Fourth Chirps ON Chirps OFF Chirps ON Fifth Passive D/L Active D/L Active D/L Sixth Siren Output Horn Output Horn Output Seventh 800ms D/L Pulse 3.5 Sec. D/L Pulse 800ms D/L Pulse 800ms Door Lock Double 800ms D/UL Pulses To Program These Features: Entering the Programmi

Résumé du contenu de la page N° 7

Fourth Turn the valet switch on then off 1 chirp = chirps on 4 Flash pause Press transmitter Lock button to change 2 chirps = chirps off or Fifth Turn the valet switch on then off 2 chirps = active locks 5 Flash pause Press transmitter Lock button to change 1 chirp = passive locks or Sixth Turn the valet switch on then off 2 chirp = horn output 6 Flash pause Press transmitter Lock button to change 1 chirp = siren output or Seventh Turn the valet switch on then off 1 chirp = 800ms door lock outpu

Résumé du contenu de la page N° 8

4 3 © 2001 Audiovox Electronics Corp. 128-6183