Instruction d'utilisation Black & Decker BDV1084

Résumé du contenu de la page N° 1

UK
Ireland
Australia
New Zealand

Résumé du contenu de la page N° 2

2

Résumé du contenu de la page N° 3

Never attempt to remove or replace any parts other than Intended use those specified in this manual. Your Black & Decker battery charger is designed to charge lead-acid batteries. This product is intended for household, Power cord safety consumer use only. Warning! Never alter the ac power cord or plug. If it will not fit, have a proper outlet installed by a qualified electrician. Improper Safety instructions connection may result in an electric shock. Warning! When using mains-powered app

Résumé du contenu de la page N° 4

Make sure that the initial charging rate does not exceed the Do not smoke or have naked flames in the charging area. battery manufacturer's requirement. Follow the instructions for connecting and disconnecting Warning! Risk of explosive gas mixtures. Working in the vicinity the battery charger leads or battery terminals. of a lead-acid battery is dangerous. Batteries generate A marine (boat) battery must be removed and charged on explosive gases during normal battery operation. For this s

Résumé du contenu de la page N° 5

For most automotive and similar applications the battery Connect the positive (red) clamp from the battery charger to charger may be connected to the battery while it is the positive (POS, P, +) post of the battery. connected to the dc circuit. If this is acceptable follow the Connect the negative (black) clamp from the battery charger instructions given in "Charging a battery installed in the to the negative (NEG, N, -) post of the battery. circuit". When disconnecting the battery charger

Résumé du contenu de la page N° 6

Stage 3 - top-off charge will show a circulating pattern on the digital display (2), to indicate that power has been applied. Select the proper Stage 3 is a top-off charge. The voltage is automatically charge current rate based on battery size. regulated and is reduced to a predetermined level while the current is adjusted for a safe, effective battery charge. At the Charging the battery (fig. A) conclusion of stage 3, the appliance will beep, signalling the Press the SLOW/FAST pushbutton

Résumé du contenu de la page N° 7

Part 1 (no load) For estimates of the time it takes to charge a battery, refer to Make sure that there is no load on the alternator by turning the following table: off all the vehicle's accessories. % of charge in the battery The battery must be fully charged before testing the alternator. Rate 75% 50% 25% 0% Run the engine long enough to achieve normal idle speed 2A 7 hrs 14 hrs NR* NR* and verify that there is a no-load voltage. 6A 2.5 hrs 4.7 hrs 7 hrs 9.2 hrs Press the alternator chec

Résumé du contenu de la page N° 8

F01 - Internal shorted cell battery Protecting the environment If the battery being charged has an internal shorted cell, F01 Should you find one day that your appliance needs will be displayed. We recommend taking your battery to a replacement, or if it is of no further use to you, think certified automotive service centre for evaluation. of the protection of the environment. Black & Decker repair agents will accept old Black & F02 - Bad battery connection or battery voltage too low to D

Résumé du contenu de la page N° 9

Technical data Black & Decker repair agents and full details of our after- BDV1084 sales service and contacts are available on the Internet at: Input voltage Vac 230 www.2helpU.com Rated input W 180 Please visit our website www.blackanddecker.co.uk to Output voltage Vdc 12 register your new Black & Decker product and to be kept up Output current A 2/6/10 to date on new products and special offers. Further Weight kg 1.93 information on the Black & Decker brand and our range of products is a

Résumé du contenu de la page N° 10

10

Résumé du contenu de la page N° 11

11

Résumé du contenu de la page N° 12

90507187 06/07