Résumé du contenu de la page N° 1
® TM
MultiSync LCD1560M
Résumé du contenu de la page N° 2
Index Warning .................................................................................................................... 1 Contents ................................................................................................................. 2 Quick Start ............................................................................................................. 3 Controls .............................................................................................................
Résumé du contenu de la page N° 3
WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PL
Résumé du contenu de la page N° 4
Contents ® Your new NEC MultiSync LCD monitor box* should contain the following: ™ • MultiSync LCD1560M monitor with tilt base • Power Cord • Video Signal Cable • Audio Cable • USB Cable • User’s Manual Power Cord Video Signal Cable Audio Cable ® TM MultiSync LCD1560M USB Cable User’s Manual * Remember to save your original box and packing material to transport or ship the monitor. 2
Résumé du contenu de la page N° 5
Quick Start ® To attach the MultiSync LCD monitor to your system, follow these instructions: 1. Turn off the power to your computer. 2. Connect the audio cable to “AUDIO INPUT” on the back of the monitor and the other end to the “Audio out” terminal of the computer (Figure A.1). 3. Remove cable cover. For the PC or MAC with DVI digital output: Connect the DVI signal cable (not included) to the connector of the display card in your system (Figure B.1). Tighten all screws. For the PC with Analog o
Résumé du contenu de la page N° 6
Quick Start –continued Figure A.1 Figure B.2 C.1 4
Résumé du contenu de la page N° 7
Quick Start –continued Cable cover Figure D.1 A Type B Type Figure E.1 Figure F.1 vacation switch power button Figure G.1 5
Résumé du contenu de la page N° 8
Quick Start –continued Tilt and swivel Figure TS.1 Grasp both sides of the monitor screen with your hands and adjust the tilt and swivel as desired (Figure TS.1). Cable Management setup for tilt and swivel Damage can occur to the connection cables if not setup properly while operating the tilt or swivel feature. Please follow these steps to insure the correct cable setup. 1. When setting up your connection cables, be sure to leave the stopper and ferrite core above the cable cover (Figure TS.2
Résumé du contenu de la page N° 9
Quick Start –continued This LCD monitor is designed for use with a flexible arm. Please use the attached screws (4pcs) as shown in the picture when installing. To meet fhe safety requirements, the monitor must be mounted to an arm which guaranties the necessary stability under consideration of the weight of the monitor. The LCD monitor shall only be used with an approved arm (e.g. GS mark). Thickness of Bracket(Arm) 2.0~3.2mm Tighten all screws. 75 75 Specifications If using other screws, check
Résumé du contenu de la page N° 10
Controls ® OSM (On-Screen Manager) control buttons on the front of the monitor function as follows: To access OSM menu, press any of the control buttons ( < , > , –, +, EXIT). To change signal input, press the SELECT button. NOTE: OSM must be closed in order to change signal input. Menu EXIT Exits the OSM controls. Exits to the OSM main menu. < / > Moves the highlighted area left/right to select control menus. Moves the highlighted area up/down to select one of the controls. – / + Moves the bar
Résumé du contenu de la page N° 11
Controls –continued ® AccuColor Control Systems ® AccuColor Control Systems: Six color presets select the desired color setting (sRGB and NATIVE color presets are standard and cannot be changed). R,G,B: Increases or decreases Red, Green or Blue color depending upon which is selected. The change in color will appear on screen and the direction (increase or decrease) will be shown by the bars. NATIVE: Original color presented by the LCD panel that is unadjustable. sRGB: sRGB mode dramatically imp
Résumé du contenu de la page N° 12
Controls –continued Information DISPLAY MODE: Indicates the current display resolution and frequency setting of the monitor. MONITOR INFO.: Indicates the model and serial numbers of your monitor. ® OSM Warning: OSM Warning menus disappear with Exit button. NO SIGNAL: This function gives a warning when there is no signal present. After power is turned on or when there is a change of input signal or video is inactive, the No Signal window will appear. RESOLUTION NOTIFIER: This function gives a war
Résumé du contenu de la page N° 13
Recommended Use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING ® THE MULTISYNC LCD COLOR MONITOR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel. • Do not spill any liquids into the cabinet or use your monitor near water. • Do not insert objects of any kind into the cabin
Résumé du contenu de la page N° 14
Recommended Use –continued CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for warm-up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen. • Position your monitor no closer than 16 inches and no further away than 28 inches from your eyes. Th
Résumé du contenu de la page N° 15
Specifications ® ™ Monitor MultiSync LCD1560M Notes Specifications Monitor LCD Module Diagonal : 15.0 inch Active matrix; thin film transistor (TFT) Viewable Image Size : 15.0 inch liquid crystal display (LCD); 0.297 mm dot 2 Native Resolution (Pixel Count) : 1024 x 768 pitch; 300cd/m white luminence; 450:1 contrast ratio, typical Input Signal Video : ANALOG 0.7 Vp-p/75 Ohms Digital Input: DVI Sync : Separate sync. TTL Level Horizontal sync. Positive/Negative Vertical sync. Positive/Negative Dis
Résumé du contenu de la page N° 16
Features Reduced Footprint: Provides the ideal solution for environments requiring superior image quality but with size and weight limitations. The monitor’s small footprint and low weight allow it to be moved or transported easily from one location to another. ® AccuColor Control Systems: Six color presets select the desired color setting (sRGB and NATIVE color presets are standard and cannot be changed). R,G,B: Increases or de- creases Red, Green or Blue color depending upon which is selected
Résumé du contenu de la page N° 17
Troubleshooting No picture • The signal cable should be completely connected to the display card/computer. • The display card should be completely seated in its slot. • Check the Vacation Switch should be in the ON position. • Front Power Switch and computer power switch should be in the ON position. • Check to make sure that a supported mode has been selected on the display card or system being used. (Please consult display card or system manual to change graphics mode.) • Check the monitor and
Résumé du contenu de la page N° 18
Troubleshooting –continued No Video • If no video is present on the screen, turn the Power button off and on again. • Make certain the computer is not in a power-saving mode (touch the keyboard or mouse). No Sound • Check to see if speaker cable is properly connected. • Check to see if mute is activated. • Check to see if volume in OSM is set at minimum. USB Hub does not operate • Check to make sure the USB cord is properly connected. Refer to your USB device User’s Manual. 16
Résumé du contenu de la page N° 19
References NEC-Mitsubishi Monitor Customer Service & Support Customer Service and Technical Support: (800) 632-4662 Fax: (800) 695-3044 Parts and Accessories/Macintosh Cable Adapter: (888) NEC-MITS [888-632-6487] Customer Service Policies & Processes: http://www.necmitsubishi.com/ css/ServicePolicies/ServicePolicies.htm Online Technical Support Knowledge Base: http://www.necmitsubishi.com/ css/knowledgebase.cfm Customer Service & Technical Support Email: http://www.necmitsubishi.com/ css/tech
Résumé du contenu de la page N° 20
Limited Warranty NEC-Mitsubishi Electronics Display of America, Inc. (hereinafter “NMD-A”) warrants this Product to be free from defects in material and workmanship and, subject to the conditions set forth below, agrees to repair or replace (at NMD-A’s sole option) any part of the enclosed unit which proves defective for a period of three (3) years from the date of first consumer purchase. Spare parts are warranted for ninety (90) days. Replacement parts or unit may be new or refurbished and wil
