Résumé du contenu de la page N° 1
32LD660H 37LD660H 42LD660H
32LD665H 37LD665H 42LD665H
32LV555H 37LV555H 42LV555H 47LV555H 55LV555H
Lodging Guest Interactive Pro:Centric™ TVs
Commercial Mode Setup Guide
Note: Selected features shown in this guide may not be available on all models.
EXPERIENCED INSTALLER
Master TV Setup
pages 11 – 14
Cloning Information
pages 24 – 32
FTG Mode of Operation
pages 33 – 44
© Copyright 2011, LG Electronics U.S.A., Inc. P/N: 206-4200 (Rev B)
Résumé du contenu de la page N° 2
For Customer Support/Service, please call: MODEL and SERIAL NUMBER The model and serial numbers of this TV are located on the 1-888-865-3026 back of the cabinet. For future reference, LG suggests that you record those numbers here: The latest product information and documentation is available online at: Model No._________________ Serial No._______________ www.LGsolutions.com/products WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMO
Résumé du contenu de la page N° 3
IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 17. Power Cord Caution: It is recommended that appliances be placed 2. Keep these instructions. upon a dedicated circuit; that is, a single outlet circuit 3. Heed all warnings. which powers only that appliance and has no additional outlets or branch circuits. Check the specification page 4. Follow all instructions. in the Owner’s Manual to be certain. 5. Do not use this apparatus near water. Periodically examine the cord of your
Résumé du contenu de la page N° 4
IMPORTANT SAFETY INSTRUCTIONS 26. Do not touch the ventilation openings, as they may become (Continued from previous page) hot while the TV is operating. 22. Outdoor Antenna Grounding 27. If you smell smoke or other odors coming from the TV or If an outside antenna or cable system is connected to the hear strange sounds, unplug the power cord, and contact an product, follow the precautions below. authorized service center. An outdoor antenna system should not be located in the 28. Do
Résumé du contenu de la page N° 5
Table of Contents Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Teaching FTG Configuration to a TV . . . . . . . . . . . . . . . 37 Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . 3 – 4 Learning an FTG Configuration File from a TV . . . . . . . 38 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Optional Manual Configuration / TV Setup . . . . . . . . . . . 39 Commercial Mode Overview . . . . .
Résumé du contenu de la page N° 6
Commercial Mode Overview This document describes how to set up LD660H/LD665H and LV555H Pro:Centric™ TVs for Commercial Mode operation. LG commercial TV functionality is based on “ownership” of the Channel Map; that is, the Channel Map resides in the TV’s CPU, Protocol Translator Card (PTC), or embedded b-LAN™ (EBL) module, or it resides externally from the TV (i.e., in a device from the solution provider). Each of these TV models has an EBL module that can be configured either for Pass-thro
Résumé du contenu de la page N° 7
Commercial Mode Overview (Cont.) Cloning Cloning refers to the process of capturing a Master TV Setup and transferring it to a Target TV (both TVs must be in Pass-through Mode). The Master TV’s clonable setup menu options should be configured as part of the Master TV Setup. If there are features in the Master TV’s setup—channel icons or labels, digital font options, etc.—that are not set or that are set incorrectly, those features also will not be set or will be set incorrectly in the Target
Résumé du contenu de la page N° 8
Pro:Centric Operation Pro:Centric TV Interactive Menu Features The interactive Pro:Centric TV enables guests—from the comfort of their hotel rooms—to view and select from a complete listing of hotel services and amenities. The Pro:Centric TV is connected to the hotel's billing computer, and service/amenities charges are billed at the time of order. Interactive amenities may include: • Hotel information, news, and events • Directory services (tourist attractions, restaurants, etc.) • Reservati
Résumé du contenu de la page N° 9
Pro:Centric Operation (Cont.) Pro:Centric Setup The Pro:Centric server provides the following functionality: • Remote management/administration (TV E-Z Installation): The Pro:Centric server Admin Client provides remote management/administration facilities for downloading splash screens and software/firmware updates as well as facilities for downloading FTG Channel Map and FTG Installer Menu settings for TVs that are in FTG Mode via CPU (see also “Remote Management in FTG Mode” on page 7). Th
Résumé du contenu de la page N° 10
Installer Remote Control Typical Key Functions The LG Installer Remote is supplied with and dedicated to operate the TV. The LG Installer Remote illustrated below and throughout this document shows typical remote control functions and is provided for reference only. This Installer Remote may vary from the Installer Remote supplied with the TV. TV/STB/DVD/VCR POWER TV DVD Select the remote’s operating mode: TV, STB, GUIDE DVD, or VCR. STB VCR Displays and removes the electronic GUIDE PORTA
Résumé du contenu de la page N° 11
Master TV Setup This section describes how to set up a Master TV for cloning purposes when the TV is in Pass-through Mode. Note: Refer to FTG Mode information on pages 33 to 44 for details on entering FTG Mode and configuring/editing FTG Channel Map and FTG Installer Menu settings. Before You Begin • Disconnect all Aux inputs if you intend to run Auto Tuning (Channel Search). Under certain conditions, Auto Tuning is disabled if there is an Aux input active. • Determine which cloning tool—US
Résumé du contenu de la page N° 12
Master TV Setup (Cont.) Master TV Setup Procedure 1. Set Installer Menu items. This step provides specific instruction only on the Installer Menu items that should be set on a Master TV. Refer to pages 15 to 22 xxLD66xH PTC INSTALLER MENU for detailed information on all Installer Menu items. a) Make sure the TV is ON. Then, use the Installer Remote to 000 INSTALLER SEQ 000 enter the PTC Installer Menu: Press MENU repeatedly until the on-screen display of the TV setup menus no lo
Résumé du contenu de la page N° 13
Master TV Setup (Cont.) (Continued from previous page) 3. (Optional) Run Auto Tuning. Important: If you intend to use a USB memory device / .tlx file Move Enter CHANNEL for cloning purposes, DO NOT run Auto Tuning. If you Teach Auto Tuning a .tlx file with an auto-tuned/edited Channel Map to a Target Manual Tuning TV, this will put the Target TV in FTG Mode via CPU. If you Channel Edit run Auto Tuning with the intension to clone the resulting Channel Label Channel Map, you must use a USB m
Résumé du contenu de la page N° 14
Master TV Setup (Cont.) (Continued from previous page) 5. Transfer the TV setup menu settings to the commercial controller (PTC): 2-5-5 + MENU Mode Important: This step is essential for successful cloning using a USB memory device / .tll file or a clone programmer. Without this step, the PTC will not contain any of the TV setup menu settings. a) After the TV channel lineup has been edited and channel label icons added, tune to the channel (source) for which you wish to transfer TV setup
Résumé du contenu de la page N° 15
Installer Menu Use the Installer Menu to set up, change, or view operational settings. Refer to the table starting on the next page for brief descriptions of Installer Menu items. More detailed descriptions follow the table listing. Accessing the Installer Menu 1. Make sure the TV is ON. 2. Using an Installer Remote, press MENU repeatedly until the on- xxLD66xH PTC INSTALLER MENU screen display of the TV setup menus (if the TV is in Pass-through Mode) or the Function Menu (if the TV is not
Résumé du contenu de la page N° 16
Installer Menu (Cont.) Installer Menu Items 000 through 073 Menu Function Value Range Default Value Brief Description of Function and Comments Item 000 INSTALLER SEQ 0 ~ 3 0 Leave default set to 0. 001 POWER MANAGE 0 ~ 7 0 Sets number of hours of no activity before automatic shutoff. 002 AC ON 0 / 1 0 Set to 1 to enable Auto Turn ON when AC power is applied. 003 BAND/AFC 0 ~ 3 1 Selects Tuning Band: 0=Broadcast, 1=CATV, 2=HRC, 3=IRC 0 ~ 127, 253, Channel tuned when TV is turned ON. (Set to 255
Résumé du contenu de la page N° 17
Installer Menu (Cont.) Installer Menu Items 075 through 122 Menu Function Value Range Default Value Brief Description of Function and Comments Item 075 REVERT CH 0 / 1 0 If set to 1 and loss of MPI communication occurs, TV tunes to Start Channel. 078 UPN MSB 0 ~ 255 0 User programmable number, most significant byte. 079 UPN MSB-1 0 ~ 255 0 User programmable number, most significant byte - 1. 080 UPN MSB-2 0 ~ 255 0 User programmable number, most significant byte - 2. 081 UPN LSB 0 ~ 255 0 User
Résumé du contenu de la page N° 18
Installer Menu (Cont.) Detailed Descriptions of Installer Menu Items 000 - INSTALLER SEQUENCE 005 - CHAN LOCK (Channel Lock) Channel Lock is ideal if the system must always be on the same Specifies entry sequence to the Installer Menu. channel. Changing channels with the Channel Up/Down or keypad 0 = 9876 1 = 4321 numbers is impossible. Channel Lock is inactive if set to 0 (default). 2 = 1478 3 = 3698 Generally, this feature is used in connection with item 004 STR
Résumé du contenu de la page N° 19
Installer Menu (Cont.) 010 - MUTE DISABLE 023 - CAPTION LOCK Enables or disables sound mute function. If set to 1, sound cannot If set to 0, captions are OFF when the TV is turned ON. Set to 1 to be muted. If set to 0, sound can be muted. use the caption setting configured before the TV was turned OFF when the TV is turned ON. 011 - KEY DEFEAT (Keyboard Defeat) If set to 1, KEY DEFEAT prevents the end user from accessing 028 - CH. OVERIDE (Channel Override) the on-screen menu(s) from the di
Résumé du contenu de la page N° 20
Installer Menu (Cont.) 046 - STRT AUX SRCE (Start Aux Source) 073 - CH NOT AVBLE (Channel Not Available) Sets the starting Aux source. When turned ON, the TV will tune to If set to 1 and item 028 CH. OVERIDE is set to 0, a “NOT AVAIL- starting Aux source if item 004 STRT CHANNEL is set to 0. ABLE” message is displayed when a user direct tunes a channel that is not in the channel scan list available in memory. If item 093 RJP AVAILABLE is set to 0 and item 040 AUTO CAMPORT is set to 0: 075 - RE
