Résumé du contenu de la page N° 3
INFORMATION This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacture’s instructions, may cause or receive unwanted interference. This unit complies with FCC Rules Part 15, which are designed to provide reasonable protection against interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
Résumé du contenu de la page N° 4
IMPORTANT SAFETY INFORMATION 1. Read Instructions – All the safety and operating instructions should be read before the product is operated. 2. Retain Instructions – The safety and operating instructions should be retained for future reference. 3. Head Warnings – All warnings on the product and in the operating instructions should be adhered to. 4. Follow Instructions – All operating and use instructions should be followed. 5. Cleaning – Unplug this product from the wall out
Résumé du contenu de la page N° 5
plug. If the plug still cannot be inserted, contact your electrician to replace your outlet. Do not defeat the safety purpose of the polarized plug. 13. Power-Cord Protection – Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. 14. Outdoor Antenna Grounding – If an outside antenna or cable syst
Résumé du contenu de la page N° 6
21. Replacement Parts – When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards. 22. Safety check - Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. 23. Mount
Résumé du contenu de la page N° 7
Table Of Contents Before You Begin Introduction................................................. 1 Important Safety Information..................... 3 Table of Contents ....................................... 6 Contents of package .................................. 7 Installation Under Cabinet Installation.......................... 8 Countertop/Desktop Installation................ 9 Front Panel Controls................................... 10 Rear Panel Connector
Résumé du contenu de la page N° 8
CONTENTS OF PACKAGE PWR FM/AM TV VOL MUTE CH ENT CH VOL SEEK AP 12 3 DEL ADD 45 6 7 8 9 0 1. VE706 TV 5. Battery (CR2025) 2. Hardware bag 6. FM Dipole Antenna A. 2” Mounting screws (4) 7. Right Angle Coaxial B. 2-1/2” Mounting screws (4) Adaptor C. 3” Mounting screws (4) 8. FM Antenna Adaptor D. Foot (4) 9. AM Antenna E. Hole cap (4) 10. Mounting Hole Template 3. Remote Control 11. Owners / Installation 4. Multi Height Spacer (4) Manual
Résumé du contenu de la page N° 9
UNDER CABINET INSTALLATION 1) Choose an appropriate mounting location underneath a cabinet or shelf. Close proximity to an electrical outlet and a TV antenna or cable connection will facilitate a neat, easy installation. Do not mount the VE706 above a range or oven. Be sure that the location chosen will provide adequate access to the electrical connection on the rear of the unit before continuing. 2) If the location chosen has a bottom edge molding it may be necessary to use t
Résumé du contenu de la page N° 10
COUNTERTOP/DESKT OP INSTALLATION NOTE: Use caution to avoid damaging the LCD screen and the main unit when converting this unit from an under-counter unit to a countertop unit. Leave the protective plastic on the screen until this procedure is completed. 1) Place the unit (with the screen facing up) on a soft padded surface. 2) Pivot the screen so that it is perpendicular to the front of the unit and then turn it sideways. 3) Remove the hinge guide covers (#1) using a flat blade s
Résumé du contenu de la page N° 11
FRONT PANEL CONTROLS 18 19 12:00 VOLUME ON/OFF SET ADD DEL AP TV FM AM P1 P2 P3 P4 MUTE CH SEEK 1 9 2 10 3 11 4 12 13 5 14 6 7 15 8 16 17 19 1) ON/OFF BUTTON – Power ON/OFF. 2) SET BUTTON – Press this button to set the TIME, ALARM, TV Mode. 3) ADD BUTTON – Press this button to add a selected channel. 4) DEL BUTTON – Press this button to delete a selected channel. 5) AP BUTTON – Press and Hold this button to start the Auto Program feature. 6) TV BU
Résumé du contenu de la page N° 12
REAR PANEL CONNECTIONS 1 2 3 4 1) AC LINE CORD – Connects to AC power outlet. 2) FM ANTENNA – Allows the VE706 to be connected to a 75-Ohm external coaxial antenna for the reception of FM broadcast signals. 3) AM ANTENNA - Allows the VE706 to be connected to an external antenna for the reception of AM broadcast signals. 4) TV ANTENNA (75 OHM ANTENNA CONNECTOR) -Allows the VE706 to be connected to a 75- ohm external coaxial antenna or cable TV system.
Résumé du contenu de la page N° 13
LCD Control Functions 1. MENU Button – When pressed, the LCD control MENU is displayed. 2. SEL Button – Used to enter the picture menu. Highlight the menu item to be changed using the UP/DOWN buttons and then press Select to adjust the highlighted item.. 3. UP Button – Scrolls upward through menu items, also adjusts selected item in upward (increase) direction. 4. DOWN Button – Scrolls downward through menu items; also adjusts selected item; in downward (decrease) direction.
Résumé du contenu de la page N° 14
BATTERY INSTALLATION 1) Turn the Remote Control face down. Place a fingernail, or coin in the open slot, slide battery holder out. 2) Install the CR2025 battery into its proper slot. (Note: Be sure to observe the correct polarity when inserting the battery). 3) Slide the battery holder in until it clicks. 13
Résumé du contenu de la page N° 15
REMOTE CONTROL FUNCTIONS 6 7 PWR FM/AM TV 1 8 VOL MUTE 2 CH ENT CH 9 VOL SEEK 10 3 A/P 4 DEL 1 2 3 11 5 ADD 4 5 6 12 7 8 9 0 1. POWER ON/OFF (PWR) Press this button to turn the VE706 on. Press the button again to turn the VE706 off. 2. ENTER (ENT) This button is used after entering the channel number. 3. CHANNEL UP/DOWN ( ) Press these buttons to advance to the next higher or lower channel. 4. AUTO PROGRAM (AP) Press this button for a half secon
Résumé du contenu de la page N° 16
OPERATION Initial Setup: This unit defaults to cable TV mode. When the unit is first powered on, it will detect the cable system and auto-program the TV tuner to the available stations. Please wait while the unit auto-programs before attempting to operate the unit. During this time the unit will not respond to any commands. The unit will respond normally once the cable mode and channel search mode is concluded. CHANNEL TUNING SET UP In addition to normal broadcast receptio
Résumé du contenu de la page N° 1
VE706
LOW PROFILE TELEVISION
INSTALLATION AND OPERATION
MANUAL
• Multi-function Remote Control
• Cable Ready 125 Channel TV Tuner
• Internal Stereo Speakers
• Under Cabinet / Table Top Mounting
• AM/FM Radio Tuner
0
Résumé du contenu de la page N° 2
INTRODUCTION WARNING – To prevent fire or shock hazard, do not expose this unit to moisture. CAUTION: TO REDUCE THE RISK OF ELECTRIC CAUTION SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user to the presence of uninsured “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
Résumé du contenu de la page N° 17
SETTING and ACTIVATING ALARM NOTE: The VE706 must be turned “OFF” when performing the following procedure. 1) Press the SET button twice to enter the alarm mode, press the P3 button to toggle between the active and deactivated mode. NOTE: If a series of dashes appear (--: --), the Alarm is DEACTIVATED. 2) Press the CH up/down buttons to set the desired hour/minute. When setting the alarm, check the AM/PM indicator to assure the proper setting. 3) Press the SEEK buttons to toggle betwee
Résumé du contenu de la page N° 18
SETTING THE AIR TV MODE 1) Press the SET button three times to enter the TV/Cable configuration mode. 2) Press the SEEK button to select the AIR mode. 3) Press the ON/OFF button to confirm. SETTING THE PRESETS (IN AM, FM OR TV MODES) 1) Tune the desired channel/station. 2) Press the SET button and the display flashes. 3) Press desired preset (P1, P2, P3 & P4) to confirm the selection. 17
Résumé du contenu de la page N° 19
TECHNICAL SPECIFICATIONS GENERAL Power Supply AC100-240V ~50/60Hz 25watts Operating Temperature 0°~40°C / 32°~104°F Operating Humidity 10% ~ 75% Body Size 400 X 280 X 56mm / 15.7” x 11.0” x 3.25”Inches Weight 3.2 Kg / 4.2Lbs DISPLAY Illumination CCFL Edge Lit Tube Backlighting Life Expectancy 10,000Hrs Resolution 1440(W) X 234(H) Screen 7” TFT LCD (16:9) MISC TV Channels VHF/UHF (2-69), CABLE TV (STD,IRC,HRC) 1 - 125 TV System NTSC AM 530KHz – 1710KHz Radio
Résumé du contenu de la page N° 20
TROUBLESHOOTING CHECK LIST Problem Solution Poor Reception • Verify Tuner setting matches Antenna/Cable broadcast system. Remote control will not function • Verify that the sensor on the VE706 is not obstructed. • Verify that the infrared LED on the transmitter is not obstructed. • Check the condition of the remote control battery. Black and White Reception • Verify Tuner setting matches Antenna/Cable broadcast system. Try other system types with the instructions on page 1
