Résumé du contenu de la page N° 1
performance by NEXUS NETWORK
Depth transducer TH 52
Installation Manual English
Résumé du contenu de la page N° 2
DEPTH TH52 English 11-1
Résumé du contenu de la page N° 3
English DEPTH TH52 11-2
Résumé du contenu de la page N° 4
DEPTH TH52 English CONTENTS: 1 Applications.........................................................................................................4 2 Tools and Materials Needed ...............................................................................4 3 Mounting Location..............................................................................................5 3.1 Acoustic Noise ..............................................................................................5 3.
Résumé du contenu de la page N° 5
English DEPTH TH52 INSTALLATION INSTRUCTIONS Thru-Hull Depth Transducer Low Profile, Flush, and Retractable Models IMPORTANT: Please read these instructions completely before proceeding with the installation. These directions supersede any other instructions in your instrument manual if they differ. WARNING: NEVER USE SOLVENTS! Certain cleaners, fuel, paints, sealants, and other products may contain strong solvents, such as acetone, which attack many plastics greatly redu
Résumé du contenu de la page N° 6
DEPTH TH52 English 3 Mounting Location 3.1 Acoustic Noise Acoustic noise is always present and these sound waves can interfere with the operation of the transducer. Background noise from sources such as: waves, fish, and other vessels cannot be controlled. However, carefully selecting the transducer mounting location can minimize the affect of vessel generated noise from the propeller(s) and shaft(s), other machinery, and other echosounders. The lower the noise level, the higher the ec
Résumé du contenu de la page N° 7
English DEPTH TH52 3.3 Boat Types (see Figure 1) • Displacement hull powerboat—Locate 1/3 aft LWL and 150–300mm (6–12") off the centerline on the side of the hull where the propeller is moving downward. • Planing hull powerboat—Mount well aft, on or near the centerline, and well inboard of the first set of lifting strakes to insure that the transducer is in contact with the water at high speeds. Mount on the side of the hull where the propeller is moving downward. Outboard and I/
Résumé du contenu de la page N° 8
DEPTH TH52 English 4 Installation Cored fiberglass hull—Follow separate instructions on page 4. 4.1 Hole Drilling Warning: Always wear safety goggles and a dust mask. 1. Drill a 3 mm or 1/8" pilot hole from inside the hull. If there is a rib, strut, or other hull irregularity near the selected mounting location, drill from the outside. Note: If the pilot hole is drilled in the wrong location, drill a second hole in a better location. Apply masking tape to the outside of the hu
Résumé du contenu de la page N° 9
English DEPTH TH52 4.2 Bedding Caution: Never pull, carry, or hold the transducer by its cable; this may sever internal connections. 1. Remove the hull nut and any washer (see Figure 2). Also remove the cap nut and the transducer insert. 2. Apply a 2mm (1/16") thick layer of sealant around the lip of the housing that contacts the hull and up the sidewall of the housing, 6 mm (1/4") higher than the combined thickness of the hull, washer(s), and the hull nut. This will ensure ther
Résumé du contenu de la page N° 10
DEPTH TH52 English tighten only. Do not over tighten. Warning: Always attach the safety wire to prevent the insert from backing out in the unlikely event that the cap nut fails or is screwed on incorrectly. 6. Attach the safety wire. Attach the safety wire to one eye in the hull nut. Lead the wire in a counterclockwise direction and thread it through one eye in the cap nut, the pull ring, the second eye in the cap nut, and the second eye in the hull nut. Twist the wire securely to i
Résumé du contenu de la page N° 11
English DEPTH TH52 5.3 Installation in a Cored Fiberglass Hull The core (wood or foam) must be cut and sealed carefully. The core must be protected from water seepage, and the hull must be reinforced to prevent it from crushing under the hull nut allowing the housing to become loose. Warning: Always wear safety goggles and a dust mask. 1. Drill a 3 mm or 1/8" pilot hole from inside the hull (see Figure 3). If there is a rib, strut, or other hull irregularity near the selected mo
Résumé du contenu de la page N° 12
DEPTH TH52 English 6 CONNECTION TO INSTRUMENT/CONTACTS The depth transducer connects to the FI-30 Server or directly. The transducer cable is clearly marked with No 2 and the colours will correspond to input screw terminal on the Server. IMPORTANT! DO NOT CUT OR EXTEND THE 8 M TRANSDUCER CABLE! 7 Calibration Calibration is carried out in the Multi Control instrument (see manual). 8 Maintenance 8.1 Antifouling Paint Surfaces exposed to salt water must be coated with
Résumé du contenu de la page N° 13
English DEPTH TH52 9 TECHNICAL DATA Dimensions Transducer: 51 x 86 mm (1 5/8” x 3 3/8”) Transducer cable: 8 m (9.9 ft + 26.2 ft) Power supply: 12V DC (10-16V) Power consumption: 0.2 W Depth range: 0.8 - 150 m (3 - 450 ft) at speed up to 30 knots. Accuracy: ± 0.1 % Type of transducer: Piezocrystal 200 kHz Temperature range: Operation -10°C to + 70°C Storage -35°C to +85°C The depth measuring is based on the echos speed in water which is 1.463 m/sec. 11-12
Résumé du contenu de la page N° 14
DEPTH TH52 English 11-13
Résumé du contenu de la page N° 15
English DEPTH TH52 11-14
Résumé du contenu de la page N° 16
DEPTH TH52 English Copyright ©: Silva Sweden AB Kuskvägen 4, 191 62 Sollentuna, Sweden Tel: +46 -(0) 8 - 623 43 00. Fax: +46 -(0) 8 - 92 76 01 www.silva.se 11-15 22418-1 Edition 1
