Résumé du contenu de la page N° 1
THD SATELLITE COMPASS
SC-50
Résumé du contenu de la page N° 2
Y Your our Local Local A Age gent nt//D De eal ale er r 9- 9-52 52 A Ashi shihar hara- a-cho, cho, N Niishi shinom nomiiy ya 662- a 662-8580, 8580, J JAPAN APAN Te Telle ep phone hone : : 0798- 0798-65- 65-2111 2111 Fax Fax 0798- 0798-65- 65-4200 4200 :: FIR FIRS ST E T ED DITION ITION : : F FEB. EB. 2004 2004 A All r ll riig gh ht ts r s re ese ser rv ve ed d. . P Pr rinte inted in J d in Ja apa pan n C C :: J JUN. UN. 15, 15, 2005 2005 P Pub. ub. No. No. O OM ME E- -72510 72510 **000014
Résumé du contenu de la page N° 3
SAFETY INSTRUCTIONS Safety Instructions for the Operator Safety Instructions for the Installer WARNING WARNING WARNING WARNING ELECTRICAL SHOCK HAZARD Turn off the power at the switchboard Do not open the equipment. before beginning the installation. Only qualified personnel Fire or electrical shock can result if the should work inside the power is left on. equipment. Do not install the equipment where it Do not disassemble or modify the may get wet from rain or water splash. equipment
Résumé du contenu de la page N° 4
TABLE OF CONTENTS FOREWORD ..................................................................................................................iv SYSTEM CONFIGURATION ...........................................................................................v EQUIPMENT LIST..........................................................................................................vi SPECIFICATIONS................................................................................................
Résumé du contenu de la page N° 5
2.9.4 Time format............................................................................................................ 2-15 2.9.5 Demonstration mode.............................................................................................. 2-16 2.10 WAAS/DGPS Setup........................................................................................................... 2-17 2.11 OTHERS Menu.............................................................................................
Résumé du contenu de la page N° 6
FOREWORD A Word to the Owner of the SC-50 FURUNO Electric Company thanks you for purchasing the FURUNO SC-50 THD Satellite Compass. (Hereafter, for sake of brevity, we refer to the SC-50 as Satellite Compass.) We are confident you will discover why the FURUNO name has become synonymous with quality and reliability. For over 50 years FURUNO Electric Company has enjoyed an enviable reputation for quality and reliability throughout the world. This dedication to excellence is furthered b
Résumé du contenu de la page N° 7
SYSTEM CONFIGURATION The SC-50 consists of an antenna, a display unit and a processor unit. The tri-antenna system accommodates three antennas/receiver units and is available in a low-profile radome type or open type. The tri-antenna system helps reduce the influence of ship's motion (rolling). Antenna Unit Antenna Unit Display Unit SC-603 SC-303 SC-502 OR 3 Analog pitch 6 ports for Heading or Navigation Data Processor Unit Analog roll (5 AD-10/IEC 61162 ports, 1 AD-10 port) SC-501 Log/Head
Résumé du contenu de la page N° 8
EQUIPMENT LIST Standard supply Name Type Code No. Qty Remarks SC-303 Radome type GPS Antenna Choose one SC-603 Open type Display Unit SC-502 1 Processor Unit SC-50 1 1 CP20-02230* 004-378-110 TPPX cable 1 CP20-02260* 004-379-660 TNC cable CP20-0223 1* 004-378-050 1 For SC-303 For processor unit: CP20-02600 000-04 1-905 1 CP20-0260 1*, Installation MJ-A7SPF0006- 100 Materials For display unit: CP20-02203* 004-380-660 1 Tapping screw (5X20 4 pcs.) CP20-0220 1* 004-37
Résumé du contenu de la page N° 9
THD SPECIFICATIONS OF THD SATELLITE COMPASS SC-50 1 GENERAL 1.1 Heading Accuracy ±1.0° (95%) 1.2 Heading Resolution 0.1° 1.3 Follow-up 45°/s rate-of-turn 1.4 Settling Time 3 minutes 1.5 Position Accuracy 10 m, or 5 m (DGPS), 95% of the time 1.6 Heading/Nav Data Output AD-10 format: 1 port (specialty port) AD-10 format 5 ports or IEC 61162 format 10 ports (selectable on menu) IEC 61162 format is RS-485 level Sentence: HDT, HDM, ROT, ATT, VDR, VTG, GGA, GNS GLL, VHW, VBW, HVE
Résumé du contenu de la page N° 10
4.3 Waterproofing Antenna Unit IPX6 Display Unit IPX5 Processor Unit IPX0 4.4 Vibration IEC 60945 5 COATING COLOR 5.1 Display/Processor Unit Panel: N3.0 Newtone No.5 (dark gray) Chassis: 2.5GY5/1.5 (light gray) 5.2 Antenna Unit N9.5 (white) SP - 2 E7251S01B
Résumé du contenu de la page N° 11
1 INSTALLATION 1.1 Mounting Considerations 1.1.1 Antenna unit General • Keep the length of the antenna cable in mind when selecting a mounting location. Installing the antenna above superstructures • The antenna must be mounted above all other structures on the vessel to obtain an unobstructed view of the satellites regardless of vessel heading. Failure to do so will cause shadows and multipath reflection problems. Mast SC-series Antenna Radar Antenna Bridge Example of antenna
Résumé du contenu de la page N° 12
1. INSTALLATION • The horizontal separation between the antenna and masts must be as follows: Mast diameter Separation distance (minimum) 10 cm 1.5 m 30 cm 3 m SC-50’s antenna Horizontal separation distance Mast, etc. Mast, etc. Less than 10 TOP VIEW Horizontal separation between antenna and masts • The field of view above the antenna should be as shown below, ±80° against zenith. To avoid reflections from masts and the like, locate the antenna well away from the shadows of the ra
Résumé du contenu de la page N° 13
1. INSTALLATION Location influenced Radar Antenna by reflected wave. Reception blocked by mast. SC-series Antenna Bridge Example of antenna installed below superstructures 1.1.2 Display unit, processor unit • Choose a location where vibration and shock are minimal. • Install the units well away from locations subject to rain and water splash. • Locate the units away from air conditioner vents. • Keep the units out of direct sunlight because of heat that can build up inside their ca
Résumé du contenu de la page N° 14
1. INSTALLATION 1.2 Installing the Antenna Unit 1.2.1 Antenna unit SC-303 Note: “Bird-repellent fixtures” (supplied) may be attached to the antenna cover to prevent birds from alighting on the cover. If it is more convenient to attach them before fixing the antenna unit to the mounting location, do step 9 before fixing the antenna unit. NOTICE Fasten the antenna to the mounting location lastly if it is more convenient to connect the antenna cable before mounting the antenna unit. 1. Pr
Résumé du contenu de la page N° 15
1. INSTALLATION 3. Coat exposed parts of nuts, bolts and washers with silicone sealant. Radome base Platform Coat with silicone sealant. Coating bolt, nut and washers with silicone sealant 4. Connect the three coaxial cables coming from the antenna unit to the appropriate coaxial cables on the antenna cable, referring to the table below. Cable from antenna Cable (no. marked on cable) TTPX6-3D2V-15M ANT 1 No color ANT 2 Yellow ANT 3 Red For TNC-PS-3D-15, cable labels are provided fr
Résumé du contenu de la page N° 16
1. INSTALLATION 8. Set the “cable cover” to the antenna base as shown in the figure below. Cable Cover How to insert the cable cover HOW TO REMOVE CABLE COVER Insert slotted-head screwdriver here to remove cable cover. 9. If necessary, attach nine “bird-repellent fixtures” (supplied) to the antenna cover as shown below. Use the paper pattern to position the fixtures. Bird-repellent fixture Antenna unit 10. Follow paragraph 1.6 to set up the equipment. If the status display shows “O
Résumé du contenu de la page N° 17
1. INSTALLATION 1.2.2 Antenna unit SC-603 Note: “Bird-repellent fixtures” (supplied) may be attached to each antenna element and the Antenna Cover to prevent birds from alighting on the antenna. If it is more convenient to attach them before fixing the antenna unit to the mounting location, do step 10 in “Welding the antenna unit” before fixing the antenna unit. Mounting 1. Screw in three antenna elements in the Antenna Base. Remove Antenna Cover and Arm Cover. Antenna Cover 2 Antenn
Résumé du contenu de la page N° 18
1 1. INSTALLATION 4. Making sure each antenna element is correctly oriented, fix each with its nut. Write the corresponding arm number on each coaxial cable, using a magic marker. (When connecting with the coaxial cables from the processor unit it is necessary to match correct antenna element number with coaxial cable color.) Arm [1] 1 Arm [2] 2 Arm [3] 3 5. Temporarily fix the pedestal and support plate to the antenna mast as shown in the illustration below. (The pedestal and support
Résumé du contenu de la page N° 19
1 1. INSTALLATION 7. Orient the antenna unit as shown in the illustration below. BOW Antenna Element 2 A number is inscribed on each antenna arm. PORT This is the antenna element number. Antenna Element 3 The bow mark is between antenna element [1] and [2]. Antenna Element Face the bow mark towards 1 the bow Orienting the antenna unit (top view) NOTICE The antenna unit should be positioned within – 2.5 of the bow. 8. Fasten the Antenna Cover with three screws. Antenna Cover 2 3 Ant
Résumé du contenu de la page N° 20
1. INSTALLATION Welding the antenna unit The antenna unit may be welded to the antenna mast if the satellite status display shows “OK.” 1. Unfasten the coaxial cables and dismount the antenna unit. 2. Weld the pedestal and support plate to the antenna mast. Remove the clamps used to temporarily fasten the pedestal and support plate. 3. Fasten the coaxial cables and fix the antenna unit. 4. Wrap the antenna connector with self-vulcanizing tape and then vinyl tape for waterproofing as s
