Résumé du contenu de la page N° 1
3-207-372-11 (1)
Digital Film Imager
Instructions for Use Page 2
Setup Manual Page 31
This manual is comprised of the Instructions for Use and the Setup Manual.
The Instructions for Use gives the information on how to use the printer for the
routine work.
The Setup Manual gives the system administrator the information needed to setup
the printer and connect it to the network.
UP-DF500
© 2003 Sony Corporation
Résumé du contenu de la page N° 2
For the customers in Canada Owner's Record This unit has been certified according to Standard CSA The model and serial numbers are located at the rear. C22.2 NO.601.1. Record these numbers in the space provided below. For the customers in the U.S.A and Refer to these numbers whenever you call upon your Sony dealer regarding this product. Canada Model UP-DF500 is Non-Patient Equipment. Model No. ____________________ This unit can not be used in the vicinity of patients. Serial No. ___________
Résumé du contenu de la page N° 3
susceptible equipment. Plug this unit and the susceptible equipment into different branch circuit. Consult your dealer. (According to standard EN60601-1-2 and CISPR11, Class B, Group 1) Caution When you dispose of the unit or accessories, you must obey the law in the relative area or country and the regulation in the relative hospital. Warning on power connection Use a proper power cord for your local power supply. Warning on power connection for medical use Please use the following power s
Résumé du contenu de la page N° 4
Instructions for Use Table of Contents Introduction About this Manual .................................................5 System Overview ....................................................5 System Configuration Example ............................6 Location and Function of Parts and Controls .....6 Preparation Supplied Accessories ..............................................8 Assembly ............................................................8 Placing the Unit ..............................
Résumé du contenu de la page N° 5
Introduction Introduction System Overview The UP-DF500 digital film imager is a thermal printer designed to reproduces image data in DICOM format sent via the network. About this Manual The UP-DF500 has the following functions’ Equipped with DICOM (Digital Imaging and Introduction Communications in Medicine) features Describes the features and system configuration of the The DICOM portion of the unit receives image data in digital film imager. Also provided is information on the DICOM fo
Résumé du contenu de la page N° 6
Introduction System Configuration Location and Function Example of Parts and Controls The system allows you to make printouts of the data in For details, refer to the pages given in parentheses. DICOM format, sent from image diagnosis equipment such as CTs, MRIs. Front panel The following shows a system configuration example. Personal computer for DICOM server managing the system DICOM LAN network Modality Image diagnosis equipment and so on Rear panel Modality Image diagnosis equipment and
Résumé du contenu de la page N° 7
Introduction When film is running short: Lights in yellow. N G, g, F, f (Cursor control) buttons (15, 16, 17, When film has been exhausted: Goes off. The 19) ALARM indicator lights in orange and the message Press these buttons to increase or decrease the is displayed in the LCD. setting values. Also press these buttons to select menu items. C PRINT indicator (14, 26) Lights in green while the printer is printing. O MENU button (15, 16, 17, 19) Press these buttons to display menus on the print
Résumé du contenu de la page N° 8
Preparation Assembly Preparation Insert the film tray into the unit. Holding both sides of the film tray and tray cover with both hands, insert the film tray all the way into the unit. Supplied Accessories The unit is packed together with the following accessories. Check that nothing is missing from your package. Film tray (1) Casters for vertical placement of the unit (2) Placing the Unit You can place the unit horizontally or vertically. When placing the unit horizontally To maintain perfor
Résumé du contenu de la page N° 9
Preparation When placing the unit vertically You can place the unit vertically if you attach the casters Connections provided. This is convenient for placing the unit under a desk and to pull it out easily. Connect the unit to the 100BASE-TX LAN. Notes Connect the AC power cord last. Before connecting to the LAN, be sure to set up the required IP address and sub-net mask. For detailed information, consult the system administrator. Before connecting the unit using a 100BASE-TX cable, a
Résumé du contenu de la page N° 10
Preparation How to attach the ferrite cores Before using the unit, attach the supplied ferrite cores for noise prevention. To confirm to radiation standards, attach the supplied ferrite cores to both ends of the cable. Ferrite core Stoppers 12.5 mm (1/2 inch) 12.5 mm (1/2 inch) 1 Release the two stoppers to open the ferrite core. 2 Attach the ferrite cores to the end of the cable about 12.5 mm (1/2 inch) away from the connector. 3 Close the ferrite core until it clicks. 10 Connections
Résumé du contenu de la page N° 11
Operation The film tray is partially ejected. Operation Loading Film Recommended Film The following blue thermal film is made especially for the UP-DF500. Push the EJECT TRAY button UPT-517BL Blue Thermal Film printing pack Contains blue thermal transparent film. 125 sheets of 14 × 17 inch film Be sure to use film made expressly for the UP-DF500. If Notes you use other film, the quality of the printout cannot be You can replace film without pulling out the film guaranteed. Use of another t
Résumé du contenu de la page N° 12
Operation 4 Cut the blank part of the bag from the wedges on 5 Hold the aluminum damp-proof bag with both the bag. hands so that the opened side faces toward the inner side of the tray and place the film in the film tray so that the printing surface faces down, with the printing surface protection sheet on the bottom. Note Remove the seal after loading the film in the film Film tray tray. If you remove it before loading, the film may Face the cut part toward the inner side of the film tray
Résumé du contenu de la page N° 13
Operation roller, pinch roller, and separation rubbers” (on Note page 21). Do not add film halfway through one bag of film. Be sure to check that the hooks of the film tray The reason for this is because the unit counts the cover and its magnets are attached firmly on the remaining film using the IC tag on the printing film tray. If the film tray cover is not closed protection sheet on the bottom. correctly, film placed in the film tray may slide around. 6 Remove the seal from the film pl
Résumé du contenu de la page N° 14
Operation 2 The stored image data is printed. During printing, the PRINT indicator is lit. Printing Before printing Ensure that the unit is properly connected to the LAN. (page 9) Ensure that the film sheets are properly loaded in the film tray. (page 11) It takes about 70 seconds for a printout to LCD emerge from the film outlet. Once printing has been completed, the PRINT indicator goes off, PRINT indicator and the unit returns to READY status. Notes 1 During printing, do not open t
Résumé du contenu de la page N° 15
Adjustment 3 Select the item you want to confirm by pressing the Adjustment F or f button. To display the IP address Select IP ADDRESS. Menu Operation You can set the following items using the relevant menu: Confirming information (INFORMATION) (page 15) Adjusting the print quality (PRINT QUALITY) (page 15) IP address Calibration (CALIBRATION) (page 16) Adjusting the density (DENSITY ADJ) (page 17) Note Selecting a gamma curve (GAMMA SEL) (page 19) You can change the IP address using
Résumé du contenu de la page N° 16
Adjustment The unit enters the sharpness adjustment mode. 2 Display the CALIBRATION menu by pressing the F or f button, then press the g button. The calibration menu is displayed. The unit enters the automatic calibration mode. 3 Select the desired level by pressing the G or g button. 3 Select the desired calibration type by pressing the F or f button. To calibrate the unit 1 Display FULL RANGE CAL by pressing the F Current sharpness or f button. The sharpness can be adjusted among 15 levels
Résumé du contenu de la page N° 17
Adjustment 1 Display LIMITED CAL, by pressing the F or f Adjusting the Tone button. You can adjust the high tone (dark areas of the images) and the low one (light areas of images). 1 3 5 2 Select ON by pressing the G or g button. Display ON in capital letters by pressing the G or g 24 button. 1 Press the MENU button. To reset to the default status If you reset to the default status, the calibration is 2 Display the DENSITY ADJ menu by pressing the not performed by selecting FULL RANGE CAL.
Résumé du contenu de la page N° 18
Adjustment The unit starts the printing of the tone pattern. 3 Display the selected number by pressing the G or g button. Display the selected number. To reset to the default setting of the low tone range Display 25. To adjust the high tone Select the way the dark areas of images will be printed. 1 Display SELECT POINT 5% by pressing the F 5 Adjust the tone while checking the pattern print. or f button. To adjust the low tone Select the way the light areas of images will be printed. 1 Displ
Résumé du contenu de la page N° 19
Adjustment 3 Display the selected number by pressing the G Gamma curve Meaning or g button. SONY 1 Default setting SONY 2 The half tone is darker compared to SONY 1 SONY 3 The half tone is lighter compared to SONY 1 Display the selected number. SONY 4 The half tone is smoother compared to SONY 1 SONY 5 The half tone is sharper compared to SONY 1 To reset to the default setting of the high tone range USER 6 to 10 Not preset. For advice on settings, Display 75. contact your nearest Sony dea
Résumé du contenu de la page N° 20
Miscellaneous film tray. This will cause the printer to malfunction. Miscellaneous Also, if the film is used in this state, spots are likely to appear on the printout. To store a half-used package of film, replace the film in its original packing and reseal the package. If possible, before using sealed film, place it, in its Precautions sealed package, in a warm room for several hours. Doing so prevents condensation from forming when the film is removed from its package. Safety Operat
