Résumé du contenu de la page N° 1
Power
06-18-10
SWI-RC
Universal Steering Wheel Control Interface
For Alpine, JVC, Clarion, Kenwood,
Pioneer, Sony, Valor, OEM, Boyo,
Installation Instructions
Dual, Visteon, Advent & Blaupunkt
Pacific Accessory Corporation
Steering Remote Ready Radios
Before You Start
A. Is this product compatible with the vehicle?
• Please visit http://www.pac-audio.com/swixprogramming/swixprogramming.asp for the most current list of
compatible vehicles.
B. Prepare for the installation.
• If possible, ins
Résumé du contenu de la page N° 2
Step 1 - Wiring Note: Only 3 wires from the SWI-RC will be used during installation. GM vehicles programmed for version #4, will use 4 wires. Step A. Connect the BLACK wire to ground (-). Verification: Wire or location registers a constant (-) when probed. SWI-RC Step B. Connect the RED wire to switched +12V. Verification: Wire registers +12V when the ignition key is turned to the ACC or ON positions. Step C. Connect the appropriate interface control input wire (WHITE, YELLOW, ORANGE or GRE
Résumé du contenu de la page N° 3
7 6 5 4 SWI-RC SWI-RC SWI-RC SWI-RC SWI-RC SWI-RC SWI-RC 3 06-18-10 Step 2 - Programming the Version # Step A. Refer to The Vehicle Application Guide or www.pac-audio.com/swixprogramming/swixprogramming.asp for the proper version number. Refer to the programming chart on page 4 for the proper radio select switch setting. Fill in the information below for quick reference. Please note that it is very important to set the radio select switch before turning on the ignition beginning prog
Résumé du contenu de la page N° 4
SWI-RC SWI-RC SWI-RC SWI-RC SWI-RC SWI-RC Step 3 - Programming the SWI to Learn Steering Wheel Control Functions The SWI-RC must be programmed in the specific order shown in the chart below. If you come across a command in the chart that your 6/18/2010 - 11:41 AM swi-rc radio and button chart.xls steering wheel does not have, or you do not want to program, press the Program Button on the side of the SWI interface. The LED will flash once rapidly and then stay on confirming that you have succes
Résumé du contenu de la page N° 5
SWI-RC SWI-RC SWI-RC SWI-RC SWI-RC SWI-RC SWI-RC 06-18-10 Programming the SWI-RC to Control the Head Unit (cont.) Once programming is completed, wait 7 seconds. Step G. The LED will flash three times After all buttons are indicating end of programming. programmed The Interface will then flash the vehicle version number it was programmed for. Testing the SWI-RC A. When testing the audio controls, the left LED on the SWI-RC will flash indicating it is sending a command. If any function do
Résumé du contenu de la page N° 6
SWI-RC SWI-RC SWI-RC SWI-RC SWI-RC Appendix A. (Continued) Step F. Repeat Steps D and E, using the TEMP DOWN Button. Step G. If the vehicle is equipped with FAN UP and FAN DOWN buttons: Repeat Steps D and E for these buttons as well. In either case, the LED will flash once Step H. and stay on. If the vehicle is NOT equipped with FAN UP and FAN DOWN buttons: Press and release the programming/ mode button on the SWI-RC. Step I. The LED will turn off Within 7 seconds, press and during this pro
Résumé du contenu de la page N° 7
06-18-10 Appendix B: Vehicle Exception Notes Vehicle Make Year/Model Description 2002-2008 A4/S4 Audi The SWI-CAN must also be used 2002-2005 A6/S6 All with 5-Volt SWC data wire at the steering column BMW All All with factory activated cellular phones 2003-2004 C230 2003-2004 CLK The SWI-CAN must also be used 2003-2004 CLK 320 200-2002 CLK Mercedes 2007 CLK 350 200-2007 E The SWI-CAN2 must also be used 2008 GL 2001-2003 S 2006 SLK Mitsubishi 2006-2007 Raider The SWI-CAN2 must also be used The SW
Résumé du contenu de la page N° 8
Troubleshooting Guide My Vehicle is not listed in the Identification and Connection Chart: • Please visit http://www.pac-audio.com/swixprogramming/swixprogramming.asp for the most up to date listing of compat- ible vehicles. I cannot program the INTERFACE version number: • Is the radio selection switch in position “0”? If so refer to page 5 and select a radio position before attempting to program a version number. No power / won’t go into programming mode: • Check Red wire connection and fus
