Instruction d'utilisation Metra Electronics 99-8218

Résumé du contenu de la page N° 1

INSTALLATION INSTRUCTIONS FOR PART 99-8218
APPLICATIONS
TOYOTA
CAMRY / CAMRY HYBRID
2007-2011
99-8218
KIT FEATURES
• DIN Radio Provision with Pocket
• ISO Radio Provision with Pocket
• Double DIN Radio Provision
• Stacked ISO Units Provision
KIT COMPONENTS
A) Radio Housing • B) Radio Housing Brackets • C) ISO Snap-In Brackets • D) Double DIN Brackets
E) Trim Plate • F) Double DIN Trim Plate • G) Pocket • H) (4) # 8 x 3/8 Phillips Screws • I) (4) #4 x 1/4 Phillips Screws
B
E

Résumé du contenu de la page N° 2

99-8218 TABLE OF CONTENTS Dash Disassembly - Toyota Camry / Camry Hybrid 2007-2011 . . . . . . . . . . . . 1, 2 Kit Assembly - DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . 3 - ISO Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . 4 - Double DIN Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - Stacked ISO Units Provision . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Final Assembly ..................................

Résumé du contenu de la page N° 3

1 2 4 5 6 3 1 2 6 3 4 5 1 2 3 4 5 6 99-8218 DASH DISASSEMBLY TOYOTA CAMRY/CAMRY HYBRID 2007-2011 A Disconnect the negative battery terminal 1 to prevent an accidental short circuit. 2 Turn the shift knob counterclockwise to remove. 3 Unclip and remove (1) trim panel from each side of the pocket below the radio/climate control assembly. (2 panels total) (Figure A) B 4 Unclip and remove the shift knob trim panel. (Figure B) 5 Unclip and remove the top of the center console including the cup holde

Résumé du contenu de la page N° 4

1 2 4 5 6 3 1 2 3 4 5 6 DASH DISASSEMBLY 99-8218 TOYOTA CAMRY / CAMRY HYBRID 2007-2011 A 8 Unclip and remove the A/C vents above the radio. (Take care not to scratch the dash panel. (Figure A) 9 Remove (2) 10mm bolts above the radio (behind the A/C vents) and (2) 10mm bolts below the climate controls (behind pocket) then unplug and remove the radio/climate control assembly. B (Figure B) 10 Remove the (10) Phillips screws securing the brackets to the radio/climate control assembly and separate t

Résumé du contenu de la page N° 5

99-8218 KIT ASSEMBLY DIN RADIO PROVISION WITH POCKET A NOTE: Refer also to the instructions included with the aftermarket radio. Slide the DIN cage into the Radio 1 Housing and secure by bending the metal locking tabs down. (Figure A) B Slide the after-market radio into the 2 cage until it snaps into place. (Figure B) Snap the pocket into the radio 3 housing. (Figure B) Align the small legs on the bottom 4 C of the radio housing with the slots in the top of the climate control. Then slide the cl

Résumé du contenu de la page N° 6

99-8218 KIT ASSEMBLY ISO RADIO PROVISION WITH POCKET A NOTE: Refer also to the instructions included with the aftermarket radio. Mount the ISO Brackets to the 1 radio with the screws supplied with the radio. (Figure A) Slide the radio into the radio open- 2 B ing until the side clips engage. (Figure B) Snap the Trim plate into the Radio 3 Housing. (Figure B) Snap the pocket into the radio 4 housing. (Figure B) Align the small legs on the bottom 5 C of the radio housing with the slots in the top

Résumé du contenu de la page N° 7

99-8218 KIT ASSEMBLY DOUBLE DIN A RADIO PROVISION NOTE: Refer also to the instructions included with the aftermarket radio. Cut and remove center divider 1 from radio housing. (Figure A) B Snap the Double DIN brackets to the 2 inside edge of the radio housing. (Figure B) Slide the Double DIN radio into the 3 Double DIN bracket/radio housing assembly and secure the radio to the C assembly using the screws supplied with the radio. (Figure C) Snap the Double DIN trim-plate into 4 the housing/radio

Résumé du contenu de la page N° 8

99-8218 KIT ASSEMBLY STACKED ISO A UNITS PROVISION NOTE: Refer also to the instructions included with the aftermarket radio. Cut and remove center divider 1 from radio housing. (Figure A) B Snap the Double DIN brackets to the 2 inside edge of the radio housing. (Figure B) Slide the Stacked ISO units into the 3 Double DIN bracket/radio housing assembly and secure the radio to the C assembly using the screws supplied with the units. (Figure C) Snap the Double DIN trim-plate into 4 the housing/rad

Résumé du contenu de la page N° 9

99-8218 FINAL ASSEMBLY FINAL ASSEMBLY A A) Strip wire ends back 1/2" B B) Twist ends together C) Solder C D) Tape D Locate the factory wiring harness in the dash. Metra recommends using the 1 proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. Reassemble radio and dash assemblies in reverse order of disassem

Résumé du contenu de la page N° 10

99-8218 NOTES 8

Résumé du contenu de la page N° 11

99-8218 NOTES 9

Résumé du contenu de la page N° 12

99-8218 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV. 07-22-10 © COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION INST99-8218