Instruction d'utilisation Metra Electronics 99-7861

Résumé du contenu de la page N° 1

INSTALLATION INSTRUCTIONS FOR PART 99-7861
APPLICATIONS
Honda Pilot
•2003-2008
•2006-2008 (Without Factory Navigation)
99-7861
KIT FEATURES
• Recessed DIN
• Pocket
• ISO Head Unit Provision With Pocket
KIT COMPONENTS
A) “L” Radio Housing • B) “E” Radio Housing • C) Pocket • D) Rear Support Bracket • E) ISO Brackets
F) ISO Trimplate • G) (2) # 8x3/8” Phillips Truss Head Screws H) (2) # 8x3/8” Phillips Pan Head Screws
B
A C
D G
E F
H
WIRING AND ANTENNA CONNECTIONS (Sold Separate

Résumé du contenu de la page N° 2

99-7861 TABLE OF CONTENTS Dash Disassembly Honda Pilot 2003-2008. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Honda Pilot 2006-2008 (Without Factory Navigation) . . . . . . . . . . 2 Kit Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 DIN Head Unit Provision With Pocket . . . . . . . . . . . . . . . . . . . . . . 4 ISO Head Unit Provision With Pocket . . . . . . . . . . . . . . . . . . . . . . 5 Final Assembly . . . . . . . . . . . .

Résumé du contenu de la page N° 3

DASH DISASSEMBLY 99-7861 HONDA PILOT 2003-2008 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Using a small flat blade screwdriver remove the blank plate from upper right side of radio trim panel. (Figure A) 3 Unsnap radio trim panel. Unplug switches and remove panel. B (Figure B) 4 Remove (4)10mm bolts securing radio, unplug and remove radio. (Figure C) C 1

Résumé du contenu de la page N° 4

DASH DISASSEMBLY 99-7861 HONDA PILOT 2006-2008 (Without Factory Navigation) A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Remove (2) screws from the top of the instrument panel trim. Unclip and remove the instru- ment panel trim. (Figure A) Unclip and remove the left center 3 trim panel. (Figure B) B 4 Unclip the radio trim panel. Unplug and remove the panel. (Figure C) 5 Remove the (4) screws securing the radio. Unplug and remove the radio. (Figure D)

Résumé du contenu de la page N° 5

KIT ASSEMBLY 99-7861 HONDA PILOT •2003-2008 •2006-2008 (Without Factory Navigation) 1 Select the proper radio housing for A your vehicle. EX models use radio housing (E) and LX models use radio housing (L). The radio housings are labeled on one of the mounting tabs. (Figure A) 2 Mount the pocket to the back of the radio housing with the (2) #8x3/8” phillips pan head screws supplied. (Notches on the pocket must be on top.) (Figure B) B 3 Mount the rear support bracket to the back of the pocket wi

Résumé du contenu de la page N° 6

KIT ASSEMBLY 99-7861 DIN HEAD UNIT PROVISION WITH POCKET A 1 Slide DIN cage (supplied with radio) into the assembled radio housing from the front. (Figure A) 2 Secure DIN cage to radio housing by bending the locking tabs outward. (Figure A) Slide the radio into the DIN cage 3 until it snaps into place. (Figure B) B 4

Résumé du contenu de la page N° 7

KIT ASSEMBLY 99-7861 ISO HEAD UNIT PROVISION WITH POCKET A 1 Align the holes in the ISO brackets with the holes in the radio. Mount the brackets to the radio using screws supplied with the radio. (Figure A) 2 Slide the radio/bracket assembly into the assembled radio housing until it snaps into place. (Figure B) Snap the ISO trimplate onto the front 3 B of the assembled radio and housing. (Figure B) NOTE: To remove the radio unsnap and remove the ISO trimplate. Using a flat blade screwdriver dise

Résumé du contenu de la page N° 8

FINAL ASSEMBLY 99-7861 FINAL ASSEMBLY A A) Strip wire ends back 1/2" B B) Twist ends together C) Solder C D) Tape D Locate the factory wiring harness in the dash. Metra recommends using the 1 proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. Reassemble radio and dash assemblies in reverse order of disassem