Résumé du contenu de la page N° 1
INSTALLATION INSTRUCTIONS FOR PART 99-7519B
APPLICA TIONS
Mazda MX-5 Miata
2 0 0 9 - 2 0 1 0
99-7519B
KIT FEATURES
• DIN Head Unit Provision with pocket
• ISO DIN Head Unit Provision with pocket
• Double DIN Head Unit Provision
• Stacked ISO DIN Head Unit Provision
• Painted Matte Black to Match Factory
KIT COMPONENTS
A) Radio Housing • B) Snap-In Pocket • C) ISO Brackets • D) ISO Trim Plate • E) Double DIN Brackets
• F) Double DIN Trim Plate • G) (4) Panel Clips
D
C
B
E F
Résumé du contenu de la page N° 2
99-7519B TABLE OF CONTENTS Dash Disassembly ....................................................................... 1-3 Kit Preparation ............................................................................... 4 Kit Assembly: DIN Head Unit Provision.................................................................. 5 ISO DIN Head Unit Provision........................................................... 6 Double DIN Head Unit Provision..................................................... 7
Résumé du contenu de la page N° 3
DASH DISASSEMBLY 99-7519B MAZDA MX-5 MIATA 2009-2010 A 1 Unclip panel below steering column and remove. (Figure A) 2 Remove (4) Phillips screws from metal brace below steering column and remove. (Figure A) 3 Looking at the side of the radio/cli- mate control panel from underneath the steering column opening, remove (1) 10mm bolt from the side of the radio chassis. (Figure B) B 4 With the center console lid closed unclip and remove the cover on the back side of the center console and remove the
Résumé du contenu de la page N° 4
DASH DISASSEMBLY 99-7519B MAZDA MX-5 MIATA 2009-2010 E 6 Unclip, unplug and remove the entire center console. (Figure E) F 7 Remove the (2) Phillips screws securing the side panels from each side of the radio/climate control panel. (Figure F) G 8 Carefully remove the side panels from each side of the radio/climate control panel by pulling straight back towards the rear of the car. (Figure G) 2
Résumé du contenu de la page N° 5
DASH DISASSEMBLY 99-7519B MAZDA MX-5 MIATA 2009-2010 H 9 Remove (2) Phillips screws, (1) on each side, from the side of the radio/climate control panel. (Figure H) I 10 Pull radio/climate control panel out, disconnect plugs and remove. (Figure I) J 11 Turn the radio/climate control panel over and remove the (4) screws that hold the climate control to the bezel, then remove the climate control. (Figure J) 3
Résumé du contenu de la page N° 6
KIT PREPARATION 99-7519B MAZDA MX-5 MIATA 2009-2010 A 1 Attach the (4) Panel Clips to the posts on the back of the radio housing. (Figure A) 4
Résumé du contenu de la page N° 7
99-7519B KIT ASSEMBLY DIN HEAD UNIT PROVISION A 1 Turn over the 99-7519B housing, take the climate control and screws removed from the factory panel and attach the climate control to the kit housing using the factory screws. (Figure A) B 2 Slide the pocket into the bottom section of the kit housing. (Figure B) C 3 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure C) D 4 Slide the aftermarket head unit into the cage and secure. (Figure D) 5
Résumé du contenu de la page N° 8
99-7519B KIT ASSEMBLY ISO DIN HEAD UNIT PROVISION A 1 Turn over the 99-7519B housing, take the climate control and screws removed from the factory panel and attach the climate control to the kit housing using the factory screws. (Figure A) B 2 Slide the pocket into the bottom section of the kit housing. (Figure B) C 3 Mount the ISO Brackets to the head unit with the screws supplied with the unit. (Figure C) 4 Slide the head unit into the radio opening until the side clips engage. (Figure D) D 5
Résumé du contenu de la page N° 9
99-7519B KIT ASSEMBLY DOUBLE DIN HEAD UNIT PROVISION A 1 Turn over the 99-7519B housing, take the climate control and screws removed from the factory panel and attach the climate control to the kit housing using the factory screws. (Figure A) 2 Cut the rib in the middle of the 99- 7519B housing to make room for the DDIN brackets. (Figure A) B 3 Slide the appropriate DDIN bracket into the kit housing. (Figure B) C 4 Slide the DDIN radio unit into DDIN brackets and secure the unit to the kit usin
Résumé du contenu de la page N° 10
99-7519B KIT ASSEMBLY STACKED ISO DIN HEAD UNIT PROVISION A 1 Turn over the 99-7519B housing, take the climate control and screws removed from the factory panel and attach the climate control to the kit housing using the factory screws. (Figure A) 2 Cut the rib in the middle of the 99- 7519B housing to make room for the DDIN brackets. (Figure A) B 3 Slide the appropriate DDIN bracket into the kit housing. (Figure B) C 4 Slide the stacked ISO DIN units into the DDIN bracket assembly and secure t
Résumé du contenu de la page N° 11
99-7519B FINAL ASSEMBLY FINAL ASSEMBLY Locate the factory wiring harness in the dash and make the connection as shown. 1 Metra recomends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disassembly. FINAL WIRING CONNECTIONS Make wiring connections using the EIA
Résumé du contenu de la page N° 12
99-7519B INSTRUCTIONS 1-800-221-0932 www.metraonline.com © COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION INST99-7519B REV. 09/29/10
