Résumé du contenu de la page N° 1
HIGH DEFINITION RECEIVER / RECORDER
Model : NHD-3000PVR
Résumé du contenu de la page N° 2
USER’S MANUAL HIGH DEFINITION RECEIVER / RECORDER Model : NHD-3000PVR
Résumé du contenu de la page N° 3
Warnings 01 The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNI
Résumé du contenu de la page N° 4
Warnings 01 7. Water and Moisture : Do not use the product near water - for example, near a bath tub, wash bowl, kitchen sink, or laundry tub ; in a wet basement ; or near a swimming pool ; and the like. 8. Accessories : Do not place this product on an unstable table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the man
Résumé du contenu de la page N° 5
Warnings 01 b) If liquid has been spilled, or objects have fallen into the product. c) If the product has been exposed to rain or water. d) If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an importer adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. e) If the product has be
Résumé du contenu de la page N° 6
Table of Contents 02 01. Warnings 1 02. Table of Contents 4 03. Supplied Accessories 6 04. Controls Front Panel Controls and LEDs 7 Rear Panel Connectors 8 Battery Installation for Remote Control 10 05. Installation Antenna Input 11 Connection to Digital TV (YPbPr) 12 Connection to Digital TV (RGB/HV) 13 Connection to RGB PC Monitor 14 Connection to Digital TV (HDMI/DVI) 15 Connection to HDMI/DVI PC Monitor 16 Connection to Analog TV (Composite/S-Video) 17 Connection to Digital Audio Amplifier
Résumé du contenu de la page N° 7
Table of Contents 02 Teletext 34 PIP Control 35 08. Channel Channel Edit 36 Channel Scan 37 Manual Scan 38 Channel Sorting 39 Channel Duplication 40 Parental Rating 41 09. Audio/Video HDMI Video 42 HDMI Audio 43 Monitor Setup 44 Digital Audio Out 45 PIP Size 46 Vol. Control 47 10. PVR Manager Program List 48 Skip Time 49 HDD Sleep Time 50 HDD Format 51 11. System Opacity 52 Time Zone 53 Daylight Saving 54 Sleep Timer 55 New Password 56 Factory Default 57 About 58 12. Specifications 59 Manufactu
Résumé du contenu de la page N° 8
Supplied Accessories 03 Make sure the following accessories are provided with product. 1. Remote Control 4. Component Video Cable 5. Audio Cable(L/R) 2. Batteries (size AAA) 6.HDMI Cable 3. User’s Guide 7. RF Loop Cable 6 Supplied Accessories
Résumé du contenu de la page N° 9
Front Panel Controls and LED’s 04 Remote Control Sensor Front Display STANDBY Power & Remote Indicator LED Timeshift Playback Indicator LED Recording Indicator LED MENU OK EXIT POWER Arrow Buttons Front Side Front Display Power On Channel number is displayed. C100 means digital channel number is 100. A200 means radio channel number is 200. Power Off Clock is displayed. LED Indicators STANDBY STANDBY Power & Remote Sensor Indicator LED. During the period from STANDBY to ON condition, the STANDBY
Résumé du contenu de la page N° 10
Rear Panel Connectors 04 Antenna Input HDMI/DVI Output Power Cord A/V Output Optical Audio Output Service Port Rear Side Note. Connection of input/output connector in rear panel should be done while power is OFF. Power Cord Connect to the AC power (AC 240 ~ 250V / 50Hz). Antenna Input Connect the cable from an off-air TV antenna to Antenna1 input. Connect Antenna1 loop out to Antenna2 input with RF loop cable. Controls 8
Résumé du contenu de la page N° 11
Rear Panel Connectors (Cont.) 04 A/V Output The ‘A/V output’ consists of the followings : Y, Pb, Pr : Component video output (576i, 576p, 720p, 1080i) RGB/HV : RGB, PC monitor output (576p, 720p, 1080i) HDMI/DVI : HDMI/DVI output (576p, 720p, 1080i) Video or S-Video : Composite video or S-Video output (576i) L, R : Analog audio output COAXIAL : Digital audio output (Coaxial) OPTICAL : Digital audio output (Optical) Service Port The service port is for maintenance and software upgrade in the futu
Résumé du contenu de la page N° 12
Battery Installation for Remote Control 04 Remove the battery cover and install batteries like the diagram below. 1. Unlatch the battery compartment cover on the back of remote control. 2. Insert 2 AAA batteries as shown, making sure the + and - ends of each battery line up with the corresponding marks in the battery compartment. 3. Snap the cover back to the remote control. Controls 10
Résumé du contenu de la page N° 13
Antenna Input 05 THE RF LOOP CABLE MUST BE CONNECTED, OTHERWISE THE UNIT WILL NOT BE ABLE TO TUNE. Connecting Antenna Connect the antenna or RF cable wire directly to ANTENNA1 IN and connect ANTENNA1 Loop Out to ANTENNA2 Input by using RF loop cable. NOTE The STB(Set Top Box) should be unplugged before connecting antenna. (Power OFF mode) The RF OUT from the tuner will only work when the unit turns on. It will not give RF OUT during STANDBY mode. 11 Installation
Résumé du contenu de la page N° 14
Connection to Digital TV (YPbPr) 05 < Digital TV > Connect the Video Cables Connect a video cable between the Component video output(Y : Green, Pb : Blue, Pr : Red) jacks of the STB(Set Top Box) and the Component input jacks on the Digital TV according to corresponding colour. On the Video Out Mode, select YPbPr as Video Output Type and select one of 1080i, 720p, 576p, 576i as Video Output Resolution according to your digital TV. NOTE By pressing the remote, V-OUTPUT (2 buttons), you will be
Résumé du contenu de la page N° 15
Connection to Digital TV (RGB/HV) 05 < Digital TV > Connect the Video Cables Connect the RGB/HV output jack of the STB to the RGB input jack of the PC RGB input on the digital TV. In regard to the Video Out Mode, select RGB as Video Output Type and select one of 1080i, 720p, 576p as Video Resolution according to your digital TV. NOTE By pressing the remote, V-OUTPUT (2 buttons), you will be able to change the output ‘YPbPr’ and ‘RGB’. (YPbPr selection is usually used for Component Input, whi
Résumé du contenu de la page N° 16
Connection to RGB PC Monitor 05 Connect the Video Cables Connect RGB/HV video output jack of the STB to the RGB jack of the PC monitor. In regard to the Video Out Mode, select RGB as Video Output Type and select one of 1080i, 720p, 576p according to Video Output Resolution of your PC monitor. NOTE By pressing the remote, V-OUTPUT (2 buttons), you will be able to change the output ‘YPbPr’ and ‘RGB’. (YPbPr selection is usually used for Component Input, while RGB selection is usually used fo
Résumé du contenu de la page N° 17
Connection to Digital TV (HDMI/DVI) 05 < Digital TV > Connect the HDMI Cable Connect the HDMI/DVI output jack of the STB to the HDMI input jack of the digital TV. In regard to the Video Out Mode, select one of 1080i, 720p, 576p as Video Resolution according to your digital TV. NOTE By pressing the remote, V-OUTPUT (2 buttons), you will be able to change the output ‘YPbPr’ and ‘RGB’. (YPbPr selection is usually used for Component Input, while RGB selection is usually used for PC/HDMI Input)
Résumé du contenu de la page N° 18
Connection to HDMI/DVI PC Monitor 05 Connect the Video Cables Connect HDMI/DVI jack of the STB to the HDMI/DVI jack of the PC monitor. In regard to the Video Out Mode, select one of 1080i, 720p, 576p according to Video Output Resolution of your monitor. (Purchase HDMI-to-DVI adapter.) NOTE By pressing the remote, V-OUTPUT (2 buttons), you will be able to change the output ‘YPbPr’ and ‘RGB’. (YPbPr selection is usually used for Component Input, while RGB selection is usually used for PC/HD
Résumé du contenu de la page N° 19
Connection to Analog TV (Composite/S-Video) 05 < Analog TV > If you use Composite/S-VIDEO connection, you must select 576i format. Otherwise all of the OSD (On Screen Display) will not function, including MENU, MARK, etc. Connect the Video Cables Connect a composite cable between the Video output jack of the STB and the Video input jack of the analog TV. Or, connect an S-Video cable between the S-Video output jack of the STB and the S-Video input jack of the analog TV. You can connect either com
Résumé du contenu de la page N° 20
Connection to Digital Audio Amplifier 05 < Audio Amplifier > Connect the Digital Audio Output Connect audio cables from the OPTICAL or COAXIAL digital audio output jacks of the STB to the OPTICAL or COAXIAL digital audio input jacks of the digital audio decoder or the amplifier. Do not connect the coaxial and optical audio output simultaneously and be sure to connect either optical or coaxial cable to avoid any damage to digital audio decoder or amplifier that may occur. It is recommended to us
