Résumé du contenu de la page N° 1
INSTRUCTION MANUAL
2 H.P. Dust Collector
(Model 50-761)
PART NO. A03570 - 05-12-05
Copyright © 2005 Delta Machinery
To learn more about DELTA MACHINERY
visit our website at: www.deltamachinery.com.
For Parts, Service, Warranty or other Assistance,
please call 1-800-223-7278 (In Canada call 1-800-463-3582).
Résumé du contenu de la page N° 2
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 SAFETY GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 GENERAL SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 FUNCTIONAL D
Résumé du contenu de la page N° 3
SAFETY GUIDELINES - DEFINITIONS It is important for you to read and understand this manual. The information it contains relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information. Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. Indicates a potentially hazardous situ
Résumé du contenu de la page N° 4
GENERAL SAFETY RULES READ AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFORE USING THIS EQUIPMENT. Failure to follow all instructions listed below, may result in electric shock, fire, and/or serious personal injury or property damage. IMPORTANT SAFETY INSTRUCTIONS 1. FOR YOUR OWN SAFETY, READ THE INSTRUCTION Delta may cause damage to the machine or injury to the MANUAL BEFORE OPERATING THE MACHINE. user. Learning the machine’s application, limitations, and 14. USE THE PROPER EXTENSION
Résumé du contenu de la page N° 5
POWER CONNECTIONS A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3- prong grounding type plugs and matching receptacle which will accept the machine’s plug. Before connecting the machine to the power line, make sure the switch (s) is in the “OFF” position and be sure that the electric current is of the same ch
Résumé du contenu de la page N° 6
MINIMUM GAUGE EXTENSION CORD RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES EXTENSION CORDS Ampere Total Length Gauge of Rating Volts of Cord in Feet Extension Cord Use proper extension cords. Make sure 0-6 240 up to 50 18 AWG your extension cord is in good condition and is a 3-wire 0-6 240 50-100 16 AWG extension cord which has a 3-prong grounding type 0-6 240 100-200 16 AWG plug and matching receptacle which will accept the 0-6 240 200-300 14 AWG machine’s plug. When using an exte
Résumé du contenu de la page N° 7
CARTON CONTENTS 1 2 Fig. 1 1. Motor and blower assembly 2. Stand 3 5 4 7 8 6 9 Fig. 1A 3. Dust intake port 4. Cloth-covered bag retainer ring (2) 5. One micron upper filter bag (2) 6. Six mil plastic lower bag (4) 7. Legs (2) 8. Bag retainer clamp (2) 9. Bag hanging rod (2) 7
Résumé du contenu de la page N° 8
13 11 10 12 14 15 16 17 Fig. 1B 10. Caster (4) 11. Intake cap and ring (3) 12. Bracket for bag hanging rod (2) 13. Knob for attaching legs to blower/motor assembly (4) 14. 3/8” (9.5mm) Lockwasher for attaching casters to stand (4) 15. 5/16” (8mm) Flat washers for attaching legs to blower/motor assembly and for the brackets (6) 16. M4 sheet metal screw for dust intake port (4) 17. 5/16” (8mm) Hex head screw for attaching bracket for bag hanging rod (2) UNPACKING AND CLEANING Carefully unpack t
Résumé du contenu de la page N° 9
ASSEMBLY ASSEMBLY TOOLS REQUIRED * Phillips head screwdriver * 12 mm wrench ASSEMBLY TIME ESTIMATE - 30 minutes to 1 hour FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETELY ASSEMBLED AND YOU READ AND UNDERSTAND THE ENTIRE INSTRUCTION MANUAL. A THIS MACHINE IS HEAVY. USE TWO OR MORE PEOPLE WHEN LIFTING. CASTERS B 1. Turn stand (A) upside down, as shown in Fig 1C. 2. Place 3/8” lockwasher on caster stud (B) and screw caster into threaded hole on the
Résumé du contenu de la page N° 10
ALTERNATE SETUP The steps so far will assemble the unit with the motor on top and dust intake ports on bottom, as shown in Fig 4. This unit can be assembled with the intake port (B) Fig. 5 in the up position by following the steps in “LEGS TO MOTOR/BLOWER ASSEMBLY.” The exception is to place the motor/blower assembly on a flat surface with the motor (A) Fig. 6 facing up before attaching legs. Fig. 4 NOTE: BEFORE DOING THE ALTERNATE SETUP, B REMOVE 5/16” HEX HEAD SCREWS FROM HOLES (B) FIG. 6 IN M
Résumé du contenu de la page N° 11
ATTACHING DUST COLLECTION BAG DISCONNECT MACHINE FROM POWER SOURCE USING CLOTH COVERED FLEXIBLE RING: 1. Take cloth-covered bag retainer ring (A) Fig. 8 and A B place it inside opening of clear plastic dust collection bag. Fold about 6 inches of the bag down around the retainer ring. 2. Place bag in large hole (B) Fig. 8 in motor/blower assembly and fit retainer ring (A) Fig. 8 and (A) Fig. 9 into bottom groove (B) Fig. 9. It will be necessary to bend and fold the ring to fit it into place. 3. T
Résumé du contenu de la page N° 12
ATTACHING TOP FILTER BAG DISCONNECT MACHINE FROM POWER SOURCE 1. Assemble 5/16” flatwasher (23 mm diam.) onto 5/16” hex head screw. 2. Position bracket (A) to dust collector as shown in Fig. 11. 3. Insert 5/16” hex head screw through hole in bracket and thread into the hole in dust collector. Tighten securely with a 12 mm wrench. A 4. Insert rod (A) Fig. 12 into pocket on filter bag. 5. Insert rod (A) into hole in bracket (B). 6. Work open end of filter bag into top groove of dust collector dru
Résumé du contenu de la page N° 13
OPERATION FOR OPERATOR SAFETY, DO NOT OPERATE THE MACHINE WITH ANY DUST INTAKE HOLES UNCOVERED. THEROTATINGFANLOCATED INSIDETHEBLOWER HOUSINGISACCESSIBLE THROUGHTHEDUST IN-TAKEPORTANDCANBEHAZARDOUS. ALWAYSWEARPROPERAPPAREL. DONOT WEAR JEWELRY AND KEEP FINGERS AND ALL FOREIGN OBJECTS OUT OF THE DUST INTAKE PORT. FOLLOW THE SAFETY RULES IN THIS MANUAL. STARTING AND STOPPING DUST COLLECTOR 1. The on/off button (A) Fig. 14 is located on the motor housing. To turn the machine “ON”, push the “START” b
Résumé du contenu de la page N° 14
MAINTENANCE KEEP MACHINE CLEAN Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. Wear ANSI Z87.1 safety glasses while using compressed air. FAILURE TO START Should your machine fail to start, check to make sure the prongs on the cord plug are making good contact in the outlet. Also, check for blown fuses or open circui
Résumé du contenu de la page N° 15
NOTES 15
Résumé du contenu de la page N° 16
PORTER-CABLE • DELTA SERVICE CENTERS (CENTROS DE SERVICIO DE PORTER-CABLE • DELTA) Parts and Repair Service for Porter-Cable • Delta Machinery are Available at These Locations (Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable • Delta) ARIZONA GEORGIA MINNESOTA OREGON Phoenix 85013-2906 Forest Park 30297 (Atlanta) Eden Prairie 55344 Portland 97230 4501 N. 7th Ave. 5442 Frontage Road, 9709 Valley View Road 14811 North East Airport Way Phone: (602