Résumé du contenu de la page N° 1
Installation
Instructions
If you have questions, call 800.626.2000 or visit our website at: www.monogram.com
Built-In Dishwashers
ZBD6800K
ZBD6880K
ZBD6890K*
Design Guide with
Installation Instructions
*For ZBD6890 Series also refer to the
instructions provided on the template
packed with that model.
®
Monogram.
Résumé du contenu de la page N° 2
Safety Information • IMPORTANT — The dishwasher MUST BEFORE YOU BEGIN be installed to allow for future removal from the Read these instructions completely and carefully. enclosure if service is required. • IMPORTANT — Save these instructions for • If you received a damaged dishwasher, you should local inspector’s use. Observe all governing codes and immediately contact your dealer or builder. ordinances. READ CAREFULLY. • Note to Installer — Be sure to leave these instructions with the Consu
Résumé du contenu de la page N° 3
Installation Preparation PARTS SUPPLIED: Two #8 Phillips flat head wood screws, 5/8" long to secure dishwasher to underside of countertop or sides of cabinetry. (Taped to top or side of dishwasher.) 2 Wood Screws Side and top trim pieces (on some models) Trim Pieces Template with mounting hardware (not shown) (on some models) for Model ZBD6890 Only Hose Clamp Drain Hose and Hose Clamp Drain Hose MATERIALS YOU WILL NEED: Ferrule, compression nut and 90° Elbow (3/8" NPT external thread o
Résumé du contenu de la page N° 4
Installation Preparation ADVANCE PLANNING DISHWASHER MODELS • These dishwashers are designed for versatility, ZBD6880 SS, Stainless Steel adaptable to virtually any installation. ZBD6800 BB, Black ZBD6800 WW, White • All models have a full length door without the ZBD6890 Requires a 3/4" custom panel and custom handle traditional access panel. • These dishwashers may be installed beneath countertops of stone or other materials that will not accept screws. No trim kit required. PREPARE DISHWASHER
Résumé du contenu de la page N° 5
Installation Preparation Method 1—Air Gap with Waste Tee or Disposer DRAIN REQUIREMENTS An air gap must be used when required by local codes and • Follow local codes and ordinances. ordinances. The air gap must be installed according to • Do not exceed 10 feet distance to drain. manufacturers instructions. • Do not connect drain lines from other devices to the dishwasher drain hose. NOTE: This dishwasher is equipped with a high drain loop. There is no minimum height required for drain hose rout
Résumé du contenu de la page N° 6
Installation Preparation PREPARE ELECTRICAL WIRING ATTENTION Le mauvais branchement du conducteur WARNING de mise à la terre peut causer des risques FOR PERSONAL SAFETY: Remove house de choc électrique. En cas de doute sur fuse or open circuit breaker before la mise à la terre de l’appareil, consulter beginning installation. Do not use an un électricien agrée ou un technicien de extension cord or adapter plug with this réparation. appliance. ATTENTION Alternate SÉCURITÉ : Enlever le fusible d
Résumé du contenu de la page N° 7
Installation Instructions PREPARE HOT WATER LINE BEFORE YOU BEGIN Locate and set aside the two Phillips head • The line may enter from either side, rear or floor mounting screws wrapped with yellow tape within the shaded area shown in Figure F. and stuck to the top or side of the dishwasher. • The line may pass through the same hole as the electrical cable and drain hose. Or, cut an additional 1-1/2" dia. hole to accommodate the water line. If power cord with plug is used, water line must not
Résumé du contenu de la page N° 8
Installation Instructions STEP 2 REMOVE WOOD BASE, STEP 4 INSTALL POWER CORD INSTALL LEVELING LEGS Skip this step if dishwasher will be direct wired or has a factory installed power cord. IMPORTANT — Do not kick off wood base! The power cord and connections must comply with Damage will occur. the National Electrical Code, Section 422 and/or local • Move the dishwasher close to the installation location codes and ordinances. and lay it on its back. • Maximum power cord length is 4 feet beyond t
Résumé du contenu de la page N° 9
Installation Instructions STEP 6 POSITION WATER LINE STEP 8 SLIDE DISHWASHER AND HOUSING WIRING PARTIALLY INTO CABINET • Position water supply line and house wiring on the DO NOT PUSH AGAINST FRONT PANEL WITH KNEES. floor of the opening to avoid interference with base DAMAGE WILL OCCUR. of dishwasher and components under dishwasher. • Slide dishwasher into the opening a few inches at a time. 4" 5" 5" 4" 6" House Water Wiring Figure M Line Reposition Dishwasher by Grasping Both Sides With Hands
Résumé du contenu de la page N° 10
Installation Instructions STEP 10 POSITION DISHWASHER UNDER COUNTERTOP • Push the dishwasher into the cabinet. • Push at the sides with your hands. Do not use your knee against the door since door damage will occur. • Check that the tub insulation blanket does not get “bunched-up” or interfere with the springs as you slide it into the cabinet. • Center the dishwasher in the opening. Reposition Dishwasher • Check that the edges of the dishwasher door are by Grasping Both behind the cabinet frame
Résumé du contenu de la page N° 11
Installation Instructions STEP 11 LEVEL DISHWASHER • Level the Access Hole dishwasher by IMPORTANT — Dishwasher must be level adjusting the for proper dish rack operation and wash performance. four leveling legs individually. • Place level on door • If adjustment to the and rack track inside right rear leveling the tub as shown to Turn Legs leg is required, gain check that the to Adjust Figure X access by loosening dishwasher is level. junction box bracket screw (through the access hole) Check
Résumé du contenu de la page N° 12
Installation Instructions STEP 13 CONNECT WATER SUPPLY Compression Nut Ferrule Connect water supply line to 90° elbow. • Slide compression nut, then ferrule over end of water line. Hot Water • Insert water line into 90° elbow. 90° Elbow Supply Line • Slide ferrule against elbow and secure with compression nut. IMPORTANT — Check to be sure that door spring does not rub or contact the fill hose or water supply Figure BB line. Test by opening and closing the door. Re-route the 90° Elbow lines if
Résumé du contenu de la page N° 13
Installation Instructions STEP 15 CONNECT POWER SUPPLY STEP 16 PRE-TEST CHECK LIST Skip this step if equipped with power cord. Review this list after installing your dishwasher to Go to step 16. avoid charges for a service call that is not covered by your warranty. Verify that power is turned off at the source. • Remove junction box cover “A”. Check to be sure power is OFF. • Secure house wiring to the back of the junction box Open door and remove all foam and paper with a strain relief “B”
Résumé du contenu de la page N° 14
Toekick Installation Instructions STEP 17 DISHWASHER WET TEST STEP 18 REPLACE TOEKICK Turn on power supply (or plug power cord into • Place toekick against the legs of the dishwasher. outlet, if equipped). Start the unit to check for leaks. – Push RINSE ONLY pad. – Push START/RESET pad one time. – Close door. Check to be sure that water enters the dishwasher. If water does not enter the dishwasher, check to be sure that water and power are turned on. Check for leaks under the dishwasher. I
Résumé du contenu de la page N° 15
Custom Panel Dimensions CUSTOM PANEL FOR MODEL ZBD6890 This dishwasher requires a field installed 3/4" thick custom panel and custom handle. An installation template is packed with these models and may be obtained in advance. Order Pub. No. 31-30569. Complete panel installation instructions are included on the template. Custom Countertop Panel Size Cabinets Side A View Floor B 3/4" Max. Bottom of Figure II Adjacent Cabinetry STEP A—Determine custom panel height 1. Measure dimension A, from th
Résumé du contenu de la page N° 16
NOTE: While performing installations described in this book, safety glasses or goggles should be worn. ® For Monogram local service in your area, call 1.800.444.1845. NOTE: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice. ® Monogram. GE Consumer Products Pub. No. 31-30568 General Electric Company Louisville, KY 40225 Part No. 206C1559P108 12-03 JR © 2003 General Electric Company
