Résumé du contenu de la page N° 1
MPH2089 O/M.QXD 9/4/01 10:30 AM Page 21
DIGITAL ANSWERING MACHINE WITH
DATE/TIME STAMP
MODEL: MPH2089
BEFORE OPERATING THIS PRODUCT,
PLEASE READ THESE INSTRUCTIONS COMPLETELY.
OPERATING INSTRUCTIONS
Résumé du contenu de la page N° 2
MPH2089 O/M.QXD 9/4/01 10:30 AM Page 1 Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses
Résumé du contenu de la page N° 3
MPH2089 O/M.QXD 9/4/01 10:30 AM Page 2 IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on this product. 3. Do not use this product near water- for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swim
Résumé du contenu de la page N° 4
MPH2089 O/M.QXD 9/4/01 10:30 AM Page 3 IMPORTANT SAFETY INSTRUCTIONS 1. If your local telephone exchange only accepts Pulse dialing, you may have to switch the Tone/Pulse switch to Tone to access certain services that require Tone signalling (such as home banking). After the initial line is connected to the number you are calling, switch the Tone/Pulse switch to Tone to access Tone signalling. When you have completed your call, please switch the Tone/Pulse switch back to Pulse. 2. Hearing aid
Résumé du contenu de la page N° 5
MPH2089 O/M.QXD 9/4/01 10:30 AM Page 4 LOCATION OF CONTROLS 1 2 3 4 5 6 7 8 9 10 11 1213 1. DELETE Button 2. SKIP ➛➛/MEMO Button 3. PLAY/PAUSE Button 4. Display 5. Battery Compartment (Bottom of Unit) 6. DATA Jack (Rear of Unit) 7. LINE Jack (Rear of Unit) 8. SKIP ❿❿/OGM Button 9. TIME Button + 10. DC Jack (Rear of Unit) - 11. NEW MESSAGE Indicator 12. ON/OFF Button 13. VOLUME Control (Side of Unit) 4
Résumé du contenu de la page N° 6
MPH2089 O/M.QXD 9/4/01 10:30 AM Page 5 INSTALLATION This section has been designed to provide a reference guide to help set up the unit. DC 9V POWER TELEPHONE AC POWER JACK LINE JACK A T DA JACK OR ADAPT O T EXTERNAL TELEPHONE TELEPHONE LINE CORD 1. Unpack and make sure all the items have been included: Base Unit, Power Adaptor and Telephone Line Cord. 2. Connect one end of the provided telephone line cord into the LINE jack on the rear of the unit and the other end into a modular telephone j
Résumé du contenu de la page N° 7
MPH2089 O/M.QXD 9/4/01 10:30 AM Page 6 POWER SOURCES AC Power Adapter To operate the unit using AC power, connect the AC adapter to the DC jack on the rear of the unit and to a wall outlet having 120V, 60Hz only. CAUTION: Use only the AC adapter provided with the unit. Using another AC adapter may damage the unit. When not using AC power, disconnect the AC adapter from the wall outlet by pulling the plug AC Outlet (not the cord). Do not touch the AC adapter with wet hands. AC Adapter's Plu
Résumé du contenu de la page N° 8
MPH2089 O/M.QXD 9/4/01 10:30 AM Page 7 OPERATION SETTING THE DATE/TIME 1 2 1 1 2 2 3 3 Press and hold the TIME button ❶ for Press the TIME button ❶ again and 2 seconds and the unit will announce the unit will announce the hour of the the day of the week (i.e. Monday). time (i.e. 12 AM). Press the Press the SKIP ➛➛/MEMO button ❷ SKIP ➛➛/MEMO button ❷ to decrease to decrease or the SKIP ❿❿/OGM or the SKIP ❿❿/OGM button ❸ to button button ❸ to increase until the increase until the present hour i
Résumé du contenu de la page N° 9
MPH2089 O/M.QXD 9/4/01 10:30 AM Page 8 OPERATION (CONTINUED) RECORDING OGM (OUTGOING MESSAGE ) Recording an OGM allows the caller to hear the OGM and then be able to leave a message. Please note that there is an automatic message on this unit, recording a new OGM will disable this default message. 1 2 1 2 Press and hold the SKIP ❿❿/OGM When finished recording, press the button for approximately 2 seconds PLAY/STOP button ❶. The newly until a short beep is heard, and then recorded outgoing mes
Résumé du contenu de la page N° 10
MPH2089 O/M.QXD 9/4/01 10:30 AM Page 9 OPERATION (CONTINUED) SETTING THE UNIT TO ON MODE (Incoming Messages will be recorded) When the answering machine is turned on, when a call is received the unit will play the OGM and then record a message. 1 Make sure the OGM is recorded. Press the ON/OFF button; the NEW MESSAGE indicator will light solid and the unit will announce, “Answer On” NOTES: If the unit detects a dial tone, silence or a busy signal, the unit will hang up and may not regist
Résumé du contenu de la page N° 11
MPH2089 O/M.QXD 9/4/01 10:30 AM Page 10 OPERATION (CONTINUED) RECORDING/PLAYING A PERSONAL MEMO 1 2 2 1 To record a personal memo which will After the message is recorded, press be played the next time somebody the PLAY/STOP button ❶ to stop the retrieves the memos, press and hold recording. “oo” will appear in the the SKIP ➛➛/MEMO button for display when memo’s have been approximately 2 seconds; a beep will recorded. To hear the memo(s), press sound. When the beep is heard, the SKIP ➛➛/MEMO
Résumé du contenu de la page N° 12
MPH2089 O/M.QXD 9/4/01 10:30 AM Page 11 OPERATION (CONTINUED) PLAYING BACK INCOMING MESSAGES (ICMs) The NEW MESSAGE indicator will blink when the unit has recorded new messages and the display will show the total amount of messages. To hear messages, proceed as follows: 1 2 Make sure the SPEAKER VOLUME Press the PLAY/STOP button to hear control is adjusted as desired. only the new ICM/MEMO messages. As the messages are played back, the unit will say the time they were received before play
Résumé du contenu de la page N° 13
MPH2089 O/M.QXD 9/4/01 10:30 AM Page 12 OPERATION (CONTINUED) CHANGING THE REMOTE CODE 5 To change the remote code, please follow the instructions given on page 17. NOTES: If a power failure occurs and there is a dead or no battery, the Remote To stop playback, press the Code resets to 000. PLAY/STOP button and the unit will If you forget the Remote Code, save the previous messages. unplug the AC adaptor and disconnect the battery and it will reset to 000. Be sure to write down your ne
Résumé du contenu de la page N° 14
MPH2089 O/M.QXD 9/4/01 10:30 AM Page 13 REMOTE OPERATION TURNING THE ANSWERING MACHINE OFF 1 2 Call the answering machine from a Press the “*” pad, then the “5” pad to separate line. After the OGM is played turn the unit off. (press “*” to skip OGM), and the beep is heard, enter your remote code within 10 seconds. REMOTELY PLAYING THE OGM (OUTGOING MESSAGE) 1 2 Call the answering machine from a Press the “1” pad and the OGM will separate line. After the OGM is played play. (press “*” to skip
Résumé du contenu de la page N° 15
MPH2089 O/M.QXD 9/4/01 10:30 AM Page 14 REMOTE OPERATION REMOTELY PLAYING INCOMING MESSAGES (ICM’S) 1 2 Call the answering machine from a Press the “4” pad to play all messages separate line. After the OGM is played or the “5” pad to play only new (press “*” to skip OGM), and the beep messages. is heard, enter your remote code within 10 seconds. TO ENTER THE PLAYBACK MENU 1 2 Call the answering machine from a Press the “9” pad to access the Play separate line. After the OGM is played menu as
Résumé du contenu de la page N° 16
MPH2089 O/M.QXD 9/4/01 10:30 AM Page 15 REMOTE OPERATION (CONTINUED) TO DELETE A MESSAGE TO STOP PLAYBACK 1 1 WHILE IN THE PLAY MENU: WHILE IN THE PLAY MENU: To stop playback, press the “7” pad. To delete a message, press the “6” pad. TO PAUSE PLAYBACK. RECORDING A MEMO 1 1 After the OGM is played, and the beep WHILE IN THE PLAY MENU: is heard, enter your remote code within To pause playback, press the “4” pad. 10 seconds. Press the “*” pad, followed To release pause, press the “4” pad by the
Résumé du contenu de la page N° 17
MPH2089 O/M.QXD 9/4/01 10:30 AM Page 16 REMOTE OPERATION (CONTINUED) ERASING ALL MESSAGES 1 After the OGM is played, and the beep is heard, enter your remote code within 10 seconds. Press the “*” pad, followed by the “4” pad to erase all ICMs and memos. REMOTE ROOM MONITORING This feature will allow you to call in and monitor the room in which the answering machine is located. 1 2 After the OGM is played, and the beep Press the “2” pad and the unit will is heard, enter your remote code monit
Résumé du contenu de la page N° 18
MPH2089 O/M.QXD 9/4/01 10:30 AM Page 17 REMOTE OPERATION (CONTINUED) TO CHANGE THE REMOTE CODE (REMOTELY) 1 2 After the OGM is played, and the beep Press the “*” pad, followed by the “3” is heard, enter your remote code pad to change the remote code. within 10 seconds. STOP CALL: Press the “#” pad to stop the remote function. TO CHANGE THE REMOTE CODE (FROM THE UNIT) 1 2 1 2 3 Press and hold the ON/OFF button for Press the SKIP ➛➛/MEMO button ❶ 2 seconds; the display will show “se” and/or SK
Résumé du contenu de la page N° 19
MPH2089 O/M.QXD 9/4/01 10:30 AM Page 18 CONVENIENT REMOTE ACCESS CARD For your convenience, cut out this card and keep it in your wallet as a reference guide when remotely calling your answering machine. IDLE MODE (No Messages Playing) Button Function 1 Play OGM 2 Starts room monitoring 3 Playback memos 4 Playback all ICMs 5 Playback new ICMs 7 Stop or save all messages 9 Enter the Playback menu. *,1 Record OGM *,2 Record a memo *,3 Change the Remote Code *,4 Erase all ICMs, memos *,5 Set ans
Résumé du contenu de la page N° 20
MPH2089 O/M.QXD 9/4/01 10:30 AM Page 19 TROUBLESHOOTING GUIDE Before requesting service, please refer to the following chart and check for the symptom you are experiencing. SYMPTOM POSSIBLE CAUSE POSSIBLE SOLUTION No Power. AC adaptor not con- Connect AC adaptor to nected to unit. DC 9V jack on unit. AC adaptor not con- Connect AC adaptor to nected to the AC outlet. the AC outlet. No power. Move to another outlet. No OGM. No OGM recorded. Record an OGM. Volume is too low. Increase volume. Mes
