Résumé du contenu de la page N° 1
INSTALLATION INSTRUCTIONS
TM
DishDrawer dishwasher
DD60D 7 models
NZ AU GB IE
590200C 12.11
Résumé du contenu de la page N° 2
2 1 FOLLOW THE INSTALLATION SEQUENCE RELEVANT TO YOUR MODEL ONLY AVAILABLE IN NZ AU ONLY AVAILABLE IN GB IE Classic Designer Integrated with remote control Integrated with badge controls DD60DC(H)X7 DD60DC(H)W7 DD60DDF(H)X7 DD60DI7 DD60DHI7 DD60DC(H)B7 DD60DDFM7 DD60DCM7 PARTS SUPPLIED PARTS SUPPLIED PARTS SUPPLIED PARTS SUPPLIED PRODUCT & CABINETRY PRODUCT & CABINETRY PRODUCT & CABINETRY PRODUCT & CABINETRY DIMENSIONS DIMENSIONS DIMENSIONS DIMENSIONS CAVITY PREPARATION CAVITY PREPARATION CUST
Résumé du contenu de la page N° 3
3 2a SAFETY AND WARNINGS - ALL MODELS IMPORTANT SAFETY INSTRUCTIONS! WARNING! Installation of this dishwasher requires basic mechanical and electrical skills. Electrical shock hazard Be sure to leave these Instructions with the Customer. Before installing the dishwasher, remove the house fuse or open the circuit Installation must comply with your local building and electricity regulations. breaker. At the completion of the dishwasher installation, the Installer must perform the
Résumé du contenu de la page N° 4
4 3a PARTS SUPPLIED - ALL MODELS Drain hose Drain hose Wire clip (2) Clamp (1) Side mounting Top support (1) joiner (1) bracket kit mounting (for securing (for securing (A and B) (2) brackets (2) Drain hose joiner) Drain hose joiner) OPTIONAL OPTIONAL Phillips Rubber Moisture protection Hexagonal Prefinished toekick (1) 16 mm washer for tape (1) socket for feet screws (9) inlet hose (1) (to prevent moisture adjustment (2) (comes already damage) (long & short) fitted) If the Drain hoses suppli
Résumé du contenu de la page N° 5
5 3b ADDITIONAL PARTS SUPPLIED WITH INTEGRATED MODELS Integrated rectangular Panel bracket (2) Panel mounting Toekick mounting bracket (1) Toekick badge (2) (attached to product) screws (12) mounting (Satin chrome supplied) (A custom toekick panel of any screws (5) material with thickness supplied with Integrated 9 - 19 mm can be screwed to the plastic toekick mounting bracket) models with badge (GB IE) only
Résumé du contenu de la page N° 6
Integrated Badge controls Integrated Remote control Designer Classic 6 4 PRODUCT DIMENSIONS O I K Plan D C F A N Side G O L B E M H J Product dimensions (mm) 1 2 2 2 2 overall height of product 820-880 820-880 820-880 820-880 A B overall width of product 599 599 599 599 3 3 C overall depth of product (excl. handle) 582 571 571 571 D depth of chassis (to back of front panel) 553 553 553 553 3 3 E maximum extension of drawer (excl. handle) 556 545 545 545 depth of front panel (excl. handle) 29
Résumé du contenu de la page N° 7
Integrated Badge controls Integrated Remote control Designer Classic 7 5 CABINETRY DIMENSIONS Q Plan R S Side P T Cabinetry dimensions (mm) Minimum clearances from adjacent cabinetry min. 13 mm clearance min. 2 mm from a corner clearance cupboard to adjacent inside height of cavity* min. 820 min. 820 min. 820 min. 820 P cupboard door Q inside width of cavity 600 600 600 600 R inside depth of cavity min. 560 min. 560 min. 560 min. 560 recommended height of adjacent cabinet space 720 720 min
Résumé du contenu de la page N° 8
8 6 INTEGRATED MODELS ONLY - CUSTOM PANEL CALCULATIONS The following calculations assume the top of the upper panel is FRONT PANEL SPECIFICATIONS aligned with the top of the adjacent cabinetry. The fi nal 16 -20 mm panel thickness panel/cabinetry alignment is achieved by adjusting the feet: min. 2 mm O Adequately sealed to withstand moisture (50 C @ 80% RH) Maximum weight of panel: 9 kg WIDTH OF ALL PANELS TOEKICK PANEL SPECIFICATIONS Measure A (the width between adjacent door/drawer f
Résumé du contenu de la page N° 9
9 7 CAVITY PREPARATION Important! BENCHTOP The power outlet must be located in a cabinet adjacent to the dishwasher cavity. Moisture 220-240 VAC min. 9.5 A 10 mm protection tape must be applied. Water Connection Recommended COLD (Maximum 60°C). ¾ “ BSP (GB20) to suit flat washer. These marks indicate Water Pressure formed bracket screw locations, if securing Water softener models by drawer removal. Max. 1 MPa (145 psi) Min. 0.1 MPa (14.5 psi) Models without water softener Max. 1
Résumé du contenu de la page N° 10
10 8 MAXIMUM DISTANCE OF HOSES & CORD FROM CHASSIS EDGE Left hand side Right hand side Drain hoses - 2000 mm Drain hoses - 1800 mm Inlet hose - 1250 mm Inlet hose - 1650 mm Power cord (excl. plug) - 1650 mm Power cord (excl. plug) - 1650 mm
Résumé du contenu de la page N° 11
11 NOW CHOOSE WHICH INSTALLATION METHOD (a) or (b) IS MORE SUITABLE FOR YOUR CABINETRY... RECOMMENDED METHOD (a) - SECURE WITHOUT DRAWER REMOVAL (FRAMELESS CABINETRY ONLY) 10a 9a PULL THROUGH HOSES & PUSH INTO THE CAVITY ATTACH SIDE MOUNTING BRACKETS optionally attach the Clip all four side mounting brackets into two top mounting brackets (x2) their slots using a flat-bladed screwdriver. B Ensure they’re securely fitted before A sliding product into cavity. Ensure the product is level B A A
Résumé du contenu de la page N° 12
12 11a 12a SECURE TO THE CABINETRY ON THE SIDES OPTIONALLY SECURE TO THE CABINETRY ABOVE The top mounting 1 brackets will only (x2) Open the bend upwards a drawer halfway. maximum of 10 mm. Using a flat-bladed screwdriver, prise the grey Replace the grey rubber plug out rubber plug back into of the trim moulding. the trim moulding and ensure the trim seal is facing forward. 2 3 Using a small Philips screwdriver, screw through the trim moulding, securing the side mounting bracket t
Résumé du contenu de la page N° 13
13 ALTERNATIVE METHOD (b) - SECURE BY DRAWER REMOVAL 9b PULL THROUGH HOSES & PUSH INTO THE CAVITY 10b REMOVE THE LOWER DRAWER To prevent kinked hoses, we recommend rotating the drawer anti-clockwise and resting it on its side after removal. optionally attach the 4 3 two top mounting brackets (x2) You can initially level the product 1 4 5 2 As you push product in, pull You can raise or lower the through hoses and cord, product by twisting the feet. Then take care when ensuring they don’t g
Résumé du contenu de la page N° 14
14 11b SECURE TO THE CABINETRY ON THE SIDES 12b OPTIONALLY SECURE TO THE CABINETRY ABOVE To access the side brackets, The top mounting you might have to push aside brackets will only the insulation. After securing, (x2) bend upwards a ensure the sound insulation is maximum of 10 mm. repositioned correctly. For further adjustment, using the most appropriate length Hexagonal socket supplied, fully extend levelling feet up to required distance by hand. Secure using two pairs of formed
Résumé du contenu de la page N° 15
15 14b FIT THE SUPPLIED TOEKICK PANEL (OPTIONAL FOR INTEGRATED MODELS) Where the toekick meets the bottom 1 3 5 7 of the tub is the Mounting rail cut-off point 19 9 Lay the toekick face down on Turn the toekick over and Smooth the edge with a file. a chopping board or similiar score along the same line Be careful of sharp edges. 4 6 8 Slide the toekick onto the mounting rails either side and screw 2 the toekick onto the bottom of tub on either side. 19 Important! Do not overtighten scr
Résumé du contenu de la page N° 16
16 INTEGRATED MODELS WITH REMOTE (NZ AU) ONLY - INSTALLING THE FRONT PANELS 15a 16a ATTACH PANELS TO PANEL BRACKETS REMOVE BRACKETS FROM PRODUCT WARNING! 2 Electrical Shock Hazard 16 mm x6 There must be at least 1 3 screws used each side Before continuing, ensure that the product is disconnected from the power supply. Failure to follow this warning may result in electrical shock, injury or fire. Important! Break off and discard the tab at the top of the Lower Panel Bracket. 1 2 3 1 Align bot
Résumé du contenu de la page N° 17
17 INTEGRATED MODELS WITH REMOTE (NZ AU) ONLY - INSTALLING THE FRONT PANELS 19a 20a ADJUST PANEL HEIGHT TO ALIGN THE CABINETRY GAPS FITTING A CUSTOM TOEKICK PANEL 16 mm x5 + or - 2 mm With the front panels fitted, insert an appropriately sized Philips screwdriver into the hole above the door You can optionally glue your pin and rotate the panels up or down to align the gaps custom toekick panel onto the in your cabinetry. supplied panel Repeat on the other side if necessary. Each panel ha
Résumé du contenu de la page N° 18
Badge zone Badge z dge zo on ne e 228.5 mm 228.5 mm 18 INTEGRATED MODELS WITH BADGE (GB IE) ONLY - INSTALLING THE FRONT PANELS & BADGE CONTROLS 15b 16b DETERMINE BADGE CUTOUT LOCATIONS REMOVE BRACKETS & DISCONNECT BADGES WARNING! Electrical Shock Hazard Before continuing, ensure that the product is 3 disconnected from the power supply. Failure to follow this warning may result in electrical shock, injury or fire. 1 2 1 Repeat for the other drawer 4 17b 18b ROUTE BADGE WIRING THROUGH PANEL ATTAC
Résumé du contenu de la page N° 19
19 INTEGRATED MODELS WITH BADGE (GB IE) ONLY - INSTALLING THE FRONT PANELS & BADGE CONTROLS 19b 20b REATTACH BADGES & EARTH THE PANELS ATTACH PANELS TO PRODUCT Important! WARNING! Ensure the rubber seal Electrical Shock Hazard between the drawer Connect the integrated badge earth wire to one of the two tabs and panels is kept in provided on the panel bracket. place. 2 To earth the panel bracket, connect the earth wire from the product to the other tab. Any custom metal component (e.g.
Résumé du contenu de la page N° 20
20 23 THERE ARE TWO DIFFERENT PLUMBING AND DRAINAGE OPTIONS. CHOOSE WHICH IS MORE SUITABLE. Dishwasher using sink trap with drain hose joiner Dishwasher and Standpipe Ø 38 mm Supplied drain hose joiner If space is limited 19 mm for fixing, push If space is limited waste tee hose through drain for fixing, push hose support hose through drain to required height hose support to required height max. 3 120 mm 2 38 mm 2 1 HIGHLOOP min. 150 mm 1 see 24 * see 24 * min. R 200 mm min. R 2
