Résumé du contenu de la page N° 1
INS INSTALLATION TALLATION
R
INST INSTRUCTIONS RUCTIONS
GEM-RP3DGT L
Digital Keypad
This Guide includes programming instructions for the
following control panels: • GEM-P816
• GEM-P1632
• GEM-P3200
• GEM-P9600
Quick Start:
GEMINI
1. Referring to the control panel wiring diagram, connect siren, aux. power, pgm.
SYSTEM ARMED
output, remote bus, earth ground, zone and telephone wiring. 01/01/97 12:00AM
ENT A1
17
NOTE: See Installation Instructions for the appropriate control panel.
NEXT/YES
Résumé du contenu de la page N° 2
2
Résumé du contenu de la page N° 3
INTRODUCTION The GEM-RP3DGTL is a dual 7-segment digital keypad that is compat ible with the NAPCO GEM-Series GEM-P816, P1632, P3200 & P9600 control-panels. Refer to User Guide OI249 for operation instructions. While the GEM-RP3DGTL may be used to fully program the control, the GEM-RP1CAe2 keypad provides the optimum in ease of keypad programming. SPECIFICATIONS Dimensions: 4 3/8” x 5 7/8” x 11/16” MOUNTING THE KEYPAD off the two hooks at the top. The GEM-RP3DGTL features a handy pull-up referen
Résumé du contenu de la page N° 4
EASY PROGRAM MODE OVERVIEW ENTERING THE EASY KEYPAD PROGRAM MODE 1 programmed and press A 2 Press NO ( F 17 NOTE: 17 B 3 E Use the following guide to answer the Easy Program Mode questions which will quickly allow you to create a custom default program. Press A to set cursor, NEXT ( E ) to go forwards, PRIOR ( F) to go backwards, J to save C ANSWERING A QUESTION IN THE EASY PROGRAM MODE Pressing A J If no additional programming is necessary for the question, press NEXT ( E REVIEWING THE DATA
Résumé du contenu de la page N° 5
Programming the GEM-P816 & GEM-P1632 Total Number of Zones in Area 1 (Appears for New Panel Only) Press the A button and then directly enter the total number of zones to be 01 number of zones, including leading zeros. Use number buttons 1 9 . NOTE: Press the 0 button for a zero. The system is based on to the next group of 4. For example, if you enter 18, it will automatically convert this to 20 zones. Press J to save. Press NEXT ( E ) button to proceed. NOTE: If you are programming a 2 Area s
Résumé du contenu de la page N° 6
Programming the GEM-P816 & GEM-P1632 Entry/Exit Zones in Area 1 (Appears for New Panel Only) Press the A 07 Di- Use number buttons 0 through 9. Press Jto save and then repeat for any additional zone(s). Press NEXT ( E ) button to proceed. NOTE: Chime will automatically be programmed for all E/E zones. Interior Zones in Area 1 (Appears for New Panel Only) Press the A 08 Di- 0 9 . Press J zone(s). Press NEXT ( E NOTE: Number of Keypads in Area 1 Press the A button and then directly enter the to
Résumé du contenu de la page N° 7
Programming the GEM-P816 & GEM-P1632 Central Station Receiver 1 Format From the table below, enter the central station's receiver format. Use number 1 9 NOTE: Press G0 0 13 for a blank space (•). Press G 1 through G 4 for letters B–E, J to save. Press NEXT ( E NOTE: Central Station Receiver 2 and 3 Formats can only be entered in Direct Address Programming. See CS Receiver Options. DATA CS RECEIVER 1 FORMAT DATA CS RECEIVER 1 FORMAT ENTRY ENTRY •(blank) Ademco Slow, Silent Knight Slow 5 Univers
Résumé du contenu de la page N° 8
Programming the GEM-P816 & GEM-P1632 RF Transmitter Programming (For wireless systems only. Also see Quick Method, which follows) Press the A button and for each transmitter (key fob transmitters also), 15 1 2 3 The 1-digit checksum number (C) printed on the transmitter and box. 4 The Point number (1–4) (P); enter “9” for unsupervised Press J to save. Then go to step 1 to enter next transmitter. When all transmitters are entered, press NEXT ( E NOTE: When programming the RF ID number: G 0 G 1
Résumé du contenu de la page N° 9
Programming the GEM-P816 & GEM-P1632 Key Fob Transmitters Keyfobs can be programmed as “Arm/Disarm” devices using the ON and OFF 16 Press the A 1 The Key Fob Transmitter number (01–15). 2 The area number to which transmitter is assigned (1 or 2); enter 0 to disable 3 The 6-digit RF ID # printed on the transmitter (enter all numbers and/or DATA AUX 1/AUX 2 4 The 1-digit checksum number printed on transmitter. ENTRY OPTIONS 5 •(blank) None 9 Keypad Panic 6 0 Aux K.P. Panic B Instant C Toggle Aux
Résumé du contenu de la page N° 10
Programming the GEM-P3200 & GEM-P9600 Total Number of Zones and Keypads in Area 1. Total Number of Zones and Keypads in Area 2. 01 (Appears for New Panel Only) 2 2 2 J Press 3 to Press 3 to Press 3 to Press 3 to select # of select # of select # of select # of K/Ps in Area 1 K/Ps in Area 2 1 Press the A 3 to select the total number of zones to be programmed for Area 1. Valid entries are from 08 to 24 in multiples of 4. 2 Press 2 and press 3 to select the total number of keypads to be programme
Résumé du contenu de la page N° 11
Programming the GEM-P3200 & GEM-P9600 Central Station Receiver 1 Format From the table below, enter the central station's receiver format. Use number 05 1 9 NOTE: Press G0 0 for a blank space (•). Press G 1 through G 4 for letters B–E, J to save. Press NEXT ( E NOTE: Address Programming. See CS Receiver Options. DATA CS RECEIVER 1 FORMAT DATA CS RECEIVER 1 FORMAT DATA CS RECEIVER 1 FORMAT ENTRY ENTRY ENTRY •(blank) Ademco Slow, Silent Knight Slow 4 Radionics, DCI, Franklin Slow 0 Radionics Mo
Résumé du contenu de la page N° 12
Programming the GEM-P3200 & GEM-P9600 RF Transmitter Programming (For wireless systems only. Also see Quick Method, which follows) Press the A 07 1 2 3 The 1-digit checksum number (C) printed on the transmitter and box. 4 The Point number (1–4) (P); enter “9” for unsupervised Press J to save. Then go to step 1 to enter next transmitter. When all transmitters are entered, press NEXT ( E NOTE: G 0 G 1 ; G 2 G 3 ; G 4 ; “F” = G 5 . Quick Method. If a receiver is already installed in the panel, Na
Résumé du contenu de la page N° 13
Programming the GEM-P3200 & GEM-P9600 Key Fob Transmitters Keyfobs can be programmed as “Arm/Disarm” devices using the ON and OFF 08 Press the A 1 The Key Fob Transmitter number (01–15). 2 The area number to which transmitter is assigned (1-8); enter 0 to disable 3 The 6-digit RF ID # printed on the transmitter (enter all numbers and/or DATA AUX 1/AUX 2 4 The 1-digit checksum number printed on transmitter. ENTRY OPTIONS 5 •(blank) None 9 Keypad Panic 6 0 Aux K.P. Panic B Instant C Toggle Aux
Résumé du contenu de la page N° 14
DIRECT ADDRESS PROGRAM MODE This is an extension of the Dealer Program Mode. This method of programming is used in conjunction with the Keypad Programming Worksheets contained in the control panel programming guide. Refer to these worksheets to identify the KEYPAD PROGRAMMING OVERVIEW Direct Address Programming allows you to go directly to the address DATA ENTRY ADDRESS LOCATIONS options. Whereas the Easy Menu Program Mode is a simple quick LOCATIONS LEFT DIGIT RIGHT DIGIT start guide with limit
Résumé du contenu de la page N° 15
15
Résumé du contenu de la page N° 16
NAPCO SECURITY SYSTEMS, INC. (NAPCO) thorizes any other person purporting to act on its behalf rants its products to be free from manufacturing defects to modify, to change, or to assume for it, any other in materials and workmanship for thirty-six months fol- lowing the date of manufacture. NAPCO will, within said period, at its option, repair or replace any product failing In no event shall NAPCO be liable for an amount in to operate correctly without charge to the original pur- excess of NAPC
