Instruction d'utilisation Trango Broadband PTZ-900

Résumé du contenu de la page N° 1

™
PTZ-900
900MHz Spread-Spectrum Digital
Wireless Pan/Tilt/Zoom Camera Control
Transmission System
Installation and
Operating Instructions
THE LEADER IN WIRELESS VIDEO

Résumé du contenu de la page N° 2

Quick-Start Guide 1 Prior to installing the wireless link, verify proper operation of PTZ controller (keyboard) and hard-wired receiver/driver or dome. 2 Determine the bit rate and interface (RS232 or RS485/422) of the hard-wired system. If it is not 9600 bps and RS485/422, you will need either to change the setting of the PTZ controller and receiver/driver or to change the settings of the PTZ-900 equipment. See the end of this manual for information on changing PTZ-900 internal settings using T

Résumé du contenu de la page N° 3

10 To help protect against potential lightning damage use a lightning Important! Intentional or unintentional changes or modifications not surge arrester in line with all cabling entering a structure. expressly approved by the party responsible for compliance must not be made. Any such modifications could void the user's authority to Important! Power Adapter must be kept dry. operate the equipment. Your Trango PTZ-900 System Congratulations on choosing Trango Systems, Inc., to fulfill your wi

Résumé du contenu de la page N° 4

Installation Important! The PTZ-900 enclosures are designed for a steel pole with 3 a maximum diameter of 2 / ″ and a wall thickness of ¼″. The pole must 8 Make sure that you have tested the PTZ controller and receiver/driver/ be securely mounted into the ground or to a structure to prevent move- dome using a direct connection (with wires) before installing the wire- ment of the antenna and camera in windy conditions. This pole also less link. Also, it is recommended that the wireless link be te

Résumé du contenu de la page N° 5

  
    
   
 
    !  
"#$ %&$ '()

 

   * +   !   ! "   ! "
    
     

    
# 
# 

  
  

  Transmitter Operation    Antenna jack. This connector is used to connect an appropriate Trango 

Résumé du contenu de la page N° 6

Power input. Accepts a power source between 6 and 13 volts DC. It is Receiver Operation highly recommended that the supplied power adapters (7VDC) be used to reduce the heat dissipated from the unit. If another power adapter Antenna jack. This connector is used to connect an appropriate Trango is to be used, ensure that it is well regulated (±5%). Batteries may be receiver antenna. The antenna authorized for use with this unit is the used as external power sources as well. The nominal current dr

Résumé du contenu de la page N° 7

munication is established. If a connection is not made within twenty give the best results in general. seconds, the unit will exit programming mode and enter normal oper- ating mode. In this event, simply reboot power to the unit and try again. Raise transmitter and receiver antennas above ground and away from obstacles and traffic, including foot traffic. After entering the program, a screen is displayed showing the current settings. The user may change the settings and then must click SAVE Ver

Résumé du contenu de la page N° 8

Data not received. Parametric Specifications Verify that a clear line of sight exists between the transmitter and receiver antennas for distances greater than five hundred feet. PTZ-900TX Transmitter: Electrical Radio Section Spurious Attentuation: > 50 dBc Check that the transmit and receive PN sequences, data rate, mode, Frequencies: Symbol Rate: 64.516 kbps 64 hopping frequencies, including the Hopping Rate: 600 hops/sec and address are set the same. waiting channel, spaced by 400kHz Error Co

Résumé du contenu de la page N° 9

Parametric Specifications PTZ-900RX Receiver: Electrical Radio Section Data Output Section Frequencies: 902.2MHz to 927.8MHz Buffer Size: 48 bytes Cascade Noise Figure: < 6dB Data Output Level: software-selectable –6 Sensitivity for 10 BER: –95dBm max. rates between RS232 and RS485/422 Adj. Channel Rej: > 50dB (RS485/422 factory default) Image Rejection: > 60dB Data Rate (User): 1200, 2400, 4800, Frequency Plan: 9600, or 19200 bps user-configurable double-conversion 1st IF at 110.6MHz, via Trang