Résumé du contenu de la page N° 1
1080I Multi-purpose
Digital Camera
AK-HC910L
Before attempting to connect, operate or adjust this product,
please read these instructions completely.
Printed in Japan
D
F0905Y1105 VQTB0099
Résumé du contenu de la page N° 2
For Your Safety DO NOT REMOVE PANEL COVERS BY UNSCREWING. $ To reduce the risk of electric shock, do not remove the covers. No user serviceable parts inside. Refer servicing to qualified service personnel. WARNING: • TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. • TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, KEEP THIS EQUIPMENT AWAY FROM ALL LIQUIDS. USE AND STORE ONLY IN LOCATIONS WHICH ARE NOT EXPOSED TO THE RISK OF DRIPPING OR SPLASHING LIQUIDS,
Résumé du contenu de la page N° 3
For Your Safety Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households) This symbol on the products and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling, please take these products to designated collection points, where they will be accepted on a free of charge basis. Alternatively, in some countries you may be able to return your pr
Résumé du contenu de la page N° 4
Contents For Your Safety...............................2, 3 Setting of Menu Items..............17 to 29 Preface ...............................................5 _ Configuration of menu display screen .........................................17 Features..............................................5 _ USER menu (Initial screen) ........18 Precautions.........................................6 ! Maintenance menu ............19 to 25 Major Operating Controls and 1 Black shading correction Their F
Résumé du contenu de la page N° 5
Thank you very much for purchasing the multi-purpose digital camera. Preface This camera employs new 2/3q 2.2 million-pixel FIT CCD [1920(H)k1080(V)], realizing a compact light-weight system including the optical system. Also, the newly developed CCD having an FIT configuration suited for higher picture quality and the development of low-noise, high-speed amplifiers have enabled the realization of high sensitivity, high S/N ratio, and wide dynamic range. With the newly developed digital signal p
Résumé du contenu de la page N° 6
Precautions DON’TS DO’S • Do not attempt to disassemble the • Refer any servicing to qualified service camera or other units. In order to prevent personnel. electric shock, do not remove screws or • Handle the camera with care. covers. There are no user-serviceable • Protect the precision made lens by parts inside. placing the lens cap over when the • Do not abuse the camera. Avoid striking, camera is not in use. If the lens is not shaking, etc. The camera contains installed, protect the surface
Résumé du contenu de la page N° 7
Major Operating Controls and Their Functions _ Front Panel 1 Lens Mount 2/3q standard bayonet type (B4 mount) lens is installed. 2 Lens Fixing Ring Knob Lens is fixed by turning the knob counterclockwise. 3 Cable Clamp Used to clamp the lens cable. 4 Lens Connector [LENS] Used to connect the camera cables of the lens. Pin No. Signal Pin No. Signal 1 Return control 7 Iris follow 2 VTR-S/S 8 Iris auto selection 3 UNREG GND 9 —— 4 Iris manual selection 10 —— 5 Iris control 11 —— 6 UNREG 12V 12 NC _
Résumé du contenu de la page N° 8
Major Operating Controls and Their Functions 6 Camera mounting hole (1/4-20UNC) 7 Camera mounting hole (3/8-16UNC) The screw holes can be used to secure the camera for installing it on camera housing, and when using a pan/tilt head or a tripod. _ Side Panel 8 Breaker [BREAKER] If the breaker is operated due to over-current or the like, check the cause and eliminate the trouble, then press the breaker button. 9 Zoom/Focus Connector [ZOOM/FOCUS] Used to connect the zoom/focus control cables of len
Résumé du contenu de la page N° 9
Be sure to ask the dealer for the installation, How to Install adjustment and connection of this equipment. _ How to set the lens • Standard 2/3q bayonet type (B4 mount) lens of any makers can be used*. 1 Turn the lens fixing ring knob counterclockwise to remove the lens mount cap. 2 Set the lens in place, and turn the lens fixing ring knob clockwise to precisely fix the lens. 3 Connect the lens cable to the lens connector. 4 Connect the remote (zoom/focus control) cable to the zoom/focus connec
Résumé du contenu de la page N° 10
How to Set Up the System (Connection) _ Connection of remote control box • Use multi-cable for the connection of Camera Controller AK-HRP900L and this unit. Coaxial Cable HD-SDI (5C-FB) D-sub 15-pin HD Monitor Multi-purpose Video Digital Camera Input AK-HC910L Multi-cable (5m) Signal AK-HDMLTCA05 HD Monitor YPbPr AC adapter External AW-PS505A sync NOTE signal Note that the monitor output is (3 value attenuated and deteriorated if sync) the cable is too long. DC Power Cable D-sub 15-pin Ca
Résumé du contenu de la page N° 11
Multi-purpose Digital Camera Control System Configuration Remote (zoom/focus control) cable HD-SDI Coaxial Cable (5C-FB) D-sub 15-pin Remote Multi-purpose controllable Digital Camera lens AK-HC910L Multi-cable (5m) AK-HDMLTCA05 HD Monitor AC adapter AW-PS505A External sync signal (3 value sync) DC D-sub 15-pin Power Cable Camera Controller AK-HRP900L - 11 -
Résumé du contenu de la page N° 12
Multi-purpose Digital Camera Pan/Tilt Head Compatible System Configuration Remote controllable lens HD-SDI Coaxial Cable (5C-FB) Multi-cable (5m) Multi-purpose Digital AK-HDMLTCA05 Remote Camera AK-HC910L (zoom/focus control) cable HD Monitor AC adapter AW-PS505A External sync signal (3 value sync) Pan/tilt head AW-PH400 DC Power Cable Pan/tilt head control panel Camera Controller AW-RP400 AK-HRP900L AC adapter AW-PS505A - 12 -
Résumé du contenu de la page N° 13
Operation Procedure 1 Turn on the power of each 5 Adjust the black balance. equipment. • This adjustment is needed when the camera is used for the first time or 2 Properly adjust the light for the after leaving unused for a long time. object. • The adjustment is necessary when the ambient temperature is greatly 3 Adjust the flange back of the lens, changed or at the change of season. the iris and the focus. • After adjusting the black balance once, re-adjustment is not needed • Flange back must
Résumé du contenu de la page N° 14
How to Adjust _ Flange back adjustment (for zoom lens) The adjustment is to adjust the focus in all the range from the maximum zoom to the widest angle of the zoom lens. 1 Shoot a dark object to open the iris. 2 Adjust the distance from the object to 2m at least, then loosen the flange back fixing knob of the lens. 3 Set the lens to the maximum zoom and adjust the focus by turning the focus ring. 4 Set the lens to the widest angle and adjust the focus by turning the flange back adjust ring. 5 Re
Résumé du contenu de la page N° 15
How to Adjust _ White balance adjustment Adjust the white balance after shooting a white object by at least 50% of the screen. NOTE: If the white signal level is over 100% or less than 50%, the white balance may not be normally adjusted. _ Colour temperature and white balance adjustment (reference) When carbon is burnt, it develops 10000K Blue sky various colours of light depending on the temperature. Natural light can be 9000K Rainy specified by colour temperature reflecting to the colour devel
Résumé du contenu de la page N° 16
How to Adjust _ Black balance adjustment • Adjust it with the lens closed. When the motor drive lens is controlled from the camera, adjusting the black balance causes the lens to be automatically closed. _ Gen lock adjustment When multiple cameras are used or the camera is combined with other equipment, it is necessary to adjust the phase for phase matching by external synchronization. • Horizontal phase adjustment Observe the waveforms of externally synchronizing signal input (black burst signa
Résumé du contenu de la page N° 17
Setting of Menu Items _ Configuration of menu display screen Maintenance menu USER MENU Using condition setting menu Camera ID setting menu File managing & renewing menu - 17 -
Résumé du contenu de la page N° 18
Setting of Menu Items _ USER menu (Initial screen) The readout data at start of power supply is the data just before cutting off the power supply, and the operation is started with the data. 1. MAINTENANCE It sets various adjusting data. 2. SETTING It sets various modes. 3. CAM ID It sets the camera ID. 4. FILE MENU It executes file loading and saving, and makes the basic setting of data display. Menu operation is executed by the Camera Controller AK-HRP900L. - 18 -
Résumé du contenu de la page N° 19
Setting of Menu Items ! Maintenance menu • Move the cursor (arrow mark) to the item to be adjusted and press the MENU key, then it enters the adjustment menu thereunder. • Move the cursor to MAINTENANCE and press the MENU key, then it returns to USER MENU. 1 Black shading correction menu • When MENU key is pressed at DETECTION, (BLK-SHD:ACTIVE) appears, then the lens is automatically stopped down and ABB operation is executed. • When CORRECT (DIG) is turned ON, horizontal and vertical shading co
Résumé du contenu de la page N° 20
Setting of Menu Items ! Maintenance menu 2 Pedestal, gamma, flare adjustment menu M PED: Master pedestal can be adjusted only by turning the control panel VR. The R, G, B pedestal can be totally adjusted. R, B PED: R, B pedestal adjustment. Besides the master pedestal adjustment, R, B pedestal can be independently adjusted. It is not related to DATA REF. The numeral display after normal ending of ABB is “0” for both of R, B. M GAMMA: Master gamma adjustment. The R, G, B gamma can be totally adju
