Résumé du contenu de la page N° 1
4
5
USER GUIDE
NI Smart Camera I/O Accessory
This document describes the features of the NI Smart Camera I/O Accessory, what you need to get
started, installation and operation instructions, and accessory specifications.
The NI Smart Camera I/O Accessory features the following:
• Spring terminals for two isolated inputs
� Spring terminals for two isolated outputs
� Spring terminals for the quadrature encoder inputs
� Two power connection options
� An RS-232 connector to communicate with the sma
Résumé du contenu de la page N° 2
What You Need to Get Started ❑ NI Smart Camera I/O Accessory kit, which includes the accessory, 15-pin D-SUB female to 15-pin D-SUB male cable, 2 m (part number 197817-02), and two-position header connector (Wago part number 734-102, available from www.wago.com) ❑ NI 17xx Smart Camera ❑ One of the following power supply options: Caution Use the smart camera only with a 24 VDC, UL listed, limited power source (LPS) supply. The power supply will bear the UL listed mark, LPS. The power supply m
Résumé du contenu de la page N° 3
Operate the device only at or below Pollution Degree 2. Pollution is foreign matter in a solid, liquid, or gaseous state that can reduce dielectric strength or surface resistivity. The following is a description of pollution degrees: � Pollution Degree 1 means no pollution or only dry, nonconductive pollution occurs. The pollution has no influence. � Pollution Degree 2 means that only nonconductive pollution occurs in most cases. Occasionally, however, a temporary conductivity caused by cond
Résumé du contenu de la page N° 4
Installation To get started with the NI 17xx Smart Camera I/O Accessory, complete the following steps while referring to Figure 1. If you have not already installed the NI Smart Camera and required software, refer to Getting Started with the NI 17xx Smart Camera for instructions. Note For EMC compliance, operate this device with shielded cables. Caution Never touch the exposed pins of connectors. Connect the Camera Cable Connect the 15-pin D-SUB female to 15-pin D-SUB male cable to the CAMERA
Résumé du contenu de la page N° 5
Apply Power When power is first applied to the smart camera, the POWER LED flashes red for one second while internal systems power up. The POWER LED then lights green when power is correctly wired to the smart camera. If the smart camera does not power up, check all connections and the power in selection switch position, then check the power fuse, as described in the Fuses section. Building a Custom Power Cable If you are using a power supply other than the NI desktop power supply, you must b
Résumé du contenu de la page N° 6
2. Wire the voltage output of the 24 VDC +20%/–15% (IEC 1311) power supply to the main voltage input on the two-position connector as shown in Figure 3. Insert a small flathead screwdriver into the square opening. Using the screwdriver as a lever to open the clamp, insert the wire into the spring terminal opening. Remove the screwdriver to securely clamp the wire. COM +24 VDC Figure 3. Power Two-Position Header Wiring Diagram 3. Wire the common signal (ground) output of the power supply to t
Résumé du contenu de la page N° 7
NATIONAL INSTRUMEN NI SMART CAMERA I/O ACCESSORY Replacing Fuses To replace a blown fuse on the accessory, complete the following steps. 1. Unplug the accessory power. 2. Remove all signal wires and cables from the accessory. 3. Unscrew the two screws from a side panel with a Phillips head screwdriver and remove the side panel as shown in Figure 4. Figure 4. Removing the Circuit Board 4. Slide the circuit board out. 5. Replace the blown fuse while referring to Figure 1 for the fuse location.
Résumé du contenu de la page N° 8
Specifications This section lists the specifications of the NI Smart Camera I/O Accessory. These specifications are typical at 25 °C, unless otherwise noted. Note Refer to the NI 17xx Smart Camera User Manual for specifications about signals. Power Requirement Supply voltage .......................................................24 VDC +20%/–15% (IEC 1311) Current requirement...............................................Refer to the specification for your NI Smart Camera Physical Dimensions ..
Résumé du contenu de la page N° 9
CE Compliance The NI Smart Camera I/O Accessory meets the essential requirements of applicable European Directives, as amended for CE marking, as follows: � 2006/95/EC; Low-Voltage Directive (safety) � 2004/108/EC; Electromagnetic Compatibility Directive (EMC) Note Refer to the Declaration of Conformity (DoC) for this product for any additional regulatory compliance information. To obtain the DoC for this product, visit ni.com/certification, search by model number or product line, and click t
Résumé du contenu de la page N° 10
Where to Go for Support The National Instruments Web site is your complete resource for technical support. At ni.com/support you have access to everything from troubleshooting and application development self-help resources to email and phone assistance from NI Application Engineers. A Declaration of Conformity (DoC) is our claim of compliance with the Council of the European Communities using the manufacturer’s declaration of conformity. This system affords the user protection for electroni
Résumé du contenu de la page N° 11
National Instruments, NI, ni.com, and LabVIEW are trademarks of National Instruments Corporation. Refer to the Terms of Use section on ni.com/legal for more information about National Instruments trademarks. Other product and company names mentioned herein are trademarks or trade names of their respective companies. For patents covering National Instruments products/technology, refer to the appropriate location: Help»Patents in your software, the patents.txt file on your media, or the Nat
