Résumé du contenu de la page N° 1
INSPECTION CAMERA 2.4” lCd
66550
SET uP ANd OPERATINg INSTRuCTIONS
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE ThIS MANuAl.
© ®
Copyright 2008 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be
Résumé du contenu de la page N° 2
NOTICE is used to SAVE ThIS MANuAl address practices Keep this manual for the safety warn- not related to personal injury. ings and precautions, assembly, operat- CAuTION, without ing, inspection, maintenance and cleaning the safety alert procedures. Write the product’s serial symbol, is used to address number in the back of the manual near the practices not related to assembly diagram (or month and year of personal injury. purchase if product has no number). Keep this manual and
Résumé du contenu de la page N° 3
ranges and refrigerators. There is must be ANSI-approved and breath- an increased risk of electric shock if ing protection must be NIOSH-ap- your body is grounded. proved for the specific hazards in the work area. c. do not expose power tools to rain or wet conditions. Water entering 4. Power tool use and care a power tool will increase the risk of a. do not force the power tool. use electric shock. the correct power tool for your ap- 3. Personal safety plication. The correct power tool
Résumé du contenu de la page N° 4
5. Battery tool use and care 4. Wear ANSI-approved safety goggles during use. a. Recharge only with the charger specified by the manufacturer. A 5. Position batteries in proper polarity charger that is suitable for one type of and do not install batteries of differ- battery pack may create a risk of fire ent types, charge levels, or capacities when used with another battery pack. together. b. Use the Camera only with specifi- 6. Maintain labels and nameplates on cally designated battery
Résumé du contenu de la page N° 5
cause cancer, and birth defects or other reproductive harm. Wash hands after handling. (California Health & Safety Code § 25249.5, et seq.) 12. The warnings, precautions, and in- structions discussed in this instruction manual cannot cover all possible con- ditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. 13. This device complies with par
Résumé du contenu de la page N° 6
including HVAC inspection, automotive/ SPECIFICATIONS boat/aircraft inspection, cable routing, etc. CAMERA TO PREVENT INjuRY FROM 704x576 (PAL); Total Pixels 712x486 (NTSC) ACCIdENTAl OPERATION: Turn the Power Switch on the Modulation Type FM Control handle and Monitor to Bandwidth 18MHz “OFF” position and unplug Power Supply 4 AA batteries the Adaptor from its electrical MONITOR outlet before performing any adjustments, inspection, LCD Screen Type 2.36”TFT-LCD maintenance, or clean
Résumé du contenu de la page N° 7
b. Slide knurled knob on Control Work Piece and Work Area Set up Handle up to threaded section on 1. Designate a work area that is clean Camera cable and finger tighten to and well-lit. The work area must not secure Camera cable in place. allow access by children or pets to prevent injury and distraction. 2. When recharging the Monitor, keep the Monitor close to the Adaptor so that the cord does not present a trip- 3. To attach Hook (4), Magnet (5), or ping hazard. Mirror (6) to Camera
Résumé du contenu de la page N° 8
power light on top of Control Handle To use With T.V. or Monitor will be lit. Use this dial to adjust the The Inspection Camera may be used brightness of LEDs near Camera. with a T.V. or Monitor by connecting 3. Slide ON/OFF switch on right side of the mini plug of the Extension Cable Monitor (3) to “ON” position. Press (9) to the video “OUT” jack. Next the POWER button on Monitor. connect the RCA plug to the video Power Light on Monitor will be green “IN’ jack on your T.V. or Monitor. a
Résumé du contenu de la page N° 9
2. AFTER uSE, clean external surfaces MAINTENANCE ANd of the tool with clean cloth. SERVICINg 3. WARNINg! If the supply cord of Procedures not specifically the adaptor is damaged, it must be explained in this manual replaced only by a qualified ser- must be performed only by a vice technician. qualified technician. Charging Monitor TO PREVENT INjuRY FROM Adapter Cable (7) ACCIdENTAl OPERATION: Turn the Power Switch of the Monitor to its “OFF” position Monitor (3) Adapter (8) and
Résumé du contenu de la page N° 10
Troubleshooting Problem Possible Causes likely Solutions Tool will not start. 1. Monitor not charged. 1. Charge Monitor. 2. Batteries need changing. 2. Replace batteries in Control Handle. Monitor will not 1. Cable not attached properly. 1. Make sure Adapter Cable is connected charge. between Monitor and Adapter. 2. Adapter not connected to power. 2. Make sure Adapter is securely plugged into wall socket. Image too dark or 1. LEDs near camera need 1. Use dial on Control Handle to adjust ligh
Résumé du contenu de la page N° 11
PARTS lIST Part description Qty. 1 Control Handle 1 2 Mini Camera with Cable 1 3 Monitor 1 4 Hook 1 5 Magnet 1 6 Mirror 1 7 Adapter Cable 1 8 Adapter 1 9 Extension Cable 1 ASSEMBl Y dIAgRAM 1 2 8 6 5 4 9 7 3 Record Product’s Serial Number here: Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not avail- able individually as replacement parts. SKU 66550 For technical questions, please c
Résumé du contenu de la page N° 12
lIMITEd 90 dAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installati
