Instruction d'utilisation Audiovox CCDF

Résumé du contenu de la page N° 1

Installation Instructions
Model CCDF
Color Camera External Mount
CCDF FEATURES:

High Resolution, 1/3”CCD Color Camera

Compact Zinc Alloy Die Cast Body

Waterproof Housing

Waterproof Microphone

Adjustable Mounting Angle

Wide Angle Lens

Flush Mount or Surface Mount
128-6951
1 of 12

Résumé du contenu de la page N° 2

Color Camera View: Cable Connector End View: 1 128-6951 2 of 12

Résumé du contenu de la page N° 3

Specifications: 1. Signal System: NTSC 2. Voltage: DC12V 3. Current: 80mA 4. Image Sensor: 1/3” CCD Color Sensor NTSC: 510 X 492 picture elements 5. Horizontal Definition: 420 Lines 6. Viewing Angle: 120 degrees 7. Minimum Illumination: 0.8 LUX 8. Outer Dimensions: 1.18”(W) x 1.10”(H) x 1.65”(D) 9. Weight: 2.5 Oz 2 128-6951 3 of 12

Résumé du contenu de la page N° 4

Contents: 3 128-6951 4 of 12

Résumé du contenu de la page N° 5

Contents Description: 1. Camera: 1 8. Slant Washer 1: 1 2. Support Bracket: 1 9. Slant Washer 2: 1 3. Lock Nut: 1 10. Tapping Screw: 2 4. Protective Cover: 1 11. Combine Screw: 2 5. Top Cover: 1 12. Washer: 2 6. Flat Washer 1: 1 13. Docking Nut: 2 7. Flat Washer 2: 1 4 128-6951 5 of 12

Résumé du contenu de la page N° 6

Flush Mount Note: 1. Camera 3. Lock Nut 5. Top Cover 6. Flat Washer 1 14. Mounting Plate 5 128-6951 6 of 12

Résumé du contenu de la page N° 7

Flush Mount Installation: 1. Select a suitable mounting location in the rear center of vehicle. Check behind panel for wire routing access and confirm that the drill will not damage any existing components. Use a 7/8” hole saw to drill the mount ing hole. 2. Screw the lock nut with the threaded side toward the camera body in the showed direction, then put the camera neck through the mounting hole with the lens exposed and wire cable facing down. 3. Place the flat washer 1 (# 6) and top cover (#

Résumé du contenu de la page N° 8

Angle Flush Mount Size of Mounting Holes (See the Attached Page) Note: 1. Camera 3. Lock Nut 5. Top Cover 7. Flat Washer 2 8. Slant Washer 1 9. Slant Washer 2 7 128-6951 8 of 12

Résumé du contenu de la page N° 9

Angle Flush Mount Installation: 1. Select a suitable mounting location in the rear center of vehicle. Check behind panel for wire routing access and confirm that the drill will not damage any existing components. Drill four 1/8” positioning holes and one 7/8” mounting hole at the mounting location according to the drawing of Size of Mounting Holes. 2. Screw the lock nut (# 3) and the flat washer 2 (# 7) with the non-threaded side to the camera neck in the showed direction. 3. Mount the slant was

Résumé du contenu de la page N° 10

Surface Mount Note: 1. Camera 2. Support Bracket 3. Lock Nut 4. Protective Cover 5. Top Cover 6. Flat Washer 1 11. Combine Screw 12. Washer 13. Docking Nut 9 128-6951 10 of 12

Résumé du contenu de la page N° 11

Surface Mount Installation: 1. Locate suitable mounting location in the rear center of the vehicle and use the support bracket (# 2) as a template to mark and drill two 5/32” holes on the mounting location. 2. Put the support bracket (# 2) onto the camera neck, then screw the lock nut along the camera neck to secure the bracket (# 2) to the camera body (# 1) in the showed direction. 3. Screw the combine screws (or tapping screws) into the holes to attach the camera support bracket to the vehicle

Résumé du contenu de la page N° 12

© 2004 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, N.Y. 11788 128-6951 128-6951 12 of 12