Résumé du contenu de la page N° 1
Digital Laser Copier/Printer
Operation Manual
MODEL
AL-1340
Résumé du contenu de la page N° 2
FOR YOUR PROTECTION... To aid in reporting this compact copier in case of loss or theft, please record below the model number and serial number located on the back of the unit. We also suggest you record all the information listed and retain for future reference. MODEL NUMBER SERIAL NUMBER DATE OF PURCHASE Dealer Address City State Zip Telephone Service Station Address
Résumé du contenu de la page N° 3
CONTENTS 1 GETTING STARTED INTRODUCTION 3 CAUTIONS 3 MAIN FEATURES 4 PART NAMES 6 OPERATION PANEL 7 2 INSTALLATION COPIER INSTALLATION 8 CAUTIONS ON HANDLING 9 CHECKING PACKED COMPONENTS AND ACCESSORIES 10 UNPACKING 10 REMOVING PROTECTIVE PACKING MATERIALS 11 INSTALLING THE TD CARTRIDGE 11 LOADING COPY PAPER (installing the paper tray) 13 POWER TO COPIER 15 POWER ON 16 – Initial settings of operation panel 16 3 MAKING COPIES PAPER 1
Résumé du contenu de la page N° 4
CONTENTS 5 SUPPLIES AND USER MAINTENANCE TD CARTRIDGE REPLACEMENT 26 DRUM CARTRIDGE REPLACEMENT 27 USER MAINTENANCE 28 – Cabinet 28 – Original table and original cover 29 – Transfer charger 29 – When copier is not in use 30 6 COPIER TROUBLE? MISFEED REMOVAL 31 – A Misfeed in the paper feed area 31 – B Misfeed in the fusing area 32 – C Misfeed in the transport area 33 TROUBLESHOOTING 34 STATUS INDICATORS 35 DISPLAYING TOTAL NUMBER OF COPIES
Résumé du contenu de la page N° 5
Getting started GETTING STARTED 1 This chapter provides basic information for using the copier. 1 INTRODUCTION This copier has been designed to provide intuitive operating ease while requiring a minimum amount of space. To get full use of all copier features, be sure to familiarize yourself with this manual and the copier. For quick reference during copier use, keep this manual in a handy location. This copier can be used as a laser printer. This manual describes only the copier features. For de
Résumé du contenu de la page N° 6
Getting started CAUTIONS Place the copier on a firm, level surface. Do not install the copier in a humid or dusty location. When the copier is not used for long time, for example for consecutive holidays, turn the power switch off and remove the power cord from the outlet. When moving the copier, be sure to turn the power switch off and remove the power cord from the outlet. 1 Do not cover the copier with a dust cover, cloth or plastic film while the power is on. Doing so may prevent h
Résumé du contenu de la page N° 7
Getting started MAIN FEATURES Substantial copying functions Zoom copying from 50% to 200% in 1% increments can be performed. Continuous copying of maximum 99 sheets can also be performed. Toner save mode reduces toner consumption by approximately 10%. User programs allow setting/modification of functions for customer’s needs. 1 Scan once/ Print many This copier is equipped with a 1-page memory buffer. This memory allows the copier to scan an original 1 time only and make up to 99 copie
Résumé du contenu de la page N° 8
Getting started PART NAMES Original table Original cover 1 Operation Side cover panel Manual bypass Paper tray Paper guides Side cover Handle Front cover open button Paper output tray Paper output tray Parallel interface connector extension Power cord socket Handle Power switch TD cartridge lock release Drum cartridge button Drum cartridge handle TD cartridge Transfer charger Paper feed roller Fusing unit Charger cleaner release lever 6
Résumé du contenu de la page N° 9
Getting started OPERATION PANEL 200% MAX. 129% 1 x 1 1 x 5/2 8/2 8/2 11 100% 100% 1 78% 1 x 1 x 8/2 14 8/2 11 1 x 1 x 1 64% 8/2 11 5/ 8/ 2 2 ZOOM 50% MIN. Exposure mode selector key and Display indicators Displays the specified copy quantity, zoom Use to sequentially select the exposure copy ratio, user program code, and error modes: AUTO, MANUAL or PHOTO. code. Selected mode is shown by a lit indicator. (p. 20) ON LINE indicator Lights up when the machine is used as a Light and dark keys and ex
Résumé du contenu de la page N° 10
Installation INSTALLATION 2 Follow the installation procedure below to use the copier properly. COPIER INSTALLATION 2 Improper installation may damage the copier. Please note the following during initial installation and whenever the copier is moved. If the copier is moved from a cool place to a warm place, condensation may form inside the copier. Operation in this condition will cause poor copy quality and malfunctions. Leave the copier at room temperature for at least 2 hours before use. Do no
Résumé du contenu de la page N° 11
Installation COPIER INSTALLATION 8" (20 cm) Be sure to allow the required space around the machine for servicing and proper 8" (20 cm) ventilation. 4" (10 cm) 4" (10 cm) A small amount of ozone is produced within the copier during operation. The emission level is insufficient to cause any health hazard. 2 NOTE: 3 The present recommended long term exposure limit for ozone is 0.1 ppm (0.2 mg/m ) calculated as an 8 hr. time-weighted average concentration. However, since the small amount that is emi
Résumé du contenu de la page N° 12
Installation CHECKING PACKED COMPONENTS AND ACCESSORIES Open the carton and check if the following components and accessories are included. Power cord Interface cable (IBM PC/AT or compatible computer) 2 Printer driver (CD-ROM) Operation manual Copier TD cartridge Drum cartridge (installed in copier) If anything is not included or is damaged, contact our Technical Assistance Department at 1-(630)378-3590 in the USA or 1-877-SHARP-CC (toll free)/ 905-568-7140 in Canada. Save the carton and p
Résumé du contenu de la page N° 13
Installation REMOVING PROTECTIVE PACKING MATERIALS Remove pieces of tape , , , , and and protective cover . Then open the 1 original cover and remove protective materials and . c g h a e f d 2 b Use a coin (or suitable object) to remove the screw. 2 Store the screw in the paper tray because it will be used if the copier has to be moved. (p. 14) INSTALLING THE TD CARTRIDGE Open the side cover while pressing the side cover open button. 1 11
Résumé du contenu de la page N° 14
Installation INSTALLING THE TD CARTRIDGE Remove the CAUTION tape from the front cover and remove the two protective pins 2 from the fusing unit by pulling the strings upward one at a time. 2 CAUTION tape Protective pins Push gently on both sides of the front cover to open the cover. 3 Remove the TD cartridge from the bag. Remove the protective paper. Hold the cartridge 4 on both sides and shake it horizontally four or five times. 4 or 5 times Hold the tab of the protective cover and pull the tab
Résumé du contenu de la page N° 15
Installation INSTALLING THE TD CARTRIDGE Gently insert the TD cartridge until it locks in place. 6 2 Close the front cover and then the side cover by pressing the round projections near 7 the side cover open button. When closing the covers, be sure to close the front cover securely and then close the side cover. If the covers are closed in the wrong order, the covers may be damaged. LOADING COPY PAPER (installing the paper tray) Raise the handle of the paper tray and pull the paper tray out unti
Résumé du contenu de la page N° 16
Installation LOADING COPY PAPER Remove the pressure plate lock. Rotate the pressure plate lock in the direction of the 2 arrow to remove it while pressing down the pressure plate of the paper tray. 2 Store the pressure plate lock which has been removed in step 2 and the screw which 3 has been removed when unpacking (see page 11, step 2 of REMOVING PROTECTIVE PACKING MATERIALS) in the front of the paper tray. To store the pressure plate lock, rotate the lock to fix it on the relevant location. Pr
Résumé du contenu de la page N° 17
Installation LOADING COPY PAPER Gently push the paper tray back into the copier. 6 After loading copy paper, to cancel the blinking “P” without restarting copying, press the clear ( ) key. The “P” in the display will go out and the ready ( ) indicator will light up. 2 POWER TO COPIER Ensure that the power switch of the copier is in the OFF position. Insert the attached 1 power cord into the power cord socket at the rear of the copier. If you use the copier in a country other than the country wh
Résumé du contenu de la page N° 18
Installation POWER ON Turn the power switch on the left side of the copier to the “ON” position. The ready ( ) indicator will light up and other indicators which show the initial settings of the operation panel will also light up to indicate the ready condition. For the initial settings, see the “Initial settings of operation panel” described below. The copier will enter a power save mode once the set time has elapsed without any copier operation after the last copy of a run is made or power i
Résumé du contenu de la page N° 19
Making copies MAKING COPIES 3 This chapter describes basic copying functions and some other copying functions using the manual bypass. PAPER For best results, use only paper recommended by SHARP. Type of paper Type of media Size Weight 3 feeding Paper tray Standard paper Letter (8-1/2" x 11") 15 lbs. to 21 lbs. Legal (8-1/2" x 14") Invoice (5-1/2" x 8-1/2") A4 (210mm x 297mm) B5 (182mm x 257mm) A5 (148.5mm x 210mm) Manual bypass Standard paper and Letter (8-1/2" x 11") 14 lbs. to 34.5 thick pape
Résumé du contenu de la page N° 20
Making copies NORMAL COPYING Ensure that paper of the desired size is set in the paper tray. See page 13, LOADING 1 COPY PAPER. When copying onto 8-1/2" x 11" paper or a larger size, pull out the paper output tray extension. Turn the power switch on. 2 3 Open the original cover. 3 Place the original face down on the original table. Align it with the original scale and 4 the centering ( ) mark. Original scale mark Gently close the original cover. When copying a book or an original which has been
