Résumé du contenu de la page N° 1
OWNER'S MANUAL
34CM CORDLESS REMOTE COLOUR TELEVISION
MODEL: 3498
Type Tested
Electrical
Safety
AS/NZS 3250 Lic 4163
Standards Australia
APP No: CS6809N
PALSONIC CORPORATION PTY LTD
1 JOYNTON AVENUE
WATERLOO NSW 2017 AUSTRALIA
TEL:(02)9313 7111
FAX:(02)9313 7555
www.palsonic.com.au
PALSONIC CUSTOMER SERVICE
TELEPHONE
AUSTRALIA:1300 657 888
Résumé du contenu de la page N° 2
This equipment has been designed and manufactured to meet the highest international standards, but, like any electrical apparatus which is operated at mains voltage, care must be taken if you are to obtain the best results and safety is to be assured. This is particularly important with audio and TV equipment. DO read this handbook carefully and keep it handy for ready reference. ensure that all electrical connections (including the mains plug, extension leads and DO interconnections between pie
Résumé du contenu de la page N° 3
PRESET DOOR POWER SWITCH AUDIO IN VIDEO IN ANTENNA SPEAKER INSIDE THE PRESET DOOR SKIP - MT + PRESET AUTO - VOL + - CH + STAND BY MUTE TV/AV CHANNEL SELECTOR PREVIOUS CHANNEL SELECTOR CALL VOLUME CONTROL SLEEP TIME PICTURE PICTURE/TIME TIMER 2 LED REMOTE SENSOR INDICATOR
Résumé du contenu de la page N° 4
INSTALLING BATTERIES: 1. Remove the battery cover of Remote Control Unit. 2. Insert two "AA" 1.5V batteries making sure the polarity (+ or -) of the batteries matches the polarity marks inside the unit. 3. Close the battery cover. * When the Remote Control Unit is not used for a long time or the batteries are worn out, take out the batteries to prevent electrolyte leakage. * Take care not to drop, dampen, disassemble the Remote Control Unit. * Operatable remote contro
Résumé du contenu de la page N° 5
. Use the CHANNEL SELECTOR button on the Remote Control Unit to select channel 1) 0-9 channel 6 6 2) 10-19 channel 12 1- 1- 2 3) 20-29 channel 28 2- 2- 8 4) 30-39 channel 35 3- 3- 5 5) 40-49 channel 48 4- 4- 8 6) 50-59 channel 59 5- 5- 9 4
Résumé du contenu de la page N° 6
NOTE: To select two digit channel, the second digit must be pressed within 2 seconds. * PREVIOUS BUTTON (REMOTE CONTROL UNIT) Pressing this button to select the channel that was tuned immediately before the one being watched. For example: If you are watching the program on channel 6, and the previous program you watched is on channel 15; then you can press the button to reach channel 15, press it again to return channel 6. 6 15 CHANNEL PRESET . AUTO PRESET 1. Press the PSET (PRESET ON/OFF) butt
Résumé du contenu de la page N° 7
4. Press PRESET ON/OFF button to exit preset mode. The searched program station has been memorised at the present channel position, 5. Repeat 1~ 4 steps to search another channel. NOTE : * If the same channel position is selected during repeat operation, the former memory will be erased. * If some channel position is tuned by MANUAL TUNING mode, AFC (automatic frequency control) function is defeated in this channel position. SKIP BUTTON: . FU
Résumé du contenu de la page N° 8
PICTURE CONTROL (REMOTE CONTROL UNIT) . Press the PICTURE CONTROL button on the Remote Control Unit. The FUNCTION to be adjusted is selected in sequence as shown in the following chart at every press of the button. BRIGHTNESS CONTRAST COLOUR . Adjust the button to obtain satisfactory picture. ON SCREEN DISPLAY Red Block Moves CAPTION FUNCTION DISPLAY Press button Press button Contrast CONTRAST Strong Weak Brightness BRIGHTNESS Dark Light Colour COLOUR Pale Deep CALL BUTTON (
Résumé du contenu de la page N° 9
SLEEP BUTTON (REMOTE CONTROL UNIT) . Using SLEEP button allows you to have the appliance automatically turned off a predetermined time, and set the appliance to stand by mode. Press SLEEP again SLEEP 0 SLEEP 90 (RED) (GREEN) Decrease 10 minutes at every press SLEEP 10 (GREEN) . After the SLEEP function is set, the remaining time will be automatically displayed for 4 seconds every ten minutes. * If you press STAND BY button while the SLEEP function is operating, the SLEEP function will be can
Résumé du contenu de la page N° 10
. ON TIME OPERATION: 1. Set the CLOCK in operation mode. 2. Press the TIMER button until "ON TIME" displays on the screen. 3. Press the button to select the exact hour when you want to turn on the appliance. Press the button to select the exact minute when you want to turn on the appliance. 4. Press the CHANNEL SELECTOR to set your desired channel. TIME 1 ON TIME 8 ON TIME AM 12 : 00 PM 7 : 00 5. Press TIME button, the CLOCK indicator is green instead of red ON TIME function star
Résumé du contenu de la page N° 11
TROUBLE SHOOTING GUIDE Many apparent malfunctions may be caused by slight misadjustment of regular controls or some other equally similar simple causes. If any problem arises in the operation of your set, first check through this list of symptoms and correction. Should the problem be unsettled, unplug the set and contact your dealer. Symptoms Check these things Try these adjustment . . Press POWER BUTTON Be sure power cord is plugged in. . No picture, . . Try another channel. May be station tro
Résumé du contenu de la page N° 12
SPECIFICATIONS: : CCIR PAL B/G Colour System : 625 Lines; Horizontal 15625Hz; Vertical 50Hz Scanning : VHFL 0-3; VHFH 4-11; UHF 21-69 Receivers Channel : S1-S41 Cable Channel : Video 38.9MHz; Sound 33.4MHz; Chroma 34.47MHz IF Frequency : 5.5MHz Inter Carrier Frequency : AC 220-240V, 50 HZ Power supply : 34cm Diagonal / 90 Deflection Angle CRT : 1.5W Max ; 1.0W 10% THD Audio Output : VHF/CATV/UHF 75 ohm Antenna Impedance : 361 (W) x 344 (H) x378 (D) Dimension (mm) : 11 kg Weight Remote Control Un
Résumé du contenu de la page N° 13
PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL:(02)9313 7111 FAX:(02)9313 7555 www.palsonic.com.au PALSONIC CUSTOMER SERVICE TELEPHONE AUSTRALIA: 1300 657 888 604-37823-10
