Instruction d'utilisation AT&T E580-1

Résumé du contenu de la page N° 1

ATT-580-1CIB-d2.qxd 1/17/2004 6:12 PM Page 1
User Manual (Part 2)
5.8 GHz Expansion
Handset E580-1
For use with AT&T models
E5860 • E5865 • E5900B • E5965C

Résumé du contenu de la page N° 2

ATT-580-1CIB-d2.qxd 1/17/2004 6:12 PM Page 2 You must charge See pages 2-3 batteries and register the STOP! for easy instructions. handset before use. For customer service or product Please also read information, visit our web site at Important Product Information www.telephones.att.com Enclosed in product package. or call 1-800-222-3111. Table of contents Before you begin........................................1 Parts checklist.............................................1 Battery installat

Résumé du contenu de la page N° 3

ATT-580-1CIB-d2.qxd 1/17/2004 6:12 PM Page 1 Before you begin This cordless telephone operates with If you move out of range during a the maximum power allowed by the phone conversation, you might hear Federal Communications Commission noise or interference. To improve (FCC). Even so, the handset and base reception, move closer to the base. can communicate over only a certain If you move out of range without distance — which can vary with the pressing OFF, your phone will be left locations o

Résumé du contenu de la page N° 4

ATT-580-1CIB-d2.qxd 1/17/2004 6:13 PM Page 2 Battery installation & charging After installation, place the handset in the charger and allow batteries to charge for 12 hours before use. You can keep batteries charged by returning the handset to the charger after each use. When battery power is fully depleted, a full recharge takes about 8 hours. 1 LOW BATTERY REDIAL 2:10 PM CID LOG Low battery indicator Return handset to charger to recharge when this symbol flashes. (Handset will beep when bat

Résumé du contenu de la page N° 5

ATT-580-1CIB-d2.qxd 1/17/2004 6:13 PM Page 3 Registering the handset Before using your new handset, you must register it with the base. During registration, you must enter the 15-digit ID number of the telephone base. To find this number, go to the base, press MENU, scroll down to select DISPLAY MENU BASE ID, then press OK. The handset provided with your telephone is automatically registered as Handset 1. Additional handsets will be assigned numbers in the order they are registered (2, 3, 4,

Résumé du contenu de la page N° 6

ATT-580-1CIB-d2.qxd 1/17/2004 6:14 PM Page 4 Belt clip & optional headset Install belt clip as shown below if desired. For hands-free telephone conversations, you can use any industry standard 2.5 mm headset (purchased separately). For best results use an AT&T 2.5 mm headset. Snap belt clip into notches on side of handset. Rotate and pull to remove. Plug 2.5 mm headset into jack on side of handset (beneath small rubber cap). 4

Résumé du contenu de la page N° 7

ATT-580-1CIB-d2.qxd 1/17/2004 6:15 PM Page 5 Quick reference guide For complete instructions, please refer to the manual provided with your telephone. Up Select Left Right Down NavKey Softkeys Press center button to display menus. Press a softkey to select a menu item Press NavKey buttons to navigate displayed just above the key. through menus. Press center button to select menu item highlighted. Phone/Flash Off/Cancel Press to begin a call, then dial a number. During a call, press to hang u

Résumé du contenu de la page N° 8

ATT-580-1CIB-d2.qxd 1/17/2004 6:15 PM Page 6 www.telephones.att.com Copyright © 2004 Advanced American Telephones. All Rights Reserved. AT&T and the Globe Design are trademarks of AT&T Corp., licensed to Advanced American Telephones. Printed in China. Issue 1.2 AT&T 1/19/04.

Résumé du contenu de la page N° 9