Instruction d'utilisation AT&T 9105

Résumé du contenu de la page N° 1

User’s Manual
for Cordless Telephone 9105
Fold open this manual for information about
this telephone’s installation and operation.
Please read Part 1 — Important Product
Information, included in this package.
Part 2
© 1998 Philips Consumer Communications, L.P. All rights reserved.
Printed in Mexico. 848233458 Issue 1AT&T
I N S TA L L AT I O N
Belt Clip—
Slide over the
back of the handset
Changes channel.
until it snaps
firmly in place.
Handset
Volume Control
PHONE indicator
goes on while you

Résumé du contenu de la page N° 2

I N S TA L L AT I O N Standard power outlet Power cord Telephone line cord Telephone jack Strain relief hook Power jack Telephone jack Slots Base unit Slots 1 Setting up the Cordless Telephone 9105. • Choose an area near an electri- Tabs cal outlet and a telephone jack. • The outlet should not be controlled by a wall switch. 2 Connect the telephone line cord. • Insert one end of the telephone line cord into the jack at the rear of the base unit. Plug the Reversible base other end into a telepho

Résumé du contenu de la page N° 3

I N S TA L L AT I O N c o n t i n u e d 6 Charge the handset batteries Wall Mounting 4 Connect the telephone line cord. before use. • Using the short telephone line 1 Choose a spot where the Place the handset face down in the cord supplied, insert one end of telephone wall jack is near an base unit cradle. Make sure that the telephone line cord into the electrical outlet. the IN USE/CHARGE light on the telephone jack on the rear of This phone requires a modular base is on. The handset battery t

Résumé du contenu de la page N° 4

TELEPHONE OPERAT I O N I M P O RT A N T: W h e n ever the handset Redial Turning Off the Ringer b at t e ries are re m ov e d, the handset To redial the last number dialed from To turn off the ringer on the handset, must be placed in the base unit cr a d l e the handset: do the following: for r e i n i t i a l i z ation. The IN USE/ 1 Press . 1 Press . CHARGE indicator on the base unit 2 Wait for the PHONE indicator to 2 Press . will flash during the initializa t i o n . go on and check for dial

Résumé du contenu de la page N° 5

M E M O RY Memory Features Memory Card To insert a pause in a stored nu m b e r, p ress and hold down the key that This telephone can store 10 tele p h o n e There is a memory card with an comes befo re the pause, until you hear nu m b e rs , e a ch up to 16 digits long. erasable surface located on the a second beep. This inserts a 2-second base to record names or telephone Numbers will remain stored in pause after that digit. To insert a numbers of the numbers stored in memory unless you eras

Résumé du contenu de la page N° 6

B AT T E R I E S About the Handset Batteries • Charge the battery provided with Spare Battery Charger or identified for use with this You will know the batteries need The Cordless Telephone 9105 is product only in accordance with charging when: equipped with a spare battery charger the instructions and limitations built-in to the base unit. The spare • The phone beeps two times when specified in this manual. battery charger allows you to always you press to answer or • O b s e rve proper polarit

Résumé du contenu de la page N° 7

I N C A S E O F D I F F I C U LT Y If you have difficulty operating If you get a four-beep signal when • Place the handset in the base, this phone, try the suggestions you try to use the handset: and check to make sure that the below. If you still have trouble, call IN USE/CHARGE indicator is on. The four-beep signal means that 1 800 722-9125. Unplug the AC adapter from the the handset and base are not outlet, wait 15 seconds, and then communicating properly. This If the phone does not work a

Résumé du contenu de la page N° 8

I N C A S E O F D I F F I C U LT Y c o n t i n u e d • The layout of your home or office • The base and handset may not may be limiting the operating be set to the same security code. range. Try moving the base to Place the handset in the base for another location—preferably on an at least 15 seconds to reset the upper floor. security code. See “If you get a four-beep signal.” If you lose a call after changing channels: If you are unable to operate special telephone services or other equip- Yo