Résumé du contenu de la page N° 1
B 99852G
Hob
User Manual
Résumé du contenu de la page N° 2
Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 350350 Installation This appliance must be installed and serviced by a competent person as stated in the Gas Safety ( Installation and Use) Regulations Current Editions and the IEE Wiring Regulations. For appliances installed in the Republic of Ireland please refer to NSAI-Domestic Gas Installations I.S.813 Current Editio
Résumé du contenu de la page N° 3
Ensure the control knobs are in the ‘OFF’ position when not in use. When using other electrical appliances, ensure the cable does not come into contact with the hot surfaces of the cooking appliance. Unstable or misshapen pans should not be used on the hob as unstable pans can cause an accident by tipping or spillage. Never leave the hob unattended when cooking with oil and fats. Never use plastic or aluminium foil dishes on the hob. Perishable food, plastic items and areosols may be affec
Résumé du contenu de la page N° 4
Contents Instructions for the User Important Safety Information 2 Description of the Hob 5 Operation 6 Maintenance and Cleaning 7 Something Not Working? 9 Service and Spare Parts 10 Customer Care 10 Guarantee Conditions 11 Instructions for the Installer Important safety requirements 13 Installation 14 Building In 15 Electrical connections 18 Wiring diagram 19 Fault Finding 20 Commissioning 23 Conversion from Natural Gas to LPG 24 Guide to Use the instructions The following symbols will be found
Résumé du contenu de la page N° 5
Description of the Hob 2 4 2 2 1 3 5 1. Hob Top 2. Semi-rapid Burners 3. Auxiliary Burner 4. Ultra-rapid Burner (triple crown) 5. Control knobs INSTALLATION Any gas installation must be carried out by a competent person, and in accordance with existing rules and regulations. The relevant instructions are to be found in the second section of this manual. Please, ensure that, once the hob is installed, it is easily accessible for the engineer in the event of a breakdown. WHEN THE HOB IS FIRST INST
Résumé du contenu de la page N° 6
Operation Hob burners To light a burner: Push in the relevant control knob and turn it to maximum position. Upon ignition, keep the knob pushed down about 5 seconds. This will allow the "thermocouple" (fig. 1 - letter D) to be heated and the safety device to be switched off, otherwise the gas supply would be interrupted. Then adjust the flame as required. If the burner does not ignite, turn the control knob to zero, and try again. Each control knob is equipped with a pilot light which gr
Résumé du contenu de la page N° 7
Maintenance and Cleaning Before any maintenance or cleaning YES can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob Top Regularly wipe over the hob top using a NO soft cloth well wrung out in warm water to which a little wasing up liquid has been added. Avoid the use of the following: - household detergent and bleaches; - impregnated pads unsuitable
Résumé du contenu de la page N° 8
Pan Supports To keep the pan supports in the correct position, they are mounted on metal pins located in the back of the hob. After cleaning the hob, ensure the pan supports are properly placed as shown in fig. 3. The pan supports are dishwasher proof. If washing them by hand, take care when drying them as the enamelling process occasionally leaves rough edges. If necessary, remove stubborn stains using a paste cleaner. The Burners The burner caps and crowns can be removed for cleaning. Wash the
Résumé du contenu de la page N° 9
Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Service Force Centre. SYMPTOM SOLUTION There is no spark when lighting the gas Check that the unit is plugged in and the electrical supply is switched on Check that the RCCB has not tripped (if fitted) Check the mains fuse has not blown Check the burner cap and crown have been replaced correctly, e.g. after cleaning. Check the main jet is not blocked and the
Résumé du contenu de la page N° 10
Service and Spare Parts If you require spare parts or an engineer contact your local Service Force Centre by telephoning: 0870 5 929 929 Your call will be routed to your local Service Force Centre. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www.serviceforce.co.uk For Customer Services in the Republic of Ireland please contact us at the address below: AEG-Electrolux Electrolux Groupl (Irl) Ltd Long Mile Road Dublin 1
Résumé du contenu de la page N° 11
Guarantee Conditions Standard guarantee conditions We, AEG-Electrolux, undertake that if within 12 months of the date of the purchase this AEG-Electrolux appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our discretion repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: • The appliance has been correctly installed and used only on the electricity or gas supply stated on the rating plat
Résumé du contenu de la page N° 12
Instructions for the Installer Instructions for the Installer Engineers technical data Overall dimensions Burner Dia. Tap By-pass 1/100 mm Width: 880 mm Depth: 510 mm Auxiliary 28 Semi-rapid 32 Cut out dimensions Ultra-rapid 56 Width: 830 mm Depth: 480 mm Aeration adjustment none Supply Connections Semi-rapid Burner 1.9 kW (6,483 BTU/HR) Gas: RC 1/2 inch (1/2 inch male) Rear right hand corner Auxiliary Burner 1.0 kW (3,412 BTU/HR) Electric: 230 V 50 Hz supply, 3 core flexible Appliance class 3
Résumé du contenu de la page N° 13
50 mm 100 mm 50 mm 100 mm 50 mm 50 mm Instructions for the Installer Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). For appliances installed in the Republic of Ireland please refer to NSAI- Domestic Gas Installation I.S. 813 Current Editions and the ETCI Rules for Electrical Installations. Detailed recommendations are contained in the following Britis
Résumé du contenu de la page N° 14
Instructions for the Installer Installation Important This hob must be installed by a competent person to the relevant Gas Standards. Any gas installation must be carried out by a registered competent person. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this book be ignored. On the end of the shaft, which includes the GJ 1/2" threaded elbow, adjustment is fixed so that the washer is fitted between the components
Résumé du contenu de la page N° 15
510 Instructions for the Installer Cut Out Size The dimensions of the cut-out are given in the diagram. FO 2349 Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. It is also recommended to carry out the electrical connection to the hob as shown in diagrams 1 and 2 (See next page). 15 880
Résumé du contenu de la page N° 16
Instructions for the Installer ON/OFF SWITCH ON/OFF SWITCH 1 2 FLEX OUTLET FLEX OUTLET FO 0764 FO 0763 Building over a kitchen unit with door Proper arrangements must be taken in designing the furniture unit, in order to avoid any contact with the bottom of the hob which 3 can be heated when it is operated. The recommended solution is shown in diagram 3. a 60 The panel fitted under the hob ("a") should be easily removable to allow easy access b if technical assistance is needed. The space behin
Résumé du contenu de la page N° 17
Instructions for the Installer Fitting the hob to the worktop Before fitting the hob into the cut out, an adhesive seal must be fitted to the underside outside edge of the hob. It is essential that no gaps are left in this seal in order to prevent spillage near the hob seeping into the cabinet below. 1) Remove the pan supports, the burners caps and crowns and turn the hob upside down, taking care the ignition electrodes are not damaged in this operation. 2) Place the sealing gasket all arou
Résumé du contenu de la page N° 18
Instructions for the Installer Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. This hob is designed to be connected to a 230-240V 50Hz AC electrical supply. Before switching on, make sure the electricity supply voltage is the same as that indicated o
Résumé du contenu de la page N° 19
Instructions for the Installer Permanent Connection In the case of a permanent connection, it is necessary that you install a double pole switch between the hob and the electricity supply (mains), with a minimum gap of 3 mm between the switch contacts and of a type suitable for the required load in compliance with the current electric regulations. The switch must not break the yellow and green earth cable at any point. Ensure that the hob supply cord does not come into contact with surfaces with
Résumé du contenu de la page N° 20
Instructions for the Installer Blue Brown Green Fault Finding Yellow Preliminary Electrical Systems Check START Blue Isolate appliance Green and carry out: Brown Yellow A: Earth Continuity check. Carry out: NO YES Carry out: D: Resistance to C: Polarity check. Earth check. Has inlet fuse blown? Electricity supply should now be satisfactory. NO YES PLUG (with cover removed) SOCKET (face view) Inlet wiring Earth Wire faulty. Green/Yellow ( ) Rectify any ( ) E fault. Neutral Wire Blue N L Isol
