Resumen del contenido incluido en la página 1
INSTRUCTIONS AND ADVICE FOR THE
USE, INSTALLATION AND MAINTENANCE
OF BUILT-IN ELECTRIC HOBS
Dear Customer,
Thank you for having purchased one of our products.
We are certain that this new, modern, functional and practical appliance, built with the very
highest quality materials, will meet your requirements in the best possible way. This hob is easy
to use. It is, however, important to thoroughly read the instructions in this handbook in order to
obtain the best results.
The manufacturer shall n
Resumen del contenido incluido en la página 2
DESCRIPTION OF THE HOT PLATES TYPE: PAZ 04 1 Normal plate Ø 145 of 1000 W 2 Normal plate Ø 180 of 1500 W 7 Control knob for electric plate n° 1 8 Control knob for electric plate n° 2 13 Warning light indicating that one or more plates are operating 2
Resumen del contenido incluido en la página 3
USE diagram indicates to which electric plate the knob in 1) SWITCHING ON THE ELECTRIC question corresponds (see fig. 1 - 2). PLATES A red warning light will come on to indicate that the The hobs may be equipped with three types of plate has been ignited. electric plates: normal, thermostat and rapid plates indicated by a red mark. The normal plates and the 2) HOW TO USE THE ELECTRIC PLATES rapid plates are controlled by a 7 - position switch A purely indicative plate regulation chart is given (
Resumen del contenido incluido en la página 4
USE WARNINGS: When the plate is switched on for the first time, or if it has remained unused for a long period, it should be dried for 30 minutes on switch position n° 1. This will eliminate any moisture that may have been absorbed by the insulating material. To correctly use the appliance, remember: - To place a pan on the plate before switching this on. - To always use pans with flat and very thick bottoms (see fig. 3). - To never use pans that are smaller than the plate diameters. - To dry th
Resumen del contenido incluido en la página 5
CLEANING WARNINGS: IMPORTANT: - Correctly preserve the plate after use by Always disconnect the appliance from the electricity main before carrying out any cleaning treating it with special products, easily operation. available on the market. This will keep the surface of the plate clean and bright. The 3) HOTPLATE operation will also prevent the formation of rust. If you want to preserve the surface clean and bright, - Any liquid overflowed the pans, must be periodically wash the hot plate with
Resumen del contenido incluido en la página 6
INSTALLATION Installation and maintenance must only be - Overturn the hob and correctly position seal “E” carried out by a qualified installer. (fig. 6) under the edge of the hob itself, so that Incorrect installation could cause damage to the outer part of the seal itself perfectly matches persons, animals and property for which the the outer perimetral edge of the hob. The ends of manufacturer cannot be held responsible. the strips must fit together without overlapping. - Evenly and securely f
Resumen del contenido incluido en la página 7
INSTALLATION When the appliance is connected straight to the 6) ELECTRICAL CONNECTIONS electricity main: Electrical connection must be carried out in compliance with the specifications and - Install an omnipolar cutout between the provisions in force. appliance itself and the main. This circuit-breaker should be sized according to the rating of the Before proceeding with the connections, check that: appliance and the opening between its contacts - The voltage rating of the appliance and the shou
Resumen del contenido incluido en la página 8
CONVERSIONS Disconnect the appliance from the mains supply b) Shift connecting plate on terminal according to prior to any conversions being carried out. the following chart. This chart is also affixed to the hob. c) Insert a supply cable of adequate section (see 7) CHANGING THE TYPE OF POWER chart par. 10) through core hitch on the terminal SUPPLY board. Although they leave our factory preset for single- d) Connect the phase and earth wires to the relative phase connection, certain appliances m
Resumen del contenido incluido en la página 9
SERVICING Always disconnect the appliance from the N.B. In case of substitution of the input cable, electricity main before proceeding with any the installer must keep the “earth” conductor servicing operation. longer than “live” ones, and must respect the cautions in paragraph “Electrical connection”. 8) REPLACING THE ELECTRICAL To reassemble the appliance repeat the inverse process. COMPONENTS For access to the various parts, remove the hotplate 9) TECHNICAL CHARACTERISTICS OF from the top of
Resumen del contenido incluido en la página 10
TECHNICAL DATA MODEL WITH 4 NORMAL PLATES VOLTAGE 110 V~ FREQUENCY 50/60 Hz TOT. RATING 5000 W 10
Resumen del contenido incluido en la página 11
TECHNICAL ASSISTANCE AND SPARE PARTS This appliance, before leaving the factory, has been carefully tested and regulated by expert and specialized personnel in order to guarantee the best performances. Any repairs or adjustments which may be subsequently required may only be carried out by qualified personnel with the utmost care and attention. For this reason, always contact your Dealer or your nearest After Sales Centre whenever repairs or adjustments are required, specifying the type of faul
Resumen del contenido incluido en la página 12
12
