Resumen del contenido incluido en la página 1
INSTALLATION
™
ExSite Series
Explosionproof
Power Module
IPSXM-2 and IPSXM-7
C313M-D (8/05)
Resumen del contenido incluido en la página 2
Resumen del contenido incluido en la página 3
Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Install the Power Module . . . . . . . . . .
Resumen del contenido incluido en la página 4
Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 6. To reduce the risk of ignition of hazardous atmospheres, disconnect the equipment from the supply circuit before opening. Keep assembly tightly closed when in operation. 7. The maximum ambient temperature range is -76°F to 140°F (-60°C to 60°C).
Resumen del contenido incluido en la página 5
Getting Started ™ Thank you for purchasing Pelco’s ExSite Series explosionproof integrated positioning system. This manual includes instructions for installing the power module for the ExSite Series system. For complete system installation instructions refer to the installation manual placed in the pan and tilt box. DANGER: Do not connect the power module to a supply circuit unless all ExSite system components (pan and tilt, camera module and power module) are installed. Once the co
Resumen del contenido incluido en la página 6
Install the Power Module Attach the power module to the mounting surface. Use only installation methods and materials capable of supporting four times the maximum specified load of the system (220 lb/100 kg). NOTE: If required, install the optional TXB translator, fiber module, or UTP board before installing the power module. Refer to the installation instructions supplied with the TXB translator, fiber module, or UTP board for installation instructions. To install the power module,
Resumen del contenido incluido en la página 7
Connect Wiring Refer to the following information to connect the wires and cables as required. WARNING: When installing this unit, provide access to the communication wires (TX- and TX+) to allow connection to the system for future software upgrades. Connectors must be installed so that the integrity of the hazardous location is maintained. ® These communication wires are required even if the system uses Coaxitron control. Maximum wire distance for RS-422 data wires is
Resumen del contenido incluido en la página 8
SW3 SW1 SW2 on on DIP Switch Settings Configure the receiver address, termination, and baud setting for the system. The DIP switches to configure these settings are located on the top of the power module. ® NOTE: No DIP switch settings are required for Coaxitron control. Figure 3 shows the default settings for the DIP switches. Refer to the following to configure the ExSite system settings. SW1-1 is set to the ON position. All other switches are set to the OFF position. ON F
Resumen del contenido incluido en la página 9
Tables Table A. P Protocol Receiver Address SWITCH SETTING SWITCH SETTING ADDRESS SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 ADDRESS SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 1 OFF OFF OFF OFF OFF OFF OFF OFF 17 OFF OFF OFF OFF ON OFF OFF OFF 2 ON OFF OFF OFF OFF OFF OFF OFF 18 ON OFF OFF OFF ON OFF OFF OFF 3 OFF ON OFF OFF OFF OFF OFF OFF 19 OFF ON OFF OFF ON OFF OFF OFF 4 ON ON OFF OFF OFF OFF OFF OFF 20 ON ON OFF OFF ON OFF OFF OFF 5 OFF OFF ON OFF OFF OFF OFF OFF 21 OFF OFF ON
Resumen del contenido incluido en la página 10
Table B. D Protocol Receiver Address (Continued) SWITCH SETTING SWITCH SETTING ADDRESS SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 ADDRESS SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 49 ON OFF OFF OFF ON ON OFF OFF 96 OFF OFF OFF OFF OFF ON ON OFF 50 OFF ON OFF OFF ON ON OFF OFF 97 ON OFF OFF OFF OFF ON ON OFF 51 ON ON OFF OFF ON ON OFF OFF 98 OFF ON OFF OFF OFF ON ON OFF 52 OFF OFF ON OFF ON ON OFF OFF 99 ON ON OFF OFF OFF ON ON OFF 53 ON OFF ON OFF ON ON OFF OFF 100 OFF OFF ON OFF O
Resumen del contenido incluido en la página 11
Table B. D Protocol Receiver Address (Continued) SWITCH SETTING SWITCH SETTING ADDRESS SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 ADDRESS SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 143 ON ON ON ON OFF OFF OFF ON 191 ON ON ON ON ON ON OFF ON 144 OFF OFF OFF OFF ON OFF OFF ON 192 OFF OFF OFF OFF OFF OFF ON ON 145 ON OFF OFF OFF ON OFF OFF ON 193 ON OFF OFF OFF OFF OFF ON ON 146 OFF ON OFF OFF ON OFF OFF ON 194 OFF ON OFF OFF OFF OFF ON ON 147 ON ON OFF OFF ON OFF OFF ON 195 ON ON OFF
Resumen del contenido incluido en la página 12
Table B. D Protocol Receiver Address (Continued) SWITCH SETTING SWITCH SETTING ADDRESS SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 ADDRESS SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 239 ON ON ON ON OFF ON ON ON 247 ON ON ON OFF ON ON ON ON 240 OFF OFF OFF OFF ON ON ON ON 248 OFF OFF OFF ON ON ON ON ON 241 ON OFF OFF OFF ON ON ON ON 249 ON OFF OFF ON ON ON ON ON 242 OFF ON OFF OFF ON ON ON ON 250 OFF ON OFF ON ON ON ON ON 243 ON ON OFF OFF ON ON ON ON 251 ON ON OFF ON ON ON ON ON 244
Resumen del contenido incluido en la página 13
Specifications ELECTRICAL Input Voltage 24 VAC or 100-240 VAC Input Voltage Range ±10% Power Consumption Maximum 60 watts (120 VA) per system Electrical Connections 6-foot wire harness with connections for power, video, data control, alarm inputs, and auxiliary outputs MECHANICAL Cable Entry One 0.75-inch (1.91 cm) NPT threaded opening Pan Movement 360° continuous pan rotation Vertical Tilt Unobstructed +90° to -90° Variable Pan/Tilt Speed Pan 0.1° to 40°/sec variable-speed operation Til
Resumen del contenido incluido en la página 14
14 C313M-D (8/05)
Resumen del contenido incluido en la página 15
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or workmanship for a period of one year after the date of shipment. (559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following information: Exceptions to this warranty are as noted below: 1. Model and serial numbe
Resumen del contenido incluido en la página 16
Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.com ISO9001 Canada United Kingdom The Netherlands Singapore Spain Scandinavia France Middle East United States | | | | | | | |
