Resumen del contenido incluido en la página 1
Service
This manual is to be used by qualified appliance
technicians only. Maytag does not assume any
responsibility for property damage or personal
injury for improper service procedures done by
an unqualified person.
This Base Manual covers general information
UpDraft Electric
Refer to individual Technical Sheet
for information on specific models
This manual includes, but is
Cooktops
not limited to the following:
AKT3040*
AKT3650*
CEC1430AA*
CEC1536AA*
JEC7430AA*
JEC8430AD*
JEC8536AD*
JEC8730A
Resumen del contenido incluido en la página 2
Important Information Important Notices for Servicers and Consumers Maytag will not be responsible for personal injury or property damage from improper service procedures. Pride and workmanship go into every product to provide our customers with quality products. It is possible, however, that during its lifetime a product may require service. Products should be serviced only by a qualified service technician who is familiar with the safety procedures required in the repair and who is equipped
Resumen del contenido incluido en la página 3
Table of Contents Important Information .................................................. 2 Disassembly Procedures Safety Information Disassembly Procedures for Models Listed Safety Procedures ................................................. 4 AKT3040F/E/S Safety Practices for Servicer .................................. 5 AKT3650F/E/S ................................................. 12 Before Installing ..................................................... 5 Main Top Removal .................
Resumen del contenido incluido en la página 4
Safety Information As with all appliances, there are certain rules to follow for safe operation. Verify everyone who operates the ! WA RNING cooktop is familiar with the operations and with these precautions. Surface Cooking Use appliance only for its intended purpose as 1. Use the proper pan size. Select utensils with flat described. Pay close attention to the safety sections of bottoms large enough to cover the element. this manual. Undersized utensils will expose the element to direct Recogni
Resumen del contenido incluido en la página 5
Safety Information Safety Practices for Servicer Electrical Requirements Safe and satisfactory operation of electric cooktops 220-volt, 60 Hertz, individual circuit which is properly depends upon its design and proper installation. grounded, polarized and protected by a circuit breaker However, there is one more area of safety to be or fuse. considered: The neutral of this unit is grounded to the frame through the solid copper grounding wire. If local conditions do not permit grounding of the ne
Resumen del contenido incluido en la página 6
General Information This manual provides basic instructions and suggestions Model Identification Rating Label and for handling, installing and servicing electric cooktops. Ordering Replacement Parts The directions, information, and warnings in this manual Model numbers are recorded on the rating label. Rating are developed from experience with, and careful testing label is located on the bottom of the burner box. Before of the product. If the unit is installed according to this ordering parts,
Resumen del contenido incluido en la página 7
General Information Model Identification Parts and Accessories Complete registration card and promptly return. If Purchase replacement parts and accessories over the registration card is missing: phone. To order accessories for your product call: • For Amana product call 1-800-843-0304 or visit the For Amana product call 1-877-232-6771 or visit the Web Site at www.amana.com Web Site at www.amana.com For Maytag product call 1-800-688-9900 or visit the For Maytag/Jenn-Air product call 1-800-
Resumen del contenido incluido en la página 8
Troubleshooting Procedures ! WARNING To avoid risk of electrical shock, personal injury or death, disconnect power to cooktop before servicing, unless testing requires power. Problems Solutions Switch burns out immediately after Improper wiring installation Hot Wired to Neutral terminal. installation. Warranty is VOID.(SEE Installation Instructions.) NOTE: Possible damage to glass. Element fails to heat; indicator light 1. Element is burned out. glows. 2. Failed limit switch. 3. Failed infinite
Resumen del contenido incluido en la página 9
Component Testing Procedures WAR NING ! To avoid electrical shock, personal injury, or death: disconnect power supply before servicing, unless testing requires it. 3. Turn control to LOW setting and allow it to cycle Power Supply approximately two minutes. Time the OFF and ON If no part of the cooktop operates or only part of it cycle of the control and compare to the following operates, the cause may be a problem in the power table based on a 60 second cycle. supply. 1. Verify supply circuit br
Resumen del contenido incluido en la página 10
Component Testing Procedures WAR NING ! To avoid electrical shock, personal injury, or death: disconnect power supply before servicing, unless testing requires it. Dial Position SETTING APPROXIMATE SECONDS Contacts OFF LO-MED HI TIME ON OFF L1 – L2 O E X L1 – P O X X LOW 3 20 L1 – H1 O X X MED 5 7 L1 – H2 O X – C X HIGH Constant 0 H1–H2 X E X 4. Replace the control if it is not cycling properly. O−Open X−Closed C−Cycles Calibration is not possible. E−Indicates resistance across internal The surf
Resumen del contenido incluido en la página 11
Component Testing Procedures WAR NING ! To avoid electrical shock, personal injury, or death: disconnect power supply before servicing, unless testing requires it. Ribbon Elements−Power Disconnected N 4 5 TOP Small Element Continuity Test 1. Disconnect power from cooktop. Connect ohmmeter 16 leads to element terminals. 2. Meter should indicate continuity. 2 3 Large Element Continuity Test 1. Disconnect power from cooktop. Connect ohmmeter leads to element terminals. 3. Remove wiring from switch.
Resumen del contenido incluido en la página 12
Disassembly Procedures ! WARNING To avoid risk of electrical shock, personal injury or death, disconnect power to cooktop before servicing, unless testing requires power. Disassembly Procedures for Models Listed Disassembly Procedures for Models Listed • AKT3040F/E/S CEC1536AAB/W/Q/C AKT3650F/E/S CEC1430AAB/W/Q/C JEC7430AAB/W Main Top Removal MEC4430BDB/W/Q 1. Disconnect power to cooktop. 2. Remove cooktop from cutout and place on a Main Top Removal protected surface. 1. Disconnect pow
Resumen del contenido incluido en la página 13
Disassembly Procedures ! WARNING To avoid risk of electrical shock, personal injury or death, disconnect power to cooktop before servicing, unless testing requires power. 5. Disconnect and label wiring to infinite switch. Disassembly Procedures for Models Listed JEC8430ADB/W/F/N/S 6. Replace infinite switch and reverse procedure to reinstall. JEC8536ADB/W/F/N/S MEC5430BDB/W/S Indicator Light Replacement MEC5536BAB/W/S 1. Remove main top, see "Main Top Removal" Main Top Removal procedure.
Resumen del contenido incluido en la página 14
Disassembly Procedures ! WARNING To avoid risk of electrical shock, personal injury or death, disconnect power to cooktop before servicing, unless testing requires power. Sensor Replacement Hi–Limit Switch Replacement 1. Remove main top, see "Main Top Removal" 1. Remove main top, see "Main Top Removal" procedure. procedure. 2. Remove screws securing element clips to main top. 2. Remove screws securing hi-limit switch to the mounting plate and remove hi-limit switch. 3. Lower element and remove s
Resumen del contenido incluido en la página 15
Appendix A ©2003 Maytag Appliances Company 16022159 Rev. 0 A–1
Resumen del contenido incluido en la página 16
Installation Instructions Installing Cabinetry Over Your Cooktop Electrical Wiring Information A = 30" (76.2 cm) minimum clearance between the top of The neutral of this unit is grounded to the frame through the cooktop and the bottom of an unprotected wood or the solid copper grounding wire. If used on new branch- metal cabinet. circuit installations (1996 NEC), mobile homes, recreational vehicles, or in an area where local codes A = 24" (60.96 cm) minimum when bottom of wood or prohibit ground
Resumen del contenido incluido en la página 17
Installation Instructions Junction Box Connection Notice To Installer Junction box is not supplied with cooktop. Junction box Follow accompanying instruction carefully. must be U.L. or C.S.A. listed and meet NEC and Mobile Home Manufactures Association Standards. ! CAUTION • Three-wire conductor junction box allowed for residental Never use a metal blade to pry knob off. If knob cannot usage in United States. be easily removed, tuck folds of a dish- towel under knob skirt and pull upward with st
Resumen del contenido incluido en la página 18
Installation Instructions This is the first page of the Installation Instruction (see part number listed in the bottom right corner for complete set of instructions. A–4 16022159 Rev. 0 ©2003 Maytag Appliances Company
Resumen del contenido incluido en la página 19
Installation Instructions This is the first page of the Installation Instruction (see part number listed in the bottom right corner for complete set of instructions. ©2003 Maytag Appliances Company 16022159 Rev. 0 A–5
Resumen del contenido incluido en la página 20
Installation Instructions This is the first page of the Installation Instruction (see part number listed in the bottom right corner for complete set of instructions. A–6 16022159 Rev. 0 ©2003 Maytag Appliances Company
