Manual de instrucciones de Canon FAXPHONE L80

Resumen del contenido incluido en la página 1

S Set-Up Instruc et-Up Instructions tions
Thank you for purchasing the Canon FAXPHONE L80.
To get your machine ready for use, please follow the instructions in this document before
referring to any other documentation.
Unpack the machine and its components.
Check that you have the following:
● ● ●
Machine FX-3 S Cartridge Support trays (2)
● ● ●
Multi-purpose Multi-purpose tray Document support
tray cover
●
Paper loading warning label
●
Power cord
●
Telephone line cord
●
Documentation
Set-Up In

Resumen del contenido incluido en la página 2

Remove the shipping materials from the machine. 1 Place the machine on a flat surface. 2 Remove all shipping tapes from the exterior of the machine. 3 Gently open the operation panel ➊ (it only opens partially) and remove the protective sheet ➋ from the ADF. 4 Close the operation panel by pressing at the center until it locks into place. NOTE •Do not remove the USB label on the back of the machine at this stage. USB label Assemble the machine. 1 Attach the paper 2 Insert the multi-purpose tray

Resumen del contenido incluido en la página 3

Load paper. 1 Insert a stack of paper into the multi-purpose tray ➊ (print side facing you and top edge first), then adjust the paper width guides to the width of the paper ➋. 2 Attach the multi-purpose tray cover to prevent dust accumulating inside the machine. Multi-purpose tray cover Paper width guide Attach the handset cradle to the machine. 1 Insert the plugs with pins into the holes on the handset cradle. NOTE Plug with pin •Do not push the pins all the way into the plugs at this stag

Resumen del contenido incluido en la página 4

Connect the handset and telephone line cord. Connect external devices as follows: = Telephone line jack = External device jack = Handset jack • Telephone or answering machine Telephone or answering machine Telephone Machine line Telephone line cord • Telephone and answering machine Connect the supplied LINE TEL Telephone cord to the L jack. Answering Then connect the other end to the Telephone machine Machine line telephone line jack on your wall. • Built-in computer modem and telephone Exte

Resumen del contenido incluido en la página 5

Install the FX-3 S Cartridge. 1 Lift the latch and open the front cover. 2 Remove the FX-3 S Cartridge from its protective bag. 3 Gently rock the cartridge from side to side a few times to distribute the toner evenly inside it. •Print quality may be poor if the toner is unequally distributed. NOTE •Do not open the drum protective shutter on the cartridge. 4 Place and hold the cartridge on a flat, clean surface, then gently pull the plastic tab straight out to remove the plastic seal. SIDE VIEW N

Resumen del contenido incluido en la página 6

Set the fax receive mode. 1 Press Function ➊. Clear Set 01 02 03 04  2 Press Receive Mode ➋. 05 06 07 08 Data Data Delayed Delayed Memory Memory Receive Receive 3 Press or ➌ until the mode you Registration Registration Transmission Transmission Reference Reference Mode Mode  Start/Copy 09 10 11 12 want appears in the LCD: Hook Stop/Reset Polling Polling Report Report Space Space Function 13 14 15 ex.
You can select from the following: Fax/Tel Mode: When the handset or the extension telephone

Resumen del contenido incluido en la página 7

Install the Printer Driver. (Windows 98/Me/2000/XP) IMPORTANT • DO NOT connect the USB cable before installing the software. NOTE •When installing the software in Windows XP or Windows 2000, log onto the system as a member of the Administrator group. •If the Found New Hardware Wizard appears, click Cancel, and follow this procedure. 1 Insert the CD-ROM into your CD-ROM drive. 2 If AutoRun is enabled, the installation starts automatically. NOTE •If installation does not start automatically, choos

Resumen del contenido incluido en la página 8

6 When the system displays messages indicating that the driver for your printer is being installed, proceed as follows: For Windows 98/Me: Wait for the system to complete the installation of the printer driver. For Windows 2000: When the Found New Hardware Wizard appears during the setup, choose the following: • Search for a suitable driver for the printer. (Do not display a list of drivers.) • Search only on the installation disk. (Click CD-ROM drives only, and clear the other options.) For Win