Resumen del contenido incluido en la página 1
HCG601 / HCG611 / HCG621
Manual for Installation, Use and Maintenance
Passionate about style
Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.eu
Resumen del contenido incluido en la página 2
Important The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CDA reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance or use in a commercial environment. This appliance is not designed to be used by people (including children) with reduced physical, sensorial or mental capacity, or who lack experience or knowledge about it,
Resumen del contenido incluido en la página 3
Using your hob 3 2 4 5 Fig.1 HCG601 6 7 8 9 2 3 4 1 HCG611 / HCG621 6 7 8 9 Gas burners: Gas burners: 1. HCG611 triple ring/wok burner 3.5kW Gas flow to the burners is controlled by the control knobs (6, 7, 8 HCG621 triple ring/wok burner 3.6kW and 9 on the diagram above). There are 3 positions shown on the 2. Left semi-rapid burner 1.75kW control panel. Turning the control knob to the positions shown 3. Right semi-rapid burner 1.75kW below achieves the fol
Resumen del contenido incluido en la página 4
Igniting the Burners To ignite the burners, follow these instructions: 1. Lightly press the control knob (shown on the right) and turn the knob anti- clockwise to the maximum position. Press and hold the control down to begin the ignition process (a clicking sound will be heard). 2. Once the burner is lit, adjust the burner power to the required position. To turn the burner off, turn the knob clockwise past the maximum setting to the off position. Some models are fitted with a flame-f
Resumen del contenido incluido en la página 5
Correct use of the optional Wok Pan Adaptor The wok pan adaptor is a special stand that is designed to be fitted over the Triple Ring burner to give support to round bottomed woks. When using a wok, always place the wok pan adaptor in position over the pan support on the Triple Ring burner as shown in Fig.5. Fig.4 Fig.5 IMPORTANT: • The wok pan adaptor (Fig.5) must be placed over the pan support on the Triple Ring burner. • Do not use the wok pan adaptor for standard flat bottomed pans.
Resumen del contenido incluido en la página 6
Care and Maintenance As the hob has a stainless steel or enamel surface, you should use a nonabrasive cleaner. Any abrasive cleaner (including Cif) will scratch the surface and could erase the control panel markings. Stainless steel can be effectively cleaned by simply using a dilute solution of water and mild detergent and drying to a shine with a clean cloth. Over time with use, the stainless steel surface may discolour; this is normal and does not constitute a fault with this ap- pliance. P
Resumen del contenido incluido en la página 7
Mains Electricity Connection THIS APPLIANCE MUST BE CONNECTED TO THE MAINS SUPPLY BY A COMPETENT PERSON, USING FIXED WIRING VIA A DOUBLE POLE SWITCHED FUSE SPUR OUTLET AND PROTECTED BY A 3A FUSE. We recommend that the appliance is connected by a qualified electrician, who is a member of the N.I.C.E.I.C. and who will comply with the I.E.E. and local regulations. The wires in the mains lead of this appliance are coloured in accordance with the following code: Green & Yellow = Earth, Blue = Neutr
Resumen del contenido incluido en la página 8
Gas Supply Requirements IMPORTANT: THIS APPLIANCE SHOULD BE FITTED BY A GAS SAFE REGISTERED FITTER OR OTHER SUITABLY QUALIFIED PERSON. • This installation must comply with the Gas Safety (installation and use) Regulations 1984. • This appliance is category II2H3+ and is designed for use in the UK and Ireland. The installation must comply with the Gas Safety (installation and use) Regulations 1984. • The CDA Group Ltd is not legally able to provide any assistance in the installation of gas a
Resumen del contenido incluido en la página 9
Natural Gas to LPG Conversion This hob can be converted from natural gas to propane operation at a nominal inlet pressure of 37mbar, or butane operation at a nominal inlet pressure of 28/30mbar. This conversion must only be carried out by a competent person (i.e. a Gas Safe registered fitter). Required: Instructions to fit replacement injectors: • 7mm AF nut spinner 1. Disconnect the appliance from the gas and electrical supplies. • Replacement injectors 2. Remove burner components and
Resumen del contenido incluido en la página 10
Fitting the Hob Unpacking the hob: Take care not to lose or mishandle any parts. Fitting position of the hob: This appliance must be installed a minimum of 50mm from any back wall and a minimum of 185mm away from any adjacent vertical surfaces, e.g. a tall cupboard end panel. This may be reduced to 100mm if the adjacent surface is resistant to fire (tiles or steel, for example). These dimensions are shown in Fig.6. If fitting a cooker hood above the hob: If a cooker hood is to be installed abo
Resumen del contenido incluido en la página 11
How to install the hob: Overall dimensions of the hob: Width: 585mm Depth: 500mm Worktop cut-out dimensions: Width: 550mm Depth: 470mm 1. Make the required hole in the worktop. Before doing this, you must check the instructions supplied with any cooker hood to ensure that you will have the required clearance. The cut-out (Fig.7) shows a 65mm gap from the wall to the cut-out edge. The distance from the hob, when fitted, to the back wall is 50mm. If a splashback/worktop upstand is to be
Resumen del contenido incluido en la página 12
To contact our Customer Care Department, or for Service, please contact us on the details below. Passionate about style Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.eu
