Resumen del contenido incluido en la página 1
HGC20 & HGC20D
GAS CONVECTION OVENS
MODELS
HGC20 ML-114573
HGC20D ML-114575
701 S. RIDGE AVENUE
TROY, OHIO 45374-0001
937 332-3000
www.hobartcorp.com FORM 33580 Rev. E (Mar. 2005)
Resumen del contenido incluido en la página 2
IMPORTANT FOR YOUR SAFETY THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL GAS EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START-UP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL. POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE EVENT THE SMELL OF GAS IS DETECTED. THIS INFORMATION CAN BE OBTAINED FROM THE LOCAL GAS SUPPLIER. IMPORTANT IN THE EVENT A GAS ODOR IS DETECTED, SHUT DOWN UNITS AT MAIN SHUTOFF VALVE AND CONTACT THE LOCAL GAS COMPANY OR GAS
Resumen del contenido incluido en la página 3
Installation, Operation, and Care of HGC20 AND HGC20D GAS CONVECTION OVENS SAVE THESE INSTRUCTIONS FOR FUTURE USE GENERAL The HGC20 Gas Convection Oven is a single cavity oven and features a solid state thermostat, 1-hour dial timer, and five racks as standard equipment. Additional oven racks are optional. Each oven 1 is equipped with a 25,000 BTU/hr burner and a /2 HP (0.37 kw) electric motor. The oven comes standard with porcelain interior; stainless steel exterior. Model HGC20D is similia
Resumen del contenido incluido en la página 4
INSTALLATION CODES AND STANDARDS Hobart ovens must be installed in accordance with: In the United States of America: 1. State and local codes. 2. National Fuel Gas Code, ANSI-Z223.1 (latest edition). Copies may be obtained from The American Gas Association, Inc., 1515 Wilson Blvd., Arlington, VA 22209. 3. National Electrical Code, ANSI/NFPA-70 (latest edition). Copies may be obtained from The National Fire Protection Association, Batterymarch Park, Quincy, MA 02269. In Canada: 1. Local codes. 2.
Resumen del contenido incluido en la página 5
Assembling the Chimney to the Single Oven CHIMNEY Remove the chimney from inside the oven cavity and use the screws provided to fasten the chimney to the top rear of the oven (Fig. 2). The flanges on the chimney are to be positioned over the top cover. ASSEMBLING THE OVEN TO THE STAND Position the oven on its back, taking care not to scratch or damage it. The gas pipe connection protrudes beyond the back; provide for PL-52240 this when the oven is tipped back by resting it on suitable spacers (2
Resumen del contenido incluido en la página 6
LEVELING Once the oven is in its permanent position, place a carpenter's level on the oven rack. If the oven is installed on legs, turn the adjustable feet in or out to level oven front-to-back and side-to-side. If the oven is installed on casters, loosen set screws and turn casters in or out to level oven front-to-back and side-to-side. Retighten set screws after leveling. ELECTRICAL CONNECTIONS WARNING: ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTIONS OF THE NATI
Resumen del contenido incluido en la página 7
GAS CONNECTION GAS DATA INPUT / BTU/HR MANIFOLD PRESSURE MODEL Natural Propane Natural Propane HGC20, HGC20D 25,000 25,000 3.5" w.c. (0.8 kPa) 10" w.c. (2.5 kPa) For all gas supply connections, pipe joint compound must be resistant to the action of propane gases. The oven is provided with a regulator integral to the gas solenoid valve, and requires no regulator external to the device. A gas shutoff valve is supplied with each oven and is located at the bottom of the control panel. No tools are
Resumen del contenido incluido en la página 8
F P POWER ON OFF COOL DOWN ON HEAT ON OFF GAS VALVE IGNITION COOK TEMPERATURE COOK TIME TO LIGHT OVEN PLACE ON/OFF/COOL DOWN SWITCH IN "ON" POSITION. ADFGAPDF;LJK;LJ;LKJ TO SHUT-OFF OVEN PLACE ON/OFF/COOL DOWN SWITCH IN "OFF" POSITION. TO LIGHT OVEN PLACE ON/OFF/COOL DOWN SWITCH IN "ON" POSITION. ADFGAPDF;LJK;LJ;LKJ 500 150 475 225 450 250 425 300 400 350 300 0 5 60 10 55 15 50 20 45 40 25 35 30 M FLUE CONNECTION Ventilation requirements will vary with each installation and must comply with Va
Resumen del contenido incluido en la página 9
LIGHTING THE HGC20 OVEN Open the manual valve. Turn the ON / OFF / COOL DOWN switch ON and turn the thermostat to its maximum setting. Both the ON and HEAT lights should be lit. If the HEAT light is not on, make sure the door is closed. After 5 seconds, the spark ignition system will initiate and the solenoid valve will open, allowing gas flow to the burner for a period of 7 seconds. This 5 second purge and 7 second ignition trial will repeat itself up to two more times if the burner does not li
Resumen del contenido incluido en la página 10
COOL ON ON OFF GAS VALVE TEMPERATURE OFF DOWN da;la;lasjfd;a LIGHTING INSTRUCTIONS ads;fjj;flPUSH MASTER SWITCH TO "ON" POSTION. IF OVEN FAILS TO LIGHT. PUSH sdifja;lldfjlfdal; ds;fjalkdfja;sjdf;lfsdj;a;l asdhflkajseflasdkjhflasklasj shdjflkajh STOP TIME HEAT COOK HOLD START COOK PULSE READY POWER CONTROLS — MODEL HGC20D Built before October 1999 (Fig. 6) HEAT LIGHT THERMOSTAT TEMPERATURE KNOB READY LIGHT COOK BUTTON HOLD BUTTON THERMOMETER BUTTON TIMER TIMER KNOB COOK BUTTON START/STOP BUTTON
Resumen del contenido incluido en la página 11
Cook Button Light (If On and not timing product). Indicates the cook mode is selected. This means: • The displayed temperature settings will be for the cook temperature except for the time that the light in the Thermometer Button is lit. • Rotating the Thermostat Knob will change the cook set temperature. • Cook time can be adjusted using the Timer Knob. • The time displayed is the initial set cook time. • It is possible to select the Hold mode using the Hold Button. Cook Button Light (If On and
Resumen del contenido incluido en la página 12
Pulse Button Selects the pulse time setting. A cook time must be set first. The pulse time can then be set equal to or less than the cook time. The pulse time will be the portion of cook time to operate in the pulse mode. Pulse mode will start first. When pulse time elapses, the remainder of the cook time will be in the non- pulse mode. Use when cooking delicate product, such as strudel, muffins, cupcakes, meringue pies, etc., to keep product from forming waves on the top. Use the Pulse Button t
Resumen del contenido incluido en la página 13
BEFORE FIRST USE Before using the oven for the first time, it must be "burned in" to release any odors that might result from heating the new surfaces in the chamber. 1. Using a clean damp cloth, wipe the inside of the oven, including the racks. 2. Close the oven door, push the ON / OFF / COOL DOWN switch ON, turn the thermostat to 300°F (149°C) and allow the oven to cycle for 6 to 8 hours before turning the ON / OFF / COOL DOWN switch OFF. USING THE HGC20D OVEN Preheating 1. Push ON / OFF / COO
Resumen del contenido incluido en la página 14
CONTROLS — MODEL HGC20D Built after October 1999 Always displays [HR:Min] when setting the Time. Displays [HR:Min] if the countdown Time is more than 1 Hour. Displays [Min: Sec] if the countdown Time is less than 1 Hour. Displays Temperature in °F. OVEN OVEN C & H MODE READY HEATING MENU SELECT C & H Indicates the oven is in the Cook and Hold Mode. PRIMARY MODE SECONDARY OVEN Indicates the oven is preheated and ready for cooking. 1 READY SET 2 OVEN Indicates the oven is preheating. HEATING 1 3 2
Resumen del contenido incluido en la página 15
MANUALLY SETTING THE TEMPERATURE AND COOK TIME To Set the Temperature • Press the SET button. Press the TEMPERATURE button; StPt displays to indicate Setpoint. • Use the Up and Down Arrow keys to increase or decrease the displayed Temperature value. • Press the SET button again to save the Temperature setpoint in the computer. To Set the Cook Time • Press the SET button. Press the TIME button. Tine displays to indicate TIME. • Use the Up and Down Arrow keys to increase or decrease the display
Resumen del contenido incluido en la página 16
Always Set the Temperature Before Setting the Time • Press the SET button. Press the TEMPERATURE button; StPt displays. Use the Up and Down Arrow keys to increase or decrease the Temperature. To save, press the SET button again. At startup, the display will initially show a GROWING BAR. When the oven temperature reaches the Set Point, the set temperature displays. The READY light is lit, the HEAT light goes out, and the oven is ready for you to select the Cook Time, Menu Item Cook Time, or Me
Resumen del contenido incluido en la página 17
COOK AND HOLD OPERATION — HGC20D OVEN Cook and Hold cooks the product in two stages. During First Stage Cooking, the oven temperature is regulated by the Cook thermostat for the amount of time set on the Cook Timer. After the lapsed time counts down to 00:00, Second Stage Cooking begins. During Second Stage Cooking, the burners are off as the temperature in the oven declines to the Hold Temperature. The doors should remain closed during Second Stage Cooking. When the Hold temperature is reached,
Resumen del contenido incluido en la página 18
The convection oven is a bit faster than conventional deck-type ovens; temperature settings are lower and cook times are shorter. Since recipes and foods are subject to many variations and tastes, the guidelines regarding times and temperatures in this manual are SUGGESTIONS ONLY. Experiment with your food products to determine the cooking temperatures and times that give you the best results. CLEANING WARNING: DISCONNECT THE ELECTRICAL POWER TO THE MACHINE AND FOLLOW LOCKOUT / TAGOUT PROCEDURE
Resumen del contenido incluido en la página 19
MEAT & FISH PRODUCTS Product Temp. Time (min.) No. Shelves °F (°C) 3 Prime Rib (20 lb. rare) (9.1 kg) 250 (121) 2 ¦4 Hr. 2 1 Rolled Roast Beef 275 (135) 2 ¦2 Hr. 2 1 Veal Roast Boned (15 lb.) (6.8 kg) 275 (135) 2 ¦2 Hr. 2 Stuffed Pork Chops 300 (149) 25 – 30 3 Lamb Chops 375 (190) 12 5 3 Steamship Round (80 lb.) (36.3 kg) 275 (135) 2 ¦4 Hr. 1 Meatloaf 325 (163) 40 3 Hamburger Patties (4 oz.) (113 gr.) 400 (204) 8-10 5 Meat Pot Pies 350 (177) 40 5 Chicken Parts 300 – 325 (149 – 163) 30 – 40 5 Fis
Resumen del contenido incluido en la página 20
MAINTENANCE WARNING: THE OVEN AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING, CLEANING, OR PERFORMING ANY MAINTENANCE. WARNING: DISCONNECT THE ELECTRICAL POWER TO THE MACHINE AND FOLLOW LOCKOUT / TAGOUT PROCEDURES. LUBRICATION The fan motor comes with sealed bearings and requires no lubrication. The door hinges and mechanism require occasional lubrication with mineral oil. DISCONNECTING GAS LINE RESTRAINT If this oven is placed on casters, it should be connected to the supply piping with the p
