Resumen del contenido incluido en la página 1
LD Monitor User Manual
2352Phz
www.aoc.com
©2011 AOC.All Rights Reserved.
Resumen del contenido incluido en la página 2
Safety ........................................................................................................................................................................ 3 National Conventions ......................................................................................................................................... 3 Power .......................................................................................................................................................
Resumen del contenido incluido en la página 3
Safety National Conventions The following subsections describe notational conventions used in this document. Notes, Cautions, and Warnings Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. These blocks are notes, cautions, and warnings, and they are used as follows: NOTE: A NOTE indicates important information that helps you make better use of your computer system. CAUTION: A CAUTION indicates either potential dam
Resumen del contenido incluido en la página 4
Power The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company. The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will fit only into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug, have an electrician install the correct outlet, or use an
Resumen del contenido incluido en la página 5
Installation Do not place the monitor on an unstable cart, stand, tripod, bracket, or table. If the monitor falls, it can injure a person and cause serious damage to this product. Use only a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with this product. Follow the manufacturer’s instructions when installing the product and use mounting accessories recommended by the manufacturer. A product and cart combination should be moved with care. Never push a
Resumen del contenido incluido en la página 6
Cleaning Clean the cabinet regularly with cloth. You can use soft-detergent to wipe out the stain, instead of strong-detergent which will cauterize the product cabinet. When cleaning, make sure no detergent is leaked into the product. The cleaning cloth should not be too rough as it will scratch the screen surface. Please disconnect the power cord before cleaning the product. 6
Resumen del contenido incluido en la página 7
Other If the product is emitting a strange smell, sound or smoke, disconnect the power plug IMMEDIATELY and contact a Service Center. Make sure that the ventilating openings are not blocked by a table or curtain. Do not engage the LCD monitor in severe vibration or high impact conditions during operation. Do not knock or drop the monitor during operation or transportation. 7
Resumen del contenido incluido en la página 8
Setup Contents in Box Monitor Base Stand CD Manual QSG * * * * * Power Cable Analog Cable DVI Cable HDMI Cable Audio Cable 3D Glasses Not all signal cables (Analog, DVI, and HDMI cables) will be provided for all countries and regions. Please check with the local dealer or AOC branch office for confirmation. 8
Resumen del contenido incluido en la página 9
Setup Stand & Base Please setup or remove the base following the steps as below. Setup: Remove: 9
Resumen del contenido incluido en la página 10
Adjusting Viewing Angle For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's angle to your own preference. Hold the stand so you will not topple the monitor when you change the monitor's angle. You are able to adjust the monitor's angle from -3° to 19 °. NOTE: Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen. 10
Resumen del contenido incluido en la página 11
Connecting the Monitor Cable Connections In Back of Monitor and Computer: 1 2 3 4 5 1. Power 2. HDMI cable 3. DVI cable 4 . D-Sub cable 5 . Audio cable /Earphone To protect equipment, always turn off the PC and LCD monitor before connecting. 1 Connect the power cable to the AC port on the back of the monitor. 2 Connect one end of the 15-pin DVI /D-Sub/HDMI cable to the back of the monitor and connect the other end to the computer's DVI /D-Sub/HDMI port.
Resumen del contenido incluido en la página 12
Wall Mounting Preparing to Install An Optional Wall Mounting Arm. This monitor can be attached to a wall mounting arm you purchase separately. Disconnect power before this procedure. Follow these steps: 1 Remove the base. 2 Follow the manufacturer's instructions to assemble the wall mounting arm. 3 Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the holes in the back of the monitor. 4 Insert the 4 screws into the holes and tighten.
Resumen del contenido incluido en la página 13
Adjusting Setting Optimal Resolution Windows Vista For Windows Vista: 1 Click START. 2 Click CONTROL PANEL. 3 Click Appearance and Personalization. 4 Click Personalization 13
Resumen del contenido incluido en la página 14
5 Click Display Settings. 6 Set the resolution SLIDE-BAR to 1920 by 1080. 14
Resumen del contenido incluido en la página 15
Windows XP For Windows XP: 1 Click START. 2 Click SETTINGS. 3 Click CONTROL PANEL. 4 Click Appearance and Themes. 5 Double click DISPLAY. 15
Resumen del contenido incluido en la página 16
6 Click SETTINGS. 7 Set the resolution SLIDE-BAR to 1920 by 1080. Windows ME/2000 For Windows ME/2000: 1 Click START. 2 Click SETTINGS. 3 Click CONTROL PANEL. 4 Double click DISPLAY. 5 Click SETTINGS. 6 Set the resolution SLIDE-BAR to 1920 by 1080. 16
Resumen del contenido incluido en la página 17
Hotkeys 1 3D/- 2 Volume/+ 3 Source/Auto/Exit 4 Menu/Enter 5 Power Power Press the Power button to turn on/off the monitor. / - Press this hotkey continuously to select 2D/3D functions when the on-screen display (OSD) is unavailable. /+ When there is no OSD, press Volume adjust volume. Auto / Exit / Source hot key When there is no OSD, press Auto/Source button continuously about 2 second to do auto configure. When the OSD is closed, press Source button will be
Resumen del contenido incluido en la página 18
OSD Setting Basic and simple instruction on the control keys. 1) Press the MENU-button to activate the OSD window. 2) Press - or + to navigate through the functions. Once the desired function is highlighted, press the MENU-button to activate it . press - or + to navigate through the sub-menu functions. Once the desired function is highlighted, press MENU-button to activate it. 3) Press - or + to change the settings of the selected function. Press AUTO to exit. If you want to
Resumen del contenido incluido en la página 19
Luminance 1. Press MENU (Menu) to display menu. 2. Press - or + to select (Luminance), and press MENU to enter. 3. Press - or + to select submenu, and press MENU to enter. 19
Resumen del contenido incluido en la página 20
4. Press - or + to adjust. 5. Press AUTO to exit. Brightness 0-100 Backlight Adjustment Contrast 0-100 Contrast from Digital-register. Standard Standard Mode Text Text Mode Internet Internet Mode Eco mode Game Game Mode Movie Movie Mode Sports Sports Mode Gamma1 Adjust to Gamma1 Gamma Gamma2 Adjust to Gamma 2 Gamma3 Adjust to Gamma 3 Off Disable dynamic contrast ratio DCR On Enable dynamic contrast ratio 20
