Manual de instrucciones de Philips Cineos HDTV Monitor with Pixel Plus

Resumen del contenido incluido en la página 1

™
H HD DTV M TV Monitor onitor
with Pixel Plus™ ™
with Pixel Plus
44PL9774
55PL9774
Highlights
• Liquid-crystal-on-silicon (LCOS) High-definition
Imaging
•High-resolution Display—1280 x 720 pixels
• Pixel Plus™
Features
•Digital Natural Motion™
•Digital Crystal Clear™
•Active Control™—analyzes and adjusts incoming signal
• Two-tuner,Double-window PIP (Picture-in-Picture)
•Dolby® Virtual Surround, 40-watt RMS
•3D Y/C Comb Filter
DV
•HD Component and I Input
•Center Channel Audio Input
• Side AV

Resumen del contenido incluido en la página 2

Positioning the TV Before connecting accessory devices—VCR, DVD player, or HD Situate the TV where it will not receiver, for example—please keep the following in mind: be exposed to heat or moisture. • Place the TV on a flat surface. An unlevel surface may adversely affect picture performance. For safety, do not set • Do not place the TV on shag carpet or any surface that will objects on top of the TV. block the air inlets at the bottom of the set. Blockage will cause the TV to overheat and shut

Resumen del contenido incluido en la página 3

Mounting the Swivel and TV to the Stand Install the plastic position pins in the stand. 1 Place the TV and mounted swivel on the stand, aligning the 1 2 front and sides of the TV with the front and sides of the 2 Positioning stand. This will help properly seat the TV on the position- ing pins and align the pre-drilled holes on the stand and Pins swivel. You do not need the rubber bumpers and long screws if you have already attached the swivel to the TV. Use the supplied screws (2) and screw key

Resumen del contenido incluido en la página 4

Making Basic Connections to the TV Cable Box with RF IN/OUT Back of TV Connect the incoming cable TV signal to the CABLE IN jack on the back of the cable box. Incoming 1 Cable TV Connect a coaxial cable (not supplied) to the TO TV jack Signal on the back of the cable box and to the TUNER jack on the DVI 2 G S-VIDEO back of the TV. RL V Set the Output Channel switch on the back of the cable box to CH 3 or 4 (whichever is correct for your cable box), 3 then tune the TV to the corresponding channe

Resumen del contenido incluido en la página 5

Making Basic Connections to the TV Antenna Back of TV Connect the incoming antenna signal to the TUNER jack on the back of the TV. See page 8 for details on using Autoprogram to store channels in the TV’s memory. NOTE: This connection will supply stereo sound to the TV if it is being broadcast by the station you are watching. DVI G S-VIDEO RL V DVI Pr Pb Y G S-VIDEO RL V Pr Pb Y RL V RL V RL RL RL RL V G S-VIDEO RGB+HV Incoming RL Pr Pb Y ST HD INPUTS ANDARD/ TUNER Pr Pb Y ST HD INPUTS ANDARD/

Resumen del contenido incluido en la página 6

Using the Remote Control Installing the Batteries To load the supplied batteries into the remote: 3 HELPFUL HINT Remove the battery compartment door on the back of When the batteries in your remote the remote. 1 control run low, the remote control Remote Control Place the batteries (2-AA) in the remote. Make sure the (+) (shown from the bottom) will send a “Battery low” command to the TV. The TV will then display and (–) ends of the batteries line up correctly (the inside of 2 a message on th

Resumen del contenido incluido en la página 7

Using the On-screen Menu The TV’s on-screen menu controls are viewed within a The first time you turn on the TV after purchasing it, it will be in a special mode designed to mobile map or pipe system. This system allows you to inform you that you can change the menu language and on-screen displays to English, French, or move along linked paths tied to specific Feature Title cate- Spanish. Also included in this mode is Autoprogram to encourage you to have the set program gories (“TV,” “Picture,”

Resumen del contenido incluido en la página 8

Using the Installation Features Language When you plug in your TV for the first time it will prompt Language Autoprogram Language Autoprogram you to set the Language and Autoprogam the channels. Press the cursor down to select OK Select your menu language with English English For Spanish- and French-speaking TV owners, an on-screen INFO your menu language the cursor up/down. SELECT PIXEL PLUS Français Français Press the OK key on the remote Language option is present. The Language control enab