Manual de instrucciones de Omega Speaker Systems DPS3301

Manual de instrucciones del aparato Omega Speaker Systems DPS3301

Aparato: Omega Speaker Systems DPS3301
Categoría: Pantalla
Fabricante: Omega Speaker Systems
Tamaño: 1.91 MB
Fecha de añadido: 8/22/2013
Número de páginas: 26
Imprimir el manual

Descargar

¿Cómo se utiliza?

Nuestro propósito es proporcionarte el acceso más rápido posible a los contenidos incluidos en los manuales de instrucciones del aparato Omega Speaker Systems DPS3301. Utilizando la vista previa online, puedes ver rápidamente el índice de contenidos y pasar a la página donde encontrarás la solución a tu problema con Omega Speaker Systems DPS3301.

Para tu comodidad

Si ver los manuales de instrucción de Omega Speaker Systems DPS3301 directamente en esta página no es cómodo para ti, puedes utilizar dos soluciones posibles:

  • Vista en pantalla completa – Para ver cómodamente los manuales de instrucciones (sin descargarlos en tu ordenador) puedes utilizar el modo de vista en pantalla completa. Para activar la vista del manual Omega Speaker Systems DPS3301 en pantalla completa, utiliza el botón Pantalla completa
  • Descargar al ordenador – también puedes descargar el manual de instrucciones de Omega Speaker Systems DPS3301 a tu ordenador y guardarlo en tu colección. Sin embargo, si no quieres ocupar espacio en tu dispositivo, siempre podrás descargarlo de ManualsBase.
Omega Speaker Systems DPS3301 Manual de instrucciones - Online PDF
Advertisement
« Page 1 of 26 »
Advertisement
Versión impresa

Muchas personas prefieren no leer el documento en la pantalla, sino en versión impresa. La opción de impresión también está prevista y puedes utilizarla haciendo clic en el enlace más arriba - Imprimir el manual. No tienes que imprimir el manual completo de Omega Speaker Systems DPS3301, solo las páginas que elijas. Ahorra papel.

Resúmenes

A continuación encontrarás resúmenes de los contenidos incluidos en las páginas posteriores del manual de instrucciones para Omega Speaker Systems DPS3301. Puedes utilizarlos si quieres ver rápidamente el contenido que se encuentra en la siguientes páginas del manual.

Resúmenes de contenidos
Resumen del contenido incluido en la página 1

http://www.omega.com
e-mail: info@omega.com
DPS3301 Series
Wall-Mount Programmable
Temperature Monitor

Resumen del contenido incluido en la página 2

SPECIFICATIONS .......................................................................................................................................................... 4 DESCRIPTION ................................................................................................................................................................ 5 THERMOCOUPLE OR RTD SELECTION................................................................................................................. 5

Resumen del contenido incluido en la página 3

RESETTING:................................................................................................................................................................... 16 ELECTRO-MECHANICAL RELAY OPTION....................................................................................................................... 16 Figure 2. Electro-mechanical Relays Hookup Example........................................................................................... 17 OPEN COLLECTOR O

Resumen del contenido incluido en la página 4

SPECIFICATIONS Typical @ 25 C and rated supply voltage unless otherwise specified. INPUTS: • Input types: J,K,T,E,R,S,B t/c, RTD, Voltage, Millivolt, Current & thermistor • Cold junction compensation error: +/- 0.5C max (10C to 40C) • Open thermocouple indication: ‘OPEN TC’ displayed OPTIONS: • 240Vac @ 50 Hz Power Supply • 15Vdc @ 1000ma. Power Supply • Open Collector output: 6 open collector transistors @ 50ma. sink each • Relay output: 6 SPST 1 Amp. @ 28Vdc, 0.5 Amp

Resumen del contenido incluido en la página 5

DESCRIPTION Housed in a wall-mount, water-tight plastic enclosure, the DPS3301 Series is a powerful temperature monitor/indicator. It accepts a single Thermocouple, RTD or Thermistor sensor input and then displays the temperature in either degrees C or F. In addition, it also monitors a number of useful functions such as high and low process readings, process run time, rate of process change etc. Keys are appropriately labeled, so that the user would not have to memorize their func

Resumen del contenido incluido en la página 6

How How to Reset and Program Th to Reset and Program Thermocou ermocouple Type ( ple Type (o or RTD) r RTD) A DPS3301- A DPS3301-TC that is calibrated for a J, K, T, or TC that is calibrated for a J, K, T, or E t E ty ype therm pe thermo ocouple or an RT couple or an RTD D m model odel m ma ay be y be programmed programmed for a specific therm for a specific thermo ocouple, or RTD ( couple, or RTD (385/392) t 385/392) type, ype, by by going i going in nto SETUP to SETUP m mode (Loo

Resumen del contenido incluido en la página 7

SEE SETUP ON HOW TO SELECT ONE OF THE DISPLAY MODES. RETAINING USER SETTINGS ON POWER DOWN DPS3301 saves all the programmed parameters in an EEPROM (electrically erasable programmable read only memory). An EEPROM stores the programmed parameters even when the power is removed from the unit. However, it is important to note that if the parameters are being changed during setup, they must be saved in the EEPROM by pressing and holding the ‘RESET’ key (till SAVING is displaye

Resumen del contenido incluido en la página 8

FLOW CHART SETUP PROGRAM PROGRAM LIMITS CONTROLLER SETPT PROGRAM LIMIT1 PROGRAM LIMIT2 DISPLAY TIME Configure Limit3 as DISPLAY OPTION Process or Rate a. Process b. Setpt Devn. c. In. Rate PROGRAM LIMIT3 d. Process High e. Process Low f. Elapsed Time Configure Limit4 as g. Timer 1 Count Process or Deviation h. Timer 2 Count i. Scan all PROGRAM LIMIT4 RATE Select Timer Modes TIMEBASE 0,1 or 2 PROGRAM TIMER1 COLD JUNCTION CALIBRATION PROGRAM TIME

Resumen del contenido incluido en la página 9

SETUP MODE Setup is used for configuring various parameters of DPS3301 unit. These parameters include entering limits, timers, dead-bands etc. Entering and Exiting Setup Mode: To get into setup mode, press and hold SETUP key. The display will show ELPSd t and then the value of elapsed time. Keep holding-in ‘SETUP’ key till the display shows ‘SETUP’ and starts scrolling the message 'EntEr PASSCOdE'. To return from SETUP to normal display/run mode, simply push and hold

Resumen del contenido incluido en la página 10

'PROGRAM CONTROLLER' MODE Display Time On entering Program Controller mode, the very first step lets you program is the display time. This determines the length of time (in seconds) that any VALUE is displayed before message, such as ‘PROCESS’ is flashed. The unit will first show 'dSPLy t' (for Display Time), and then the current setting in seconds. Use ‘^DIGv’ and ‘’ key to set the desired display time. Push ‘SETUP’ key following the selection. Display Option

Resumen del contenido incluido en la página 11

Cold Junction adjustment: After setting Heat/Cool mode, the next parameter is the cold junction reference temperature adjustment. The display will first show 'COLd JN' , and then the cold junction temperature will be indicated. Use ‘^DIGv’ key to adjust until the display reads the proper temperature. Once the correct temperature is displayed, push ‘SETUP’ key to enter that setting and go to temperature Calibration mode. NOTE 1: The unit comes pre-calibrated from the facto

Resumen del contenido incluido en la página 12

NOTE 1: The unit must be powered up for at least ten minutes before any adjustments are made. NOTE 2: For calibrating units with RTD or Thermistor inputs, connect the source to input connector, dial in a temperature near high end of the scale and adjust gain potentiometer on the back of the unit (See figure 7 for reference). Thermocouple type Selection: Next function is the last one in system setup. Here you select the type of thermocouple for which the unit has been calibr

Resumen del contenido incluido en la página 13

Programming Limit 3: As Process Limit: If Limit 3, in the above step, was configured as a Process limit, then the message displayed on entering this mode will be ‘PrG Lt3’. This will be followed by displaying the current value of Limit 3 . Use ‘’ key to move flashing to the next digit and ‘^DIGv’ key to increment/decrement the value of flashing digit. As Rate Limit: If Limit 3, in the above step, was configured as a Rate limit, then the message displayed on enter

Resumen del contenido incluido en la página 14

energized. In Mode 1 the timer is ON for a programmed amount of time after a temperature limit is reached (limit1 for Timer 1 and Limit 2 for Timer 2). When programmed amount of time has elapsed, the timer is de- energized. Mode 2 is used to produce a programmable time delay after the temperature limit is reached. After the delay, the timer output comes ON and stays ON until reset by the operator. For more details, refer to the TIMER MODES section. This mode is indicated by

Resumen del contenido incluido en la página 15

Audio Alarm On/Off: This unit supports an audio alarm option which comes on when ever a limit value is exceeded. This alarm can be turned On or Off, as desired. The selection is made by pushing ‘^DIGv’ key. If the alarm is ON, the display will read ‘ALR ON’ (Alarm On). Alternately, it will display ‘ALR OFF’ (for ‘Alarm Off’). Push ‘SETUP’ key after desired setting is displayed. This last push on SETUP key will also take you back to the very beginning of setup mode. To ge

Resumen del contenido incluido en la página 16

setpoing will be indicated. Deviation Alarm: Limit 4 has the capability to work either as process or as deviation alarm. This configuration is done during setup (look under SETUP). Also entered during setup is the alarm value. Programmed value is absolute and it works on negative as well as positive deviation e.g. if deviation alarm is set to 10, then output will get activated if process deviates –10 or +10 from the Setpoint. Resetting Deviation Alarm: Deviation alarm can

Resumen del contenido incluido en la página 17

limit alarms. (Check model number printed on the unit for option). If ordered with relays, then these relays are programmed during Setup to operate as Normally Open (NO) or Normally Closed (NC). The default setting is Normally Open. Each of these limit relays provides a switched output whenever a limit is reached. The maximum rating for a 120Vac unit is 120Vac @ 0.5 amp or 28 Vdc @ 1.0 amp. Figure 2. Electro-mechanical Relays Hookup Example PLUG-IN CONNECTOR SWITCHED OU

Resumen del contenido incluido en la página 18

To display Timer #1 value, push the TIME key twice. The first push shows elapsed time, while the second push will first display 'tr1 Cnt' (for Timer1 Count) and then Timer 1 value. To display Timer #2 value, push TIMER key three times. First two pushes display elapsed time and timer 1 value respectively, while the third push brings up timer 2 value on the display. This is , however, preceded by the message 'tr2 Cnt' (for Timer 2 Count). Resetting Timers: The two Timers can b

Resumen del contenido incluido en la página 19

HIGH AND LOW PEAKS A useful feature provided by the DPS3301 system is its ability to track high and low temperature peaks. This function is useful if a process must be left unattended for a long period of time, and it is necessary to find temperature extremes during the unattended period. High and low process peaks are displayed by pushing ‘HI/LO’ key. Pushing this key once will display the message 'HIGH Pt' (for High Point) and then the value of the highest temperature mon

Resumen del contenido incluido en la página 20

‘SIGNAL CONNECTOR’ in figure 4. Also indicated are the input signal’s positive and negative polarities for thermocouple connection. These markings are also on the printed circuit board in front of the connector. Care should be taken to connect the positive and negative legs of the signal source to the proper terminals on the connector. A wrong connection will result in incorrect process readings. (No polarity is necessary for RTD or thermistor). OUTPUT CONNECTOR PIN ASSIGNMENT


Manuales de instrucciones similares
# Manual de instrucciones Categoría Descargar
1 Omega Speaker Systems DPiTH-i32 Manual de instrucciones Pantalla 0
2 Omega Speaker Systems CNiTH-i32 Manual de instrucciones Pantalla 0
3 Omega Speaker Systems iLD Series Manual de instrucciones Pantalla 0
4 Omega Speaker Systems VR200 Manual de instrucciones Pantalla 0
5 Sony BVM-L170 Manual de instrucciones Pantalla 7
6 Sony DDM-2802CNU Manual de instrucciones Pantalla 1
7 Sony BVM-D20F1U, BVM-D20F1E, BVM-D20F1A, BVM-D24E1WU, BVM-D24E1WE, BVM-D24E1WA, BVM-D32E1WU, BVM-D32E1WE, BVM-D32E1WA Manual de instrucciones Pantalla 15
8 Sony 500A3WE Manual de instrucciones Pantalla 8
9 Sony CPD-17SF2 Manual de instrucciones Pantalla 10
10 Sony AEP MODEL CPD-E200E Manual de instrucciones Pantalla 9
11 Sony CPD-G400 Manual de instrucciones Pantalla 9
12 Sony CPD-E220E Manual de instrucciones Pantalla 5
13 Sony 500A3WJ Manual de instrucciones Pantalla 3
14 Sony CPD-110GS Manual de instrucciones Pantalla 1
15 Sony BVM-D SERIES BVM-D14H1E Manual de instrucciones Pantalla 14