Resumen del contenido incluido en la página 1
LCD4000
40" LCD Colour Monitor
User’s Manual
Resumen del contenido incluido en la página 2
Index Declaration of conformity ................................................................................................................................ English-1 Important Information ...................................................................................................................................... English-2 Warning, Caution ............................................................................................................................................ Engl
Resumen del contenido incluido en la página 3
DECLARATION OF CONFORMITY This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. U.S. Responsible Party: NEC-Mitsubishi Electronics Display of America, Inc. Address: 1250 North Arlington Heights Road, Suite 500 Itasca, Illinois 60143-1248 Tel. No.: (630) 467-3000 Type of Product: Co
Resumen del contenido incluido en la página 4
Important Information WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET. TO FULLY DISENGAGE THE
Resumen del contenido incluido en la página 5
Safety Precautions, Maintenance & Recommended Use FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE Please follow the bylaws or rules of your municipality to dispose FOLLOWING WHEN SETTING UP AND USING THE of the lamps properly. Immediately unplug your monitor from the LCD4000 LCD COLOUR MONITOR: wall outlet and refer servicing to qualified service personnel under the following conditions: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers • When the powe
Resumen del contenido incluido en la página 6
Contents Your new LCD4000 LCD monitor box* should contain the following: • LCD4000 LCD monitor • Power Cord (3 m) • PC - Video Signal Cable SC-B113 (4 m) • User’s Manual • Wireless Remote Control and AA Batteries • Clamper x 2 • Screw (M4 x 10) x 2 • CD-ROM • Ferrite Core x 4 • Stand for Independence x 2 Ferrite Core x 4 • Screw (M5 x 40 mm) for stand x 4 • Band x 3 Power Cord PC - Video Signal Cable (D-SUB to D-SUB Cable) Clamper x 2 Screw (M4 x 10) x 2 Stand for the Independence x 2 Screw CD-R
Resumen del contenido incluido en la página 7
Parts Name and Functions Control Panel buttons 1 POWER button ( ) 7 DOWN ( ) button Switches the power on/off. See also page 19. Activates the OSM menu when the OSM menu is turned-off. Acts as button to move the highlighted area down to select the adjustment with OSM menu. 2 MUTE button Switches the audio mute ON/OFF. EXIT button 8 Activates the OSM menu when the OSM menu is turned-off. 3 INPUT button Acts as EXIT button to move to previous menu with OSM menu. Acts as SET button with OSM menu.
Resumen del contenido incluido en la página 8
Terminal Panel 1 AC IN connector 6 AUDIO IN 1, 2, 3 Connects with the supplied power cord. To input audio signal from external equipment such as a computer, VCR or DVD player. 2 RGB 1 IN (DVI-D) 7 AUDIO OUT To input digital RGB signals from a computer having a digital RGB output. To output the audio signal from the AUDIO IN 3 jack. * This connector does not support analog input. 8 VIDEO VIDEO IN connector (BNC and RCA): To input a composite 3 RGB 2 IN (mini D-Sub 15 pin) video signal. BNC and RC
Resumen del contenido incluido en la página 9
Wireless Remote Control 5 4 3 6 MUTE button To switch the mute function on/off. 7 VOLUME UP button Increase the audio output level. 8 VOLUME DOWN button 1 Decrease the audio output level. 9 PIP (Picture In Picture) button 2 ON/OFF button: Toggle switches between PIP-ON/ 6 POP-ON/OFF. See page 23. 9 INPUT button: Select the “picture in picture” input signal. CHANGE button: Replaces to the main picture and sub 7 picture. 10 8 10 STILL button 13 ON/OFF button: To switch the still picture mode on/of
Resumen del contenido incluido en la página 10
Operating Range for the Remote Control Point the top of the remote control toward the LCD monitor’s Handling the remote control remote sensor during button operation. Use the remote control within a distance of about 7 m from * Do not subject to strong shock. the front of the LCD monitor’s remote control sensor and at * Do not allow water or other liquid to splash the remote a horizontal and vertical angle of within 30° within a distance control. If the remote control gets wet, wipe it dry of ab
Resumen del contenido incluido en la página 11
Setup Procedure 1. Determine the installation location 3. Connect external equipment (See pages 12~18) CAUTION: DO NOT ATTEMPT TO INSTALL THE LCD MONITOR BY YOURSELF • To protect the connected equipment, turn off the main power before making connections. Installing your LCD display must be done by a qualified • Refer to your equipment user manual. technician. Contact your dealer for more information. 4. Connect the supplied power cord CAUTION: MOVING OR INSTALLING THE LCD MONITOR MUST BE DONE BY
Resumen del contenido incluido en la página 12
How to Mount and Attach Options to the LCD Monitor You can attach mounting accessories to the LCD monitor in Ventilation Requirements for enclosure one of the following two ways: mounting To allow heat to disperse, leave space between surrounding In the upright position objects as shown in the diagram to the right. Ambient temperature should be less than 40°C. 100mm * 100mm 100mm * 100mm * Use some fans as needed. 100mm To avoid falling down Lay the screen face down Fasten the LCD monitor to wal
Resumen del contenido incluido en la página 13
How to install stand 1. Please turn monitor off. 2. Insert claws of monitor to stand holes until clicks. 3. Fasten 2 screws (M5 x 40) of both side. Torque 280 ~ 300N cm Screw M5 x 40 Hole of stand Claw of Monitor Stand How to remove the stand 1. Spread the protective sheet on the flat surface, such as a desk. 2. Place monitor on the protective sheet. 3. Remove 2 screws of each stand with a screw driver and keep them for reuse. English-11 English
Resumen del contenido incluido en la página 14
Connections Before making connections: * First turn off the power of all equipment to be attached. * Refer to the user manual in regard to this equipment. Wiring Diagram Personal computer LCD monitor DVD player Personal computer HD laser disk player VCR LCD monitor (second monitor) Equipment with digital interface Attaching the Ferrite Core Mounting Position of Ferrite Core Attach the Ferrite Core to PC Audio Cable and S-VIDEO Cable. Use of the cable without mounting the ferrite core will result
Resumen del contenido incluido en la página 15
Connecting a Personal Computer Connecting your computer to your LCD monitor will enable you to display your computer’s screen image. Some video cards may not be able to create a correct image resolution. Connect the LCD Monitor to a Personal Computer • To connect the RGB 2 IN connector (mini D-sub 15 pin) on the LCD monitor, use the supplied PC - Video RGB signal cable (mini D-sub 15 pin to mini D-sub 15 pin). • To connect the RGB 3 DVD/HD IN connector (BNC) on the LCD monitor, use a signal cabl
Resumen del contenido incluido en la página 16
® Connecting to a Macintosh Computer ® Connecting your Macintosh computer to your LCD monitor will enable you to display your computer’s screen image. Some video cards or drivers may not display images correctly. ® Connect the LCD Monitor to Macintosh • To connect the RGB 2 IN connector (mini D-sub 15 pin) on the LCD monitor, use the supplied PC - Video RGB signal cable (mini D-sub 15 pin to mini D-sub 15 pin). • To connect the RGB 3 DVD/HD IN connector (BNC) on the LCD monitor, use the signal c
Resumen del contenido incluido en la página 17
Connections with Digital Interface Equipment Connections can be made with equipment that is equipped with a digital interface compliant with the DVI (Digital Visual Interface) standard. Connect the LCD Monitor to a Computer with a Digital Output • The RGB 1 IN connector also accepts a DVI-D cable. • Input TMDS signals conforming to DVI standards. • To maintain display quality, use a cable with a quality prescribed by DVI standards. • The AUDIO IN 1 can be used for audio input. For connection, se
Resumen del contenido incluido en la página 18
Connecting a VCR Connecting your VCR or laser disc player to your LCD monitor will enable you to display your VCR’s or laser disc player’s video. Refer to your VCR or laser disc player owner’s manual for more information. Connect the LCD Monitor to a VCR or Laser Disc Player • Video signals can be connected to either the VIDEO IN [RCA or BNC] or the S-VIDEO IN connector. NOTE: S-VIDEO is priority input. Only one of the connectors, either RCA or BNC, can be used alternatively. • Video output will
Resumen del contenido incluido en la página 19
Connecting a DVD Player with component out Connecting your DVD player to your LCD monitor will enable you to display DVD video. Refer to your DVD player user’s manual for more information. Connect the LCD Monitor to a DVD Player • To connect the RGB 3 DVD/HD In connector (BNC) on the LCD monitor, use a separately available BNC connector cable. You will need a separately available BNC-to-RCA adapter to connect a DVD player with an RCA pin jack to the BNC connector cable. Some DVD players may have
Resumen del contenido incluido en la página 20
Connecting a Stereo Amplifier You can connect your stereo amplifier to your LCD monitor. Refer to your amplifier user’s manual for more information. Connect the LCD Monitor to a Stereo Amplifier • Turn on the LCD monitor and the amplifier only after all connections have been made. • Use an RCA cable to connect the AUDIO OUT connector (RCA) on the LCD monitor and the audio input on the amplifier. • Do not reverse the audio left and right jacks. • The AUDIO IN is used for audio input. • The AUDIO