Resumen del contenido incluido en la página 1
XT5888
15 INCH
COLOR MONITOR
USER'S
MANUAL
Features
• 0.28 mm Dot Pitch
• 1024 x 768, Non-Interlaced
• 90 Hz Refresh Rate (VGA/SVGA)
• Power Saving Operation (VESA DPMS)
• Non-Glare Screen
• Full Screen Display
• Low Radiation
Part #MAN074 Rev. 1.0 M1588L
Resumen del contenido incluido en la página 2
Table of Contents Section 1 - General Information ............................................................ 2 Section 2 - Installation ........................................................................... 3 Section 3 - Monitor Controls and LEDs................................................. 4 Section 4 - Troubleshooting................................................................... 5 Appendix A - Specifications ................................................................... 5
Resumen del contenido incluido en la página 3
Section 1 - General Information Congratulations on purchasing a MaxTech 15-inch Color Monitor. The monitor has one of the finest CRTs available in the industry, providing a full range of video display resolutions and complies with the MPR-I standard to reduce electromagnetic emissions. The monitor has a 0.28 mm dot pitch display with a 65 MHz video bandwidth. It supports video resolutions ranging from 640 x 350 to 1024 x 768 (non-interlaced). The monitor can be used with video cards supporting V
Resumen del contenido incluido en la página 4
Horizontal and Vertical Synchronization signals. This mode reduces the monitor’s power consumption to 8W. While in this mode the Power Indicator LED is amber. When the synchronization signals are re-enabled the monitor returns to normal operation. Section 2 - Installation 2.1 Attaching the Base Figure 2-1 Connecting the Base • Carefully place the monitor on its side or top. • Insert the hooks on the swivel base into the slots in the bottom of the monitor. Push down and forward on the base until
Resumen del contenido incluido en la página 5
• Attach the power cord to the monitor and plug it into an AC outlet. • The monitor is now ready for use. Section 3 - Monitor Controls and LEDs Figure 3-1 Monitor Controls 10 (on back) 1 2 9 8 7 6 5 4 3 1. Power Indicator: LED green: The monitor is in normal operating mode. LED amber: The monitor is in power saving mode. LED off: The power switch is off. 2. Power Switch: Push to turn the monitor on. Push again to turn the monitor off. 3. Brightness Control: Adjusts the display brightness. 4. Co
Resumen del contenido incluido en la página 6
7. Vertical-Size Adjusts the display height. 8. Vertical-Position Adjusts the vertical position. 9. Pincushion Adjusts the shape of the left and right sides of the display. 10. Rotation Control (rear of unit) Adjusts display tilt. Section 4 - Troubleshooting No picture, power indicator off • Check AC cord is plugged into outlet and monitor. • Turn on the power switch. No picture, power indicators on. • Adjust brightness and contrast controls. No picture, power indicator amber. • Monitor is in D
Resumen del contenido incluido en la página 7
Synchronization Horizontal: 30-60 KHz Vertical: 50-90 Hz Deflection Geometric distortion H<=2.5mm, V<=2.5mm Linearity distortion H<=10%, V<=8% Pincushion distortion <=2mm High voltage regulation H<=4mm, V<=4mm(0-25FL) Low radiation MPR-I specification Front controls Power, Brightness, Contrast, Horizontal-Size, Horizontal- Position, Vertical-Size, Vertical-Position, Pincushion Rear Control Display Tilt Power saving Display Power Management Signaling (DPMS) SUSPEND mode 30W (Max.) OFF mode 8W (Ma
Resumen del contenido incluido en la página 8
Except as specified below, this warranty covers all defects in material or workmanship in this product. The following are not covered by the warranty: 1. Any product which is not distributed in North America by MaxTech or which is not purchased in North America from an authorized MaxTech Dealer. 2. Any product on which the serial number has been defaced, modified or removed. 3. Damage, deterioration or malfunction resulting from: a. Accident, misuse, abuse, neglect, fire, water, lightning or oth
Resumen del contenido incluido en la página 9
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interferen
Resumen del contenido incluido en la página 10
9
