Resumen del contenido incluido en la página 1
® ®
TLM100
Tank Level Monitor
User’s Manual
Revision 1.3
Copyright © 2010 Maretron, LLP All Rights Reserved
Maretron, LLP
rd
9014 N. 23 Ave #10
Phoenix, AZ 85021
http://www.maretron.com
Maretron Manual Part #: M002201
Revision 1.3 Page i
Resumen del contenido incluido en la página 2
TLM100 User’s Manual Revision History Revision Description 1.0 Original document 1.1 Corrected typo in NMEA protocol PGN list 1.2 Typographical corrections 1.3 Added documentation on mounting locations and theory of operation Corrected torque specifications Added prohibition of red Loctite threadlocking compound and cleaning agents containing acetone Updated troubleshooting section Updated referenced firmware version number Typographical corrections Page ii Revisio
Resumen del contenido incluido en la página 3
® ® Table of Contents 1 General ................................................................................................................................ 1 1.1 Introduction .................................................................................................................... 1 1.2 Gasoline Tanks .............................................................................................................. 1 1.3 Firmware Revision ..................................
Resumen del contenido incluido en la página 4
TLM100 User’s Manual Table of Figures Figure 1 - TLM100 Operation .................................................................................................... 3 Figure 2 – TLM100 Mounting – SAE 5-Hole Bolt Pattern .......................................................... 6 Figure 3 – Mounting TLM100 to SAE 5-Hole Tank with Focus Tube ......................................... 7 Figure 4 – TLM100 Mounting With Threaded Adapter .................................................
Resumen del contenido incluido en la página 5
® ® 1 General 1.1 Introduction Congratulations on your purchase of the Maretron Tank Level Monitor (TLM100). Maretron has designed and built your monitor to the highest standards for years of reliable, dependable, and accurate service. The TLM100 is used to sense levels of liquid tanks using ultrasonic technology and transmit ® the liquid levels over the NMEA 2000 network. This allows you to observe tank levels ® anywhere on the vessel where there is an NMEA 2000 compatible display s
Resumen del contenido incluido en la página 6
TLM100 User’s Manual 1.5 TLM100 Accessories Maretron offers the following accessories for the TLM100: • TA-5H-1.5NPT 1.5” NPT Displacement Hull Tank Adapter • TA-5H-1.25BSP 1.25” BSP Displacement Hull Tank Adapter • TFT-5H SAE 5-Bolt Pattern Non-Displacement Hull Focus Tube • TFT-1.5NPT 1.5” NPT Non-Displacement Hull Focus Tube • TFT-1.25BSP 1.25” BSP Non-Displacement Hull Focus Tube • TAL-5H SAE 5-Bolt Pattern Black Water Airlock • TAL-1.5NPT 1.5” NPT Black Water Airlock •
Resumen del contenido incluido en la página 7
® ® then be received back at the sensor component. Using the speed of sound, it uses this time to calculate the distance between the face of the sensor component and the surface of the liquid (or the tank bottom if the tank is empty). The cone width of the beam transmitted by the TLM100 sensor component is 6°. Please refer to Figure 1 below for a diagram of the waves emitted and received by the TLM100. Please note that due to limitations of ultrasonic technology, the minimum depth that
Resumen del contenido incluido en la página 8
TLM100 User’s Manual • The sensor component of the TLM100 must be mounted over the deepest part of the tank, in order to obtain accurate depth readings when the tank is empty or near empty. • In order to obtain accurate readings when the tank is empty, the tank bottom directly under the TLM100 must be both smooth and flat, so that the ultrasonic sound waves transmitted by the sender are reflected back to the sender for measurement. If the tank bottom under the TLM100 is sloped, groove
Resumen del contenido incluido en la página 9
® ® 2.4 Mounting the TLM100 2.4.1 Mounting the TLM100 Sensor Component The TLM100 comes from the factory ready to mount on a tank with the standard SAE J1810 5- Hole mounting pattern. Maretron offers adapters to allow mounting the TLM100 on a tank with a 1.5” NPT connection or a 1.25” BSP connection. WARNING • Gasket installs only one way and must be properly aligned to the tank and sensor for proper operation • Use only supplied gasket – other gaskets may obstruct and render devic
Resumen del contenido incluido en la página 10
TLM100 User’s Manual Mounting Screws (x5) TLM100 Sensor Component TLM100 Gasket SAE 5-Bolt Tank Fitting TLM100 Interface Component Figure 2 – TLM100 Mounting – SAE 5-Hole Bolt Pattern 2.4.1.2 Installation on a Tank with a SAE J1810 5-Bolt Fitting and Focus Tube If a focus tube is used for a tank with a SAE J1810 5-bolt fitting, determine the depth of the tank at the location of the tank sensor mounting hole and use a saw with a metal-cutting blade to trim the focus tube so
Resumen del contenido incluido en la página 11
® ® Mounting Screws (x5) TLM100 Sensor Component TLM100 Gasket Focus Tube Focus Tube Gasket SAE 5-Bolt Tank Fitting TLM100 Interface Component 1” (2.54cm) clearance between focus tube and tank bottom Figure 3 – Mounting TLM100 to SAE 5-Hole Tank with Focus Tube 2.4.1.3 Installation on a Tank with a SAE J1810 5-Bolt Fitting and Airlock Installation of the TLM100 on a tank with a SAE J1810 5-bolt fitting with an airlock is identical to installation with a focus tube, except t
Resumen del contenido incluido en la página 12
TLM100 User’s Manual Mounting Screws (x5) TLM100 Sensor Component TLM100 Gasket Threaded Adapter Threaded Tank Fitting TLM100 Interface Component Figure 4 – TLM100 Mounting With Threaded Adapter 2.4.1.5 Installation on a Tank with a 1.25”BSP or 1.5”NPT Threaded Tank Fitting and Focus Tube If a focus tube is used for a tank with a SAE J1810 5-bolt fitting, determine the depth of the tank at the location of the tank sensor mounting hole and use a saw with a metal-cutting bla
Resumen del contenido incluido en la página 13
® ® Mounting Screws TLM100 Sensor Component TLM100 Gasket Threaded Focus Tube Threaded Tank Fitting TLM100 Interface Component 1” (2.54cm) clearance between focus tube and tank bottom Figure 5 – Mounting TLM100 with Focus Tube on Threaded Tank Fitting 2.4.1.6 Installation on a Tank with a 1.25”BSP or 1.5”NPT Threaded Tank Fitting and Airlock Installation of the TLM100 on a tank with a 1.25” BSP or 1.5” NPT threaded tank fitting with an airlock is identical to installation w
Resumen del contenido incluido en la página 14
TLM100 User’s Manual 2.5 Connecting the TLM100 ® There is one connection point (see Figure 6) for the TLM100: the NMEA 2000 connection. ® Please refer to Section 2.5.1 for making NMEA 2000 connection. Cable to NMEA 2000 Sensor Connector Component Figure 6 – TLM100 Connections ® 2.5.1 Connecting to NMEA 2000 Interface ® The Maretron TLM100 provides a connection to an NMEA 2000 interface through a five pin ® male connector (see Figure 7). You connect the TLM100 to an NMEA 2000
Resumen del contenido incluido en la página 15
® ® 3 Configuring the TLM100 The TLM100 has several configurable parameters, which are shown below including the default values. If you are not using the default values, then you will need to refer to the corresponding section for configuring the TLM100 appropriately. 1. Tank Type (Section 3.1) – Default is Fuel 2. Tank Number (Section 3.2) – Default is Tank 0 3. Tank Capacity (Section 3.3) – Default is No Tank Capacity Transmitted 4. Tank Depth or Custom Calibration (Section 3.4) –
Resumen del contenido incluido en la página 16
TLM100 User’s Manual software. Refer to the user’s manual of the particular product that will be used for configuring the TLM100 as these manuals provide detailed instruction on configuration procedures. 3.4 Tank Depth or Custom Calibration The TLM100 can be easily programmed for use with tanks of rectangular cross-section (see Section 3.4.1). For non-rectangular tank shapes, you can perform custom calibration so that the TLM100 accurately reflects fluid levels (see Section 3.4.2).
Resumen del contenido incluido en la página 17
® ® Symptom Troubleshooting Procedure ® No tank level 1. If operating in the NMEA 2000 Mode, check the connection to the ® output NMEA 2000 interface (see Section 2.5.1) and tighten if necessary. ® 2. Ensure that power is supplied to the NMEA 2000 network. Proper network power can be checked by measuring the voltage at an open tee between NET-S and NET-C. The voltage should be between 9 and 16 volts. 3. Ensure that both trunk line terminators are in place. Proper network termination
Resumen del contenido incluido en la página 18
TLM100 User’s Manual 6 Technical Specifications Specifications Parameter Value Comment Accuracy ±2% Resolution ±1% Number of Tank Types 16 Fuel, Fresh Water, Waste Water, Live Well, Oil, etc. Number of Tanks per Tank Type 16 16 Tanks per Tank Type Numbered 0-15 Maximum Tank Depth 40” (1.02m) Minimum Depth Reading 2” (5.08cm) Sensor Deadband Support for Irregularly Shaped Yes Can be Calibrated for any Shape Tank Tanks Programmable Tank Capacity Yes Allows Displays to Calculate
Resumen del contenido incluido en la página 19
® ® Mechanical Parameter Value Comment Size 3.9”” x 1.2” x 1.0” Interface Component (99mm x 30.5mm x 25.4mm) 2.7” dia. X 0.9” Sensor Component (68.6mm dia. x 22.9mm) 8.5” (215.9mm) Interconnecting Cable Weight 12 oz. (340g) Mounting SAE J1810 5-hole bolt Can mount to 1.25” BSP or 1.5” NPT using pattern available adapters Environmental Parameter Value IEC 60945 Classification Exposed Degree of Protection IP67 Operating Temperature -25°C to 55°C Storage Temperature -40°C
Resumen del contenido incluido en la página 20
TLM100 User’s Manual 8 Maretron (2 Year) Limited Warranty Maretron warrants the TLM100 to be free from defects in materials and workmanship for two (2) years from the date of original purchase. If within the applicable period any such products shall be proved to Maretron’s satisfaction to fail to meet the above limited warranty, such products shall be repaired or replaced at Maretron’s option. Purchaser's exclusive remedy and Maretron’s sole obligation hereunder, provided product is