Resumen del contenido incluido en la página 1
User’s Guide
L226WT
L226WTX
L226WTQ
L226WTG
L226WTM
L226WTY
L226WTP
Make sure to read the Important Precautions before using the product.
Keep the User's Guide(CD) in an accessible place for future reference.
See the label attached on the product and give the information to your
dealer when you ask for service.
Resumen del contenido incluido en la página 2
Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the power cord supplied with the unit. In case you use another power cord, make sure that it is certified by the applicable national stan
Resumen del contenido incluido en la página 3
Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation. If these openings are blocked, built-up heat can cause failures wh
Resumen del contenido incluido en la página 4
Connecting the speakers - The feature is only for speaker models - L226WTM Connecting the speaker 1. Place the monitor with its front facing downward on a soft cloth. 2. Insert the protruding hook of the speaker in the direction of the slot in the back of the product. Slot Hook Audio DC-In AUDIO IN Cable 3. After setting up the speaker, connect the Audio DC-In Cable to the back of the product. DC-OUT A3
Resumen del contenido incluido en la página 5
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connecting the stand 1. Place the monitor with its front facing downward on a soft cloth. 2. Assemble the Stand Body into the product in the correct direction as shown in the picture. Make sure you push it until you hear it “click”. Hinge Body Stand Body 3. Assemble the Stand Base(Front, Rear) into the Stand Body in the correct direction. 4
Resumen del contenido incluido en la página 6
Connecting the Display Disassembling the stand Type. A 1. Put a cushion or soft cloth on aflat 2. Place the monitor face Down on surface. the cushion or soft cloth. 3. Pushing Latch inside, Take the stand base from stand body. 4. Separate the stand using a screwdriver as shown in the picture. Note: Please keep the 4 screws in an accessible place for future use. 5. Pack up the product as shown in the picture. A5
Resumen del contenido incluido en la página 7
Connecting the Display Disassembling the stand Type. B 1. Put a cushion or soft cloth on aflat 2. Place the monitor face Down on surface. the cushion or soft cloth. 3. Change your hold on the product as it follows and turn the Stand Base in the arrow direction. 4. Pull out the Stand to remove. 5. Pushing Latch inside, Take the stand 6. Pack up the product as shown in the base from stand body. picture. A6
Resumen del contenido incluido en la página 8
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5˚~20˚ 20 Swivel : 355˚ Ergonomic It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees. A7
Resumen del contenido incluido en la página 9
Connecting the Display Using the Computer 1. Make sure to turn off the computer and product. Connect the cable as below sketch map 1 2 form to . A Connect DVI Cable B Connect Dsub Cable (PC) C Connect Dsub Cable (Mac) Analog signal Digital signal Power Cord D-sub DVI Wall-outlet type PC PC-outlet type PC DVI-D(This feature is not available in all countries.) PC MAC Mac adapter For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-sub VGA connecto
Resumen del contenido incluido en la página 10
Using the speakers - The feature is only for speaker models - L226WTM Side Jack Headphone/Earphone Input Rear Connects to the *LINE OUT jack of the PC sound card. AUDIO IN Speaker Out *Line Out A9
Resumen del contenido incluido en la página 11
Control Panel Functions Front Panel Controls 6 (-) (+) Control Function At the current display, Use 'ez Zooming' Key, then the display ZOOMING resolution is transferred to the one step low resolution. Use 'ez Zooming' Key one more, the display is back to the original display. *Only One touch of ez-zoom, you can fine the best resolution you want and it is possible to magnify the size of characters and pictures for the old not having good eye sight, housewives not dealing with computer well and ch
Resumen del contenido incluido en la página 12
Control Panel Functions Control Function Use these buttons to select or adjust functions in the On - + Buttons Screen Display. For more information, refer to page A18. (-) (+) Use this button to make D-Sub or DVI connector active. (SOURCE Hot key) This feature is used when two computers are connected to the display. The default setting is D-Sub. AUTO/SET Use this button to enter a selection in the On Screen Display. Button AUTO IMAGE ADJUSTMENT When adjusting your display settings, always pre
Resumen del contenido incluido en la página 13
On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD. NOTE Allow the display to stabilize for at least 30 minutes before making image adjustments. To make a
Resumen del contenido incluido en la página 14
On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. Main menu Sub-menu A D Reference BRIGHTNESS PICTURE To adjust the brightness, contrast and gamma of the CONTRAST screen GAMMA sRGB COLOR To customize the color of PRESET 6500K the screen 9300K RED GREEN BLUE To adjust the position of the HORIZONTAL screen POSITION VERTICAL CLOCK To improve the clarity and PHASE TRACKING stabilit
Resumen del contenido incluido en la página 15
On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MENU Button, then the main menu of the OSD appears. PICTURE Menu Name Sub-menus Icons Button Tip MENU : Exit : Adjust (Decrease/Increase) + - SET : Enter : Select another sub-menu NOTE OSD (On Screen Display) menu languages on the mon
Resumen del contenido incluido en la página 16
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description PICTURE PICTURE BRIGHTNESS To adjust the brightness of the screen. CONTRAST To adjust the contrast of the screen. GAMMA Set your own gamma value. : -50/0/50 On the monitor, high gamma values display whitish images and low gamma values display high contrast images. MENU : Exit : Decrease - : Increase + SET : Select another sub-menu COLOR COLOR • sRGB: Set the screen color to fit the PRESET SRGB standard color spec
Resumen del contenido incluido en la página 17
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description POSITION POSITION HORIZONTAL To move image left and right. VERTICAL To move image up and down. MENU : Exit - : Decrease + : Increase SET : Select another sub-menu TRACKING TRACKING CLOCK To minimize any vertical bars or stripes visible on the screen background. The horizontal screen size will also change. PHASE To adjust the focus of the display. This item allows you to remove any horizontal noise and clear or sh
Resumen del contenido incluido en la página 18
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description LANGUAGE To choose the language in which the control names are displayed. SETUP OSD To adjust position of the OSD window POSITION on the screen. SETUP WHITE If the output of the video card is different BALANCE the required specifications, the color level may deteriorate due to video signal distortion. Using this function, the signal level is adjusted to fit into the standard output level of the video card in order to
Resumen del contenido incluido en la página 19
On Screen Display(OSD) Selection and Adjustment (-) The OSD screen will appear when you touch the button on the left side of the monitor. Menu Name Icons Sub-menu Name FLATRON F-ENGINE Screen when applied Screen when not applied When you execute F-ENGINE, two tones will appear on the screen as shown. The applied screen will appear on the left side, whereas the non-applied screen will appear on the right side.Touch the SET button to use the adjusted screen. Main menu S
Resumen del contenido incluido en la página 20
Troubleshooting Check the following before calling for service. No image appears No image appears Is the power cord of the • Check and see if the power cord is connected display connected? properly to the power outlet. Is the power indicator • Press the Power button. light on? • Adjust the brightness and the contrast. Is the power on and the power indicator blue or green? Is the power indicator • If the display is in power saving mode, try moving the mouse or pressing any key on the keyb
