Resumen del contenido incluido en la página 1
Color Monitor
P260
EN
Operating Instructions
F
Mode d’emploi
D
Bedienungsanleitung
ES
Manual de instrucciones
I
Istruzioni per l’uso
Resumen del contenido incluido en la página 2
Resumen del contenido incluido en la página 3
DANGER To avoid shock hazard: • Do not remove the covers. • Do not operate this product unless the stand is attached. • Do not connect or disconnect this product during an electrical storm. • The power cord plug must be connected to a properly wired and grounded power outlet. • Any equipment to which this product will be attached must also be connected to properly wired and grounded power outlets. • To isolate the monitor from the electrical supply, you must remove the plug from the power outlet
Resumen del contenido incluido en la página 4
PELIGRO Para evitar riesgos de descargas eléctricas: • No retire bajo ningún concepto las cubiertas. • No maneje el monitor sin antes acoplar el soporte. • No conecte ni desconecte el equipo de una toma de alimentación durante una tormenta eléctrica. • El cable de alimentación debe estar conectado a un enchufe debidamente cableado y con toma de tierra. • Cualquier equipo al que se vaya a conectar este producto también debe estar conectado a tomas de alimentación cableadas y conectadas a tierra
Resumen del contenido incluido en la página 5
FARE Slik unngår du fare for elektrisk støt: • Ikke ta av dekslene. • Ikke bruk produktet dersom sokkelen ikke er montert. • Ikke koble produktet til eller fra under tordenvær. • Pluggen på strømledningen må kobles til korrekt montert og jordet strømuttak. • Utstyr som dette produktet eventuelt blir koblet til, må også kobles til korrekt montert og jordet strømuttak. • For å isolere skjermen fra strømkilden må du ta ut pluggen fra strømuttaket. Strømuttaket bør være lett tilgjengelig. Käsittely:
Resumen del contenido incluido en la página 6
TEHLÜKE Elektrik arpmasÝ tehlikesinden kaÝnmak iin: • KapaklarÝ ÝkarmayÝnÝz. • Bu cihazÝ kaidesine takÝlÝ durumda deÛilken alÝßtÝrmayÝnÝz. • Bu cihazÝ elektriksel fÝrtÝna sÝrasÝnda prize takmayÝnÝz veya prizden ÝkarmayÝnÝz. • Elektrik kablosunun fißi, elektrik ve toprak baÛlantÝlarÝ usulne uygun olarak yapÝlmÝß bir prize takÝlmalÝdÝr. • Bu cihazÝn baÛlanacaÛÝ diÛer tm cihazlar da elektrik ve toprak baÛlantÝlarÝ usulne uygun olarak yapÝlmÝß prize takÝlmÝß olmalÝdÝr. • Monitrn elektrikl
Resumen del contenido incluido en la página 7
English EN
Resumen del contenido incluido en la página 8
Edition 1 This publication could contain technical inaccuracies or typographical errors. Changes are made periodically to the information herein; these changes will be made in later editions. IBM may make improvements and/or changes in the product(s) and/or program(s) at any time. It is possible that this publication may contain reference to, or information about, IBM products (machines and programs), programming, or services that are not announced in your country. Requests for copies of this pu
Resumen del contenido incluido en la página 9
TABLE OF CONTENTS Getting started Precautions ............................................................................................................................2 Identifying Parts and Controls ...........................................................................................3 Setup .......................................................................................................................................4 Selecting the Input Signal ..................................
Resumen del contenido incluido en la página 10
Getting started Getting Started Use of the Tilt-Swivel Precautions This monitor can be adjusted within the angles shown Installation below. To find the center of the monitor’s turning radius, align the center of the monitor’s screen with the centering • Prevent internal heat build-up by allowing adequate air dots on the stand. circulation. Do not place the monitor on surfaces (rugs, Hold the monitor at the bottom with both hands when you blankets, etc.) or near materials (curtains, draperies) th
Resumen del contenido incluido en la página 11
Getting Started Identifying Parts and Controls See the pages in parentheses for further details. Front Rear AC IN (HD15) (DVI) 1 2 1- -2 EN 1? (reset) button (page 15) 8 AC IN connector (page 4) Resets the adjustments to the factory settings. Provides AC power to the monitor. 2 ASC (auto sizing and centering) button 9 Video input 1 connector (HD15) (J1) (page 5) (page 4) Automatically adjusts the size and centering of the Inputs RGB video signals (0.700 Vp-p, positive) and picture. sync signals
Resumen del contenido incluido en la página 12
Getting Started Rear Setup This monitor works with platforms running at horizontal frequencies between 30 and 121 kHz. AC IN (HD15) (DVI) 1 2 Step 1: Make sure the computer and monitor are switched off Step 2: Connect the monitor to the computer Connect the video signal cable to the video output of the computer. To a computer 0 Video input 2 connector (DVI) (J2) (page forward side with a DVI 4) video output Connected to a computer with a DVI video output. rear side AC IN (HD15) (DVI) 1 2 C5 1 2
Resumen del contenido incluido en la página 13
Getting Started Step 5: Adjust the monitor’s controls Selecting the Input Signal according to your personal You can connect two computers to this monitor using the preference video input 1 (J1) and video input 2 (J2) connectors. To select one of the two computers, use the input switch. The installation of your monitor is complete. Move the input switch. Note The selected connector appears on the screen for 3 seconds. If no picture appears on the screen and “NO INPUT SIGNAL” or “OUT OF SCAN RANGE
Resumen del contenido incluido en la página 14
Customizing Your Monitor Customizing Your Monitor Before adjusting Introducing the On-screen • Connect the monitor and the computer, and turn them on. Display System Selecting the On-screen Display Most adjustments are made using the MENU OSD. Language MENU OSD If you need to change the OSD language, see “Using the Press the button to display the MENU OSD. LANGUAGE On-screen Display” on page 13. This MENU OSD contains links to the other OSDs described The default setting is English. below. MEN
Resumen del contenido incluido en la página 15
Customizing Your Monitor 4 Press the ?// buttons to adjust the settings. Using the SIZE/CENTER On- screen Display The SIZE/CENTER settings allow you to adjust the picture’s size, centering, or zoom. Once the setting is adjusted, it will be stored in memory for Select To the current input signal. / . . . to increase picture width (Horizontal Sizing) ? . . . to decrease picture width 1 Press the button. The MENU OSD appears. / . . . to increase picture height (Vertical Sizing) ? . . . to decreas
Resumen del contenido incluido en la página 16
Customizing Your Monitor 4 Press the ?// buttons to adjust the settings. Using the GEOMETRY On- screen Display The GEOMETRY settings allow you to adjust the shape and orientation of the picture. Once the (Rotation) is adjusted, it will be stored in For Press memory for all input signals received. All other adjustments (Rotation) / . . . to rotate the picture clockwise will be stored in memory for the current input signal. 1 Press the button. ? . . . to rotate the picture counterclockwise The
Resumen del contenido incluido en la página 17
Customizing Your Monitor 4 Press the ?// buttons to adjust the settings. Using the CONVERGENCE On- screen Display The CONVERGENCE settings allow you to adjust the quality of the picture by controlling the convergence. The convergence refers to the alignment of the red, green, For Press and blue color signals. / . . . to shift red shadows to the right If you see red or blue shadows around letters or lines, adjust and blue shadows to the left (Horizontal Convergence) the convergence. ? . . . to s
Resumen del contenido incluido en la página 18
Customizing Your Monitor Select To Using the SCREEN On-screen LANDING reduce any color irregularities in the Display screen’s top left corner to a minimum. LANDING reduce any color irregularities in the The SCREEN settings allow you to adjust the quality of the screen’s top right corner to a minimum. picture by controlling the moire and landing. LANDING reduce any color irregularities in the • If the color is irregular at the corners of the screen, adjust screen’s bottom left corner to a the la
Resumen del contenido incluido en la página 19
Customizing Your Monitor EASY mode Using the COLOR On-screen COLOR Display EASY EXPERT s RGB 5000K 6500K 930 0K The COLOR settings allow you to adjust the picture’s color 50 0 0K temperature by changing the color level of the white color COLOR field. Colors appear reddish if the temperature is low, and RETURN ON bluish if the temperature is high. This adjustment is useful for matching the monitor’s color to a printed picture’s colors. 1 First press the ./> buttons to select the color temperatur
Resumen del contenido incluido en la página 20
Customizing Your Monitor 3 Press the ./> buttons to select the adjustment item Note 3, then press the ?// buttons to adjust the GAIN Your computer and other connected products (such as a printer), must be sRGB compliant. (white level). This adjusts the light areas of an image. COLOR EASY EXPERT s RGB You can adjust the R (red), G (green), B (blue) component of the input signal when making changes to :56 : 76 FOR s RGB items 2 and 3. COLOR RETURN ON If you fine tune the color temperature, the new
