Manual de instrucciones de Audiovox VOD86

Resumen del contenido incluido en la página 1

VOD86
8.5" OVERHEAD
LCD MONITOR WITH
DVD PLAYER

Resumen del contenido incluido en la página 2

Important Notice An LCD panel and/or video monitor may be installed in a motor vehicle and visible to the driver if the LCD panel or video monitor is used for vehicle information, system control, rear or side observation or navigation. If the LCD panel or video monitor is used for television reception, video or DVD play, the LCD panel or video monitor must be installed so that these features will only , function when the vehicle is in "park" or when the vehicle s parking brake is applied.

Resumen del contenido incluido en la página 3

MATERIALS INCLUDED IN THIS PACKAGE: 1) 8.5” TFT LCD Overhead Monitor With DVD Player - (1pc) 2) 12 Pin Power / Signal harness (P/N 112-3959) - (1pc) 3) 2 Pin Power Wire Harness with choke (P/N 112B3143) - (1pc) 4) Hardware Package Screws ISO M3 x 8mm Long - (5pcs) #4 x 5/16" Self Drilling Screws - (1pc) #4 x 7/16" Self Drilling Screws - (3pcs) #8 x 3/8" Self Drilling Screws - (4pcs) M5 Screws - (4pcs) 5) Remote Control (P/N 136-4196) - (1pc) 6) Universal Mounting Bracket (P/N 108-3921) - (1pc)

Resumen del contenido incluido en la página 4

5. Cap L & R 4

Resumen del contenido incluido en la página 5

Resumen del contenido incluido en la página 6

GENERAL INSTALLATION APPROACH: 1) Decide upon system configuration and options that will be installed (i.e.: what components, VCP, Video Game, external amp, wireless headphones, VCP, etc.). 2) Review all manuals to become familiar with electrical requirements and hook ups. 3) Decide upon mounting locations of all components and method of mounting. 4) Prep the vehicle by removing any interior trim necessary to gain access to vehicle's wiring aswell as all areas where interconnecting wire harnes

Resumen del contenido incluido en la página 7

4) Once the mounting location of the monitor has been determined, there may be additional preparation work necessary, depending on the vehicle structure and installation method. Some of the steps that may be required are: A) Removal of the vehicle's dome light B) If the trim ring will be used, it may have to be trimmed to fit the contour of the vehicle's headliner. Refer to the "Trim Ring Installation" section in this manual. TRIM RING INSTALLATION: Note: This page only covers special instal

Resumen del contenido incluido en la página 8

MOUNTING THE TRIM RING Roof Roof Support Headliner Mounting Bracket Self-drilling Screws Trim Ring Video Unit M5 Screw VOD86 1) Make the connections to the vehicle for the 12 pin wiring harness. , 2) Connect power harness to vehicle s electrical system by tapping into an accessory hot line and a good ground. 3) Connect the 12 pin harness to the mating connector on the Video Monitor. 4) Verify all functions of the System before final mounting of the finished assembly. A/V Source Definitions: 1.

Resumen del contenido incluido en la página 9

VOD86 * Optional Relay Box SIRSWB 12 Pin Power / Signal harness 2 Pin Power Auxillary Video Display Wire Harness with choke Figure A 9 Line Out-L (White) Line Out-R (Red) Line Out-V (Yellow) Line Out-L (White) Line Out-R (Red) Line Out-V (Yellow)

Resumen del contenido incluido en la página 10

CONNECTING THE DOME LIGHTS The dome lights in the video monitor require three connections to the vehicle's wiring. There are two common types of dome light circuits used, positive or negative switched. Positive systems supply voltage to the interior lights to turn them on, negative switched systems apply ground to illuminate the bulbs. To determine which system you have you must locate the wires at the dome light. On a positive switched system, with all the doors closed and the lights out, b

Resumen del contenido incluido en la página 11

Negative Switched Dome Lighting Red / black - Lamp on To 12 pin Black / red - Lamp common Purple / brown - Lamp Auto connector To constant To constant Factory Door ajar switch or Body Control computer Troubleshooting: SYMPTOM: REMEDY: No power at Video Monitor Verify +12 VDC on Red wire at 2 pin Power Harness behind video monitor. Verify ground connection with continuity test from known good ground to black wire at 2 pin Power Harness Power but no video or sound Verify that the correct source

Resumen del contenido incluido en la página 12

WWW C 2008 Audiovox Electronics Corp. 150 Marcus Blvd. Hauppauge, NY 11788 128-8343