Resumen del contenido incluido en la página 1
SyncMaster 591s / 591v / 793s / 793v / 783DF / 793DF /
793MB / 795DF / 795MB / 797DF / 997DF
Install drivers Install programs
Resumen del contenido incluido en la página 2
Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock Power When not used for extended periods of time, set your computer to a screen saver. If the same image is present for long periods of time, Phosphor Burnt can be occured, or the screen m
Resumen del contenido incluido en la página 3
This may cause an electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause an electric shock or fire. Use only a properly grounded plug and receptacle. An improper ground may cause electric shock or equipment damage. Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage. This may cause an electric shock or fire. Disconnect the plug from the outlet
Resumen del contenido incluido en la página 4
Installation Put your monitor in a location with low humidity and a minimum of dust. Failure to do so may cause an electric shock or fire inside the monitor. Do not drop the monitor when moving it. This may cause damage to the product or human body. Install the monitor base in a showcase or shelf so that the end of the base does not project beyond the showcase or shelf. Dropping the product may cause damage to the product or personal injury. Set down the monit
Resumen del contenido incluido en la página 5
Clean When cleaning the monitor case or the surface of the CDT, wipe with a slightly moistened, soft fabric. Do not clean Flat monitor with water. Use a water-diluted mild detergent. (Some detergents contain significant amounts of alcohol-based solvents, which can damage (color change) or crack the monitor case. The antiglare/anti-static surface coating on the CDT may also be affected.) Dilute the detergent (1:10 ratio) with water before using. Do not spray water or de
Resumen del contenido incluido en la página 6
Do not cover the vents on the monitor cabinet. Bad ventilation may cause a breakdown or fire. Do not set a glass of water, chemicals or any small metal objects on the monitor. This may cause damage, electric shock or fire. If a foreign substance gets into the monitor, disconnect the plug and then contact a service center. For each hour of looking at the monitor, you should let your eyes rest for 5 minutes. This will reduce eye fatigue. Watching the monitor cont
Resumen del contenido incluido en la página 7
Keep the monitor away from any magnetic substances. This may cause discoloring or distortion of the image. Do not install the product on an unstable, uneven surface or a location prone to vibrations. Dropping the product may cause damage to the product or personal injury. Using the product in a location prone to vibrations may shorten the lifetime of the product or may catch fire.
Resumen del contenido incluido en la página 8
Hoidke monitor eemal mistahes magnetilistest esemetest. Need võivad põhjustada värvi muutumist või moonutada kujutist. Ärge paigaldage seadet kõikuvale, ebatasasele pinnale või kohtadesse, kus esineb vibratsiooni. Seadme kukkumine võib põhjustada vigastusi nii seadmele kui ka kasutajale. Seadme kasutamine kohtades, kus esineb vibratsiooni, lühendab toote kasutusiga ja võib põhjustada tulekahju.
Resumen del contenido incluido en la página 9
SyncMaster 591s / 591v / 793s / 793v / 997DF /793DF 793MB / 795DF / 795MB / 797DF Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Unpacking Monitor and Stand (Some models include a stand attached.) Manual Warranty Card User's Guide, Quick Setup Guide (Not available in all Monitor Driver, locations) Natural Color software Cable SyncMaster 997DF
Resumen del contenido incluido en la página 10
Power Cord Signal Cable (Option) Stand Stand For Multimedia model (Option) Manual User Guide Cable Sound Cables(2each) DC Power Cord Stand Multimedia Speaker Stand Front
Resumen del contenido incluido en la página 11
Menu button [ ] Opens the OSD menu. Also used to exit the OSD menu or return to the previous menu. These buttons allow you to highlight and adjust items in the Adjust buttons [ ] menu. Enter button [ ] Used to select the OSD menu. Power button Use this button for turn the monitor on and off. Power indicator This light glows green during normal operation, and blinks green once as the monitor saves your adjustments. See PowerSaver described in the manual for further information reg
Resumen del contenido incluido en la página 12
SyncMaster 591s / 591v / 793s / 793v / 783DF / 793DF / /997DF / 793MB / 795DF / 795MB / 797DF (The configuration at the back of the monitor may vary from product to product.) Power port Connect the power cord for your monitor to the power port on the back of the monitor. Signal Cable Connect the signal cable to the video port on your computer, video board, video card, or graphics card. BNC Connectors (Option) SyncMaster 997DF (The configuration at the back of the monitor ma
Resumen del contenido incluido en la página 13
Bottom Connect the signal cable to the video port on your computer, Signal Cable video board, video card, or graphics card. Power port Connect the power cord for your monitor to the power port on the back of the monitor. Tilt/Swivel Base You can separate the base from the monitor.
Resumen del contenido incluido en la página 14
SyncMaster 783DF Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Unpacking Monitor and Stand (Some models include a stand attached.) Manual Warranty Card User's Guide, Quick Setup Guide (Not available in all Monitor Driver, locations) Natural Color software Cable Power Cord
Resumen del contenido incluido en la página 15
Stand Stand For Multimedia model (Option) Manual User Guide Cable Sound Cables(2each) DC Power Cord Stand Multimedia Speaker Stand Front
Resumen del contenido incluido en la página 16
Menu button [ ] Opens the OSD menu. Also used to exit the OSD menu or return to the previous menu. These buttons allow you to highlight and adjust items in the Adjust buttons [ ] menu. Enter button [ ] Used to select the OSD menu. Power button Use this button for turn the monitor on and off. Power indicator This light glows green during normal operation, and blinks green once as the monitor saves your adjustments. See PowerSaver described in the manual for further information reg
Resumen del contenido incluido en la página 17
Power port Connect the power cord for your monitor to the power port on the back of the monitor. Connect the signal cable to the video port on your computer, Signal Cable video board, video card, or graphics card. See Connecting the Monitor for further information regarding cable connections. Bottom Signal Cable Connect the signal cable to the video port on your computer, video board, video card, or graphics card. Power port Connect the power cord for your monitor
Resumen del contenido incluido en la página 18
SyncMaster 591s / 591v / 793s / 793v / 783DF / 793DF / 793MB / 795DF / 795MB / 797DF / 997DF Setup-For Multimedia model | Multimedia Speaker Stand General | BNC Connectors (Option) General 1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. Connecting to a computer 2-1. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor. Connecting to a new Maci
Resumen del contenido incluido en la página 19
SyncMaster 997DF 1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. Connecting to a computer 2-1. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor. 2-2. Connecting to a new Macintosh Connect the monitor to the Macintosh computer using the D-SUB connection cable. 2-3. Connecting to an old Macintosh Connect your monitor to the Macintosh using the adapter for M
Resumen del contenido incluido en la página 20
Turn off your computer and unplug the power cord. 1. 2. Connect the end of the signal cable to your computer's video port(video board, video card or graphics card). 3. Connect one end of the other sound cable to the Mic Input jack on your sound card or computer.Connect the other end of this cable to the Mic By-pass jack on the back of the monitor stand. 4. Plug the DC power cord from the stand into a nearby outlet. 5. Connect the power cord for your monitor to the power port on the back o
