Resumen del contenido incluido en la página 1
SyncMaster 957DF/900IFT
Resumen del contenido incluido en la página 2
Main > Index Main Page On-Screen Display General Highlight Zone Highlight Zone II MouScreen™ Safety Instructions Troubleshooting Notational Check List Power Q & A Installation Self-Test Feature Check Cleaning Other Introduction Specifications Unpacking General Specifications Front Preset Timing Modes Rear PowerSaver Bottom Setup Information Connecting Your Monitor Service Installing the Monitor Driver Terms Automatic Regulatory Manual Natural Color Base Installation MouScreen™ Authorit
Resumen del contenido incluido en la página 3
Notational Power Installation Clean Other Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock
Resumen del contenido incluido en la página 4
When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode. If the size of your monitor is small, or if the same image is present for long Notational periods of time, you may see afterimages due to damage to the fluorescent substance on the inside of the CDT. Power Installation Clean Do not use a damaged or loose plug. Other This may cause an electric shock or fire. Do not pull the plug out by the wire nor touch the plug
Resumen del contenido incluido en la página 5
Do not cover the vents on the monitor cabinet. Bad ventilation may cause a breakdown or fire. Notational Power Installation Clean Put your monitor in a location with low humidity and a minimum of Other dust. An electric shock or fire could result inside the monitor. Do not drop the monitor when moving it. This may cause damage to the product or human body. Place the monitor on a flat and stable surface. The monitor can cause injury by falling. Set down the monitor carefully. It cou
Resumen del contenido incluido en la página 6
When cleaning the monitor case or the surface of the CDT, wipe with a slightly moistened, soft fabric. Do not clean Flat monitor with water. Use a water-diluted mild detergent. Notational (Some detergents contain significant amounts of alcohol-based solvents, Power which can damage (color change) or crack the monitor case. The Installation antiglare/anti-static surface coating on the CDT may also be affected.) Clean Other Dilute the detergent (1:10 ratio) with water before using. Do not
Resumen del contenido incluido en la página 7
Do not remove cover(or back). No user serviceable parts inside. This may cause an electric shock or a fire. Refer servicing to qualified service personnel. Notational Power Installation Clean Other If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or service. This may cause an electric shock or a fire. Do not place any heavy objects on the monitor. This may cause
Resumen del contenido incluido en la página 8
Keep the monitor away from any magnetic substances. This may cause discoloring or distortion of the image.
Resumen del contenido incluido en la página 9
Monitor and Stand Power Cord Unpacking Stand Front Rear Bottom Signal Cable (Option) (Some models include a stand attached. ) Please make sure the following items are included with your monitor. If any items are Quick Setup Guide missing, contact your dealer. Warranty Card (Not available in all locations) User's Guide and Driver Installation CD USB Cable
Resumen del contenido incluido en la página 10
Unpacking Front Rear Bottom 1. Highlight button The Highlight Zone ensures clear images on TVs, video conferencing systems or photos by emphasizing a certain area on the screen. 2. Exit button Use this button to Exit the active menu or the OSD. 3. Adjust buttons These buttons allow you to highlight and adjust items in the menu. 4. Menu button Use this button to open the OSD and activate a highlighted menu item. 5. Power indicator This light glows green during normal operation, and blinks g
Resumen del contenido incluido en la página 11
Unpacking Front Rear Bottom (The configuration at the back of the monitor may vary from product to product.) 1. Power port Connect the power cord for your monitor to the power port on the back of the monitor. Connect the signal cable to the 15-pin D-sub connector on the back of 2. Signal port your monitor. 3. BNC Connectors Connect the signal cable to the BNC signal port on the back of your monitor. (Option) Connect the USB cable to the USB port on the back of your monitor. 4. USB C
Resumen del contenido incluido en la página 12
Unpacking Front Rear Bottom 1. Signal port Connect the signal cable to the video port on your computer, video board, video card, or graphics card. 2. Power port Connect the power cord for your monitor to the power port on the back of the monitor. 3. Tilt/Swivel Base You can separate the base from the monitor.
Resumen del contenido incluido en la página 13
Main > Setup > Connecting Your Monitor Connecting Your Monitor Installing the Monitor Driver Base Installation 1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2. Connecting the signal cables. 1) Connecting to the PC. (Connect the signal cable to the 15-pin D-sub connector on the back of your monitor. Connect the signal cable to the video port on your computer, video board, vid
Resumen del contenido incluido en la página 14
Main > Setup > Installing the Monitor Driver Automatic Manual Connecting Your Monitor When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating Installing the system to another. Follow the directions as appropriate for the operating system you Monitor Driver have. Base Installation Prepare a blank disk and download the driver program file at the Internet web site shown
Resumen del contenido incluido en la página 15
4. Click the " " button in the " " window. Install Warning 5. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button. * This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor Homepage http://www.samsung-monitor.com/. 6. Monitor driver installation is completed.
Resumen del contenido incluido en la página 16
Main > Setup > Installing the Monitor Driver Automatic Manual Windows XP | Windows 2000 | Windows Me | Windows NT | Linux Connecting Your Monitor Installing the When prompted by the operating system for the monitor driver, insert the CD-ROM Monitor Driver included with this monitor. Driver installation is slightly different from one operating Base Installation system to another. Follow the directions as appropriate for the operating system you have. Prepare a blank disk an
Resumen del contenido incluido en la página 17
5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button. 6. Select "Don't search ,I will.." then click "Next" and then click "Have disk". 7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. 8. If you can see following "Message" window, then click the "Continue Anyway" button. Then click " " button. OK
Resumen del contenido incluido en la página 18
This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor Homepage http://www.samsung-monitor.com/. 9. Click the "Close" button then click "OK" button continually. 10. Monitor driver installation is completed. ® ® Microsoft Windows 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window
Resumen del contenido incluido en la página 19
4. Select the " " tab. Monitor 5. Click the " " button in the " " area. Change Monitor Type 6. Choose "Specify the location of the driver". 7. Choose "Display a list of all the driver in a specific location.." then click "Next" button. 8. Click the "Have Disk" button 9. Specify A:\(D:\driver) then click "OK" button. 10. Select "Show all devices" and choose the monitor that corresponds to the one you connected to your computer and click "OK". 11. Continue choosing "Close" button an
Resumen del contenido incluido en la página 20
Tilt/Swivel Base | Attaching and Removing the Base Connecting Your Monitor With the built-in pedestal, you can tilt and/or swivel the monitor for the most comfortable Installing the Monitor Driver viewing angle. Base Installation The base is detachable. Note: Attaching the Base 1. Place the monitor upside-down on a flat work surface. 2. Align the tabs on the base with the corresponding slots on the bottom of the monitor. 3. Press the base onto the monitor until the tabs are fully enga
