Resumen del contenido incluido en la página 1
Table of Contents
Preface............................................................................................................................... 2
FCC Statement Warning............................................................................................................... 2
Canadian DOC Notice .................................................................................................................. 2
Important Safety Instructions....................................
Resumen del contenido incluido en la página 2
Preface This manual is designed to assist users in setting up and using the LCD Monitor. Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. The information in this document is subject to change without notice. This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic or other means, in any form, w
Resumen del contenido incluido en la página 3
Important Safety Instructions Please read the following instructions carefully. This manual should be retained for future use. 1. To clean LCD Monitor screen; -- Power off LCD Monitor and unplug the AC Cord. -- Spray a non-solvent cleaning solution onto a rag. -- Gently clean the screen with dampened rag. 2. Do not place the LCD Monitor near a window. Exposing the monitor to rain water, moisture or sunlight can severely damage it. 3. Do not apply pressure to the LCD screen. Exce
Resumen del contenido incluido en la página 4
Chapter 1 Installation Unpacking Before unpacking the LCD Monitor, prepare a suitable workspace for your Monitor and computer. You need a stable and clean surface near a wall power outlet. Make sure that LCD Monitor has enough space around it for sufficient airflow. Though the LCD Monitor uses very little power, some ventilation is needed to ensure that the Monitor does not become too hot. AL1715 AL1715 b AL1715 m AL1715 bm AUDIO No No Yes Yes After you unpack the LCD Monitor, mak
Resumen del contenido incluido en la página 5
Detaching LCD Monitor from Its Stand Unscrew screws the swivel base support column and pull down the hinge to release. Figure 1-3 Interface for Arm Applications Before installing to mounting device, please refer to Fig.1-3. The rear of this LCD display has four integrated 4 mm, 0.7 pitches threaded nuts, as well as four 5 mm access holes in the plastic covering as illustrated in Figure 1-4. These specifications meet the VESA Flat Panel Monitor Physical Mounting Interface Standa
Resumen del contenido incluido en la página 6
Connecting the Audio Cable (For AL1715 m and AL1715 bm) 1. Connect the audio cable to the " LINE OUT " jack on your PC's audio card or to the front panel's “AUDIO OUT” jack of your CD ROM drive. (See Fig. 1-7) 2. Connect the other end of the audio cable to the LCD Monitor's " LINE IN " jack. Figure 1-7 Power Management System This LCD Monitor complies with the VESA DPMS (version 1.0) Power Management guidelines. The VESA DPMS provides four power saving modes through detecting a ho
Resumen del contenido incluido en la página 7
Chapter 2 Display Controls General Instructions Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor (See Figure 2-1). By changing these settings, the picture can be adjusted to your personal preferences. The power cord should be connected. Connect the video cable from the monitor to the video card. Press the power button to turn on the monitor position. The power indicator will light up. Figure 2-1 External Co
Resumen del contenido incluido en la página 8
Front Panel Control /Power Button: Press this button to turn the monitor ON or OFF, And display the monitor’s state. Power Indicator: Green — Power On mode. Orange — off mode MENU / ENTER : Activate OSD menu when OSD is OFF or activate/de-activate adjustment function when OSD is ON or Exit OSD menu when in Volume Adjust OSD status.
Resumen del contenido incluido en la página 9
How To Adjust A Setting 1. Press the MENU-button to activate the OSD window. 2. Press < or > to select the desired function. 3. Press the MENU-button to select the function that you want to adjust. 4. Press < or > to change the settings of the current function. 5. To exit and save, select the exit function. If you want to adjust any other function, repeat steps 2-4. Adjusting The Picture The descriptions for function control LEDS Sub Menu Main Menu Icon Sub Menu Item Description Ic
Resumen del contenido incluido en la página 10
N/A English N/A N/A Deutsch N/A Français Multi-language selection. N/A Español N/A Italiano N/A 简 N/A H. Position Adjust the horizontal position of the OSD. Adjust the vertical position of the OSD. V. Position OSD Timeout Adjust the OSD timeout. Auto Adjust the H/V Position, Focus and N/A Auto Config Clock of picture. Show the resolution, H/V frequency and N/A Information input port of current iput timing. Clear each old status of Auto-configuration N/A Res
Resumen del contenido incluido en la página 11
Chapter 3 Technical Information Specifications LCD Panel Size 17" (43 cm) Display Type Active matrix color TFT LCD Resolution 1280 x 1024 Display Dot 1280 x (RGB) x 1024 Display Area (mm)(H x V) 337.92 x 270.336 Display Color 262K 2 2 Brightness 250 cd/m (typical), 200 cd/m (minimum) Contrast Ratio 430:1 (typical) Response Time Ta=25°C Tr+ Tf=20ms Lamp Voltage 700 Vrms (typical) Lamp Current 6.5 mA rms. (typical) Viewing Angle Vertical: -65° ~ +65° Horizontal: -80° ~ +80° 16.7
Resumen del contenido incluido en la página 12
Power Management Mode Power Consumption* AC Input LED Color On 60W maximum 240 VAC Green Off 3W maximum 240 VAC Yellow Soft switch off 3W maximum 240 VAC Dark Yellow: Standby, Suspend, Off Disconnected 3W maximum 240 VAC Dark: DC Power off * Meeting VESA DPMS requirements measured from AC Input end of AC power cord. Sync Input Signal Separate TTL compatible horizontal and vertical synchronization Polarity Positive and negative Supports VESA DDC2B functions Plug & Play External
Resumen del contenido incluido en la página 13
Standard Timing Table If the selected timing is NOT included in table below, this LCD monitor will use the most suitable available timing. TIMING FH(KHZ) SYNC TOTAL ACTIVE SYNC FRONT BACK PIXEL FV(HZ) POLARITY (DOT/ (DOT/ WIDTH PORCH PORCH FOREQ LINE) LINE) (DOT/LINE) (DOT/LINE) (DOT/LINE) (MHZ) 640x350 31.469 + 800 640 96 16 48 25.175 VGA-350 70.087 – 449 350 2 37 60 640x400 24.83 – 848 640 64 64 80 21.05 NEC PC9801 56.42 – 440 400 8 7 25 640x400 31.469 – 800 640 96 16 48 25.175
Resumen del contenido incluido en la página 14
TIMING FH(KHZ) SYNC TOTAL ACTIVE SYNC FRONT BACK PIXEL FV(HZ) POLARITY (DOT/ (DOT/ WIDTH PORCH PORCH FOREQ LINE) LINE) (DOT/LINE) (DOT/LINE) (DOT/LINE) (MHZ) 800x600 46.875 + 1056 800 80 16 160 49.5 VESA-600-75Hz 75 + 625 600 3 1 21 1024x768 48.363 – 1344 1024 136 24 160 65 XGA 60.004 – 806 768 6 3 29 1024x768 53.964 + 1328 1024 176 16 112 71.664 COMPAQ-XGA 66.132 + 816 768 4 8 36 1024x768 56.476 – 1328 1024 136 24 144 75 VESA-768-70Hz 70.069 – 806 768 6 3 29 1024x768 60.023 + 1
Resumen del contenido incluido en la página 15
Troubleshooting This LCD Monitor has pre-adjusted using factory standard VGA timings. Due to the output timing differences among various VGA cards in the market, users may initially experience an unstable or unclear display whenever a new display mode or new VGA card is selected. Attention This LCD Monitor Supports Multiple VGA Modes. Refer to the Standard Timing Table for a listing of modes supported by this LCD Monitor. PROBLEM Picture is unclear and unstable The picture is unclear
