Resumen del contenido incluido en la página 1
Dell™ Inspiron™ i1200 and i2200 Service Manual
Before You Begin
System Components
Memory, Optical Drive, Modem, and Mini PCI Card
Hard Drive
Keyboard
Display
Palm Rest
Coin-Cell Battery
Microprocessor Thermal-Cooling Assembly
Microprocessor Module
Speakers
System Board
Flashing the BIOS
Base Plastics
Pinout Assignments for I/O Connectors
NOTE: A NOTE indicates important information that helps you make better use of your computer.
NOTICE: A NOTICE indicates either potential damag
Resumen del contenido incluido en la página 2
Back to Contents Page Base Plastics Dell™ Inspiron™ i1200 and i2200 Service Manual CAUTION: Before performing the following procedures, read the safety instructions in the Product Information Guide. CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components. You can do so by touching an unpainted metal surface. 1. Follow the instructions in "Before Working Insi
Resumen del contenido incluido en la página 3
Back to Contents Page Before You Begin Dell™ Inspiron™ i1200 and i2200 Service Manual Recommended Tools Turning Off Your Computer Before Working Inside Your Computer Computer Orientation Screw Identification This chapter provides procedures for removing and installing the components in your computer. Unless otherwise noted, each procedure assumes that the following conditions exist: l You have performed the steps in "Turning Off Your Computer" and "Before Working Ins
Resumen del contenido incluido en la página 4
NOTICE: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell is not covered by your warranty. NOTICE: When you disconnect a cable, pull on its connector or on its strain-relief loop, not on the cable itself. Some cables have a connector with locking tabs; if you are disconnecting this type of cable, press in on the locking tabs before you disconnect the cable. As you pull connectors apart, keep them evenly alig
Resumen del contenido incluido en la página 5
1 front 2 left 3 back 4 right Screw Identification When you are removing and replacing components, print this section as a tool to lay out and keep track of the screws. The placemat provides the number of screws and their sizes. Optical Drive: Hard Drive Door: Hard Drive: (1 each) (2 each) (2 each) Modem to EMI Shield: Display Assembly System Board: to Computer Base: (4 each) (2 each) (4 each) Display Bezel:
Resumen del contenido incluido en la página 6
Screw Covers (6 each) Display Bumpers (6 each) Palm Rest to Palm Rest to System Board to Base Plastics: Base Plastics in Hard Drive Base Plastics: Bay: (8 each) (4 each, hard drive cage) (2 each) (2 each, system board) Speakers to Base Plastics: (2 for each speaker, 4 total) Back to Contents Page
Resumen del contenido incluido en la página 7
Back to Contents Page Flashing the BIOS Dell™ Inspiron™ i1200 and i2200 Service Manual Flashing the BIOS From a Floppy Disk or a CD Flashing the BIOS From the Hard Drive If a BIOS-update program floppy disk or CD is provided with the new system board, flash the BIOS from a floppy disk or a CD. If you do not have a BIOS-update program floppy disk or CD, flash the BIOS from the hard drive. Flashing the BIOS From a Floppy Disk or a CD 1. Ensure that the AC adapter is plugged
Resumen del contenido incluido en la página 8
Back to Contents Page
Resumen del contenido incluido en la página 9
Back to Contents Page Coin-Cell Battery Dell™ Inspiron™ i1200 and i2200 Service Manual CAUTION: Before performing the following procedures, read the safety instructions in the Product Information Guide. CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components. You can do so by touching an unpainted metal surface. 1. Follow the instructions in "Before Working
Resumen del contenido incluido en la página 10
Back to Contents Page Microprocessor Module Dell™ Inspiron™ i1200 and i2200 Service Manual Removing the Microprocessor Module Installing the Microprocessor Module Removing the Microprocessor Module CAUTION: Before performing the following procedures, read the safety instructions in the Product Information Guide. CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's elec
Resumen del contenido incluido en la página 11
Installing the Microprocessor Module NOTICE: Ensure that the cam lock is in the fully open position before seating the microprocessor module. Seating the microprocessor module properly in the ZIF socket does not require force. NOTICE: A microprocessor module that is not properly seated can result in an intermittent connection or permanent damage to the microprocessor and ZIF socket. 1. Align the pin-1 corner of the microprocessor module so that it points to the triangle on the system
Resumen del contenido incluido en la página 12
Back to Contents Page Display Dell™ Latitude™ 110L Service Manual Display Assembly Display Bezel Display Panel Display Assembly CAUTION: Before performing the following procedures, read the safety instructions in the Product Information Guide. CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components. You can do so by touching an unpainted metal sur
Resumen del contenido incluido en la página 13
1 M2.5 x 5-mm screws (4) 2 shield retention tabs (3) 3 shield-retention tab slots 6. Disconnect the attached antenna cable from the Mini PCI card. 1 antenna cable 2 metal securing tabs (2) 3 Mini PCI card connector 4 Mini PCI card 7. Close the display. 8. From the bottom of the computer, remove the two M2.5 x 5-mm screws labeled "D."
Resumen del contenido incluido en la página 14
9. From the back of the computer, remove the two M2.5 x 8-mm screws labeled "D." 10. Pull straight up on the pull-tab that is attached to the display-feed flex cable to disconnect the cable from the system board. 1 display cable 2 system board connector 11. Carefully remove the Mini PCI card antenna cable and the display cables from their routing guides. 12. Lift the display assembly out of the computer base.
Resumen del contenido incluido en la página 15
1 screw covers/display bumpers (6) 2 display bezel 3 M2.5 x 5-mm screws (6) 4 display panel 5 M2 x 3-mm screws (8) 6 top cover 7 display-feed flex cable Display Bezel CAUTION: Before performing the following procedures, read the safety instructions in the Product Information Guide. CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components. You
Resumen del contenido incluido en la página 16
CAUTION: Before performing the following procedures, read the safety instructions in the Product Information Guide. CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components. You can do so by touching an unpainted metal surface. 1. Follow the instructions in "Before Working Inside Your Computer." 2. Remove the display assembly. 3. Remove the display bezel.
Resumen del contenido incluido en la página 17
Back to Contents Page Hard Drive Dell™ Inspiron™ i1200 and i2200 Service Manual Removing the Hard Drive Installing the Hard Drive Removing the Hard Drive CAUTION: If you remove the hard drive from the computer when the drive is hot, do not touch the metal housing of the hard drive. CAUTION: Before working inside your computer, follow the safety instructions located in the Product Information Guide. NOTICE: To prevent data loss, turn off your computer before removing
Resumen del contenido incluido en la página 18
NOTE: You need the Drivers and Utilities CD to install the drivers and utilities on the new hard drive. The Drivers and Utilities CD is optional and may not ship with your computer. See your Owner's Manual for more information. 5. Remove the new drive from its packaging. Save the original packaging for storing or shipping the hard drive. NOTICE: Use firm and even pressure to slide the drive into place. If you use excessive force, you may damage the connector. 6. Slide the hard dri
Resumen del contenido incluido en la página 19
Back to Contents Page Keyboard Dell™ Inspiron™ i1200 and i2200 Service Manual Removing the Keyboard Installing the Keyboard Removing the Keyboard CAUTION: Before working inside your Dell™ computer, read the safety instructions in your Product Information Guide. CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components. You can do so by touching an unpa
Resumen del contenido incluido en la página 20
NOTICE: The keycaps on the keyboard are fragile, easily dislodged, and time-consuming to replace. Be careful when removing and handling the keyboard. 6. Lift the top of the keyboard out of the computer base, and pull the keyboard out at an angle toward the display to access the connector. 7. Grasp the interface connector lever near the edge of the keyboard connector, and rotate the lever toward you to raise the interface connector lever. 8. Lift the keyboard flex cable to remove
